MLK-11230 imx6: USB: Modify OTG ID pin pad setting to pull up

Set the ID pin pad to pull up not the pull down at default, otherwise
we can't enter the device mode, but always detect as host.

After this change we have to use portA cable to play as host,
and use portB cable for device.

Signed-off-by: Ye.Li <B37916@freescale.com>

6 files changed, 31 insertions, 6 deletions

diff --git a/board/freescale/mx6qarm2/mx6qarm2.c b/board/freescale/mx6qarm2/mx6qarm2.c
index f74257f..9d0bc18 100644
--- a/board/freescale/mx6qarm2/mx6qarm2.c
+++ b/board/freescale/mx6qarm2/mx6qarm2.c
@@ -32,6 +32,10 @@ DECLARE_GLOBAL_DATA_PTR;
 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
 	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
 
+#define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
 int dram_init(void)
 {
 #if defined(CONFIG_MX6DL) && !defined(CONFIG_MX6DL_LPDDR2) && \
@@ -236,7 +240,7 @@ int board_eth_init(bd_t *bis)
 
 static iomux_v3_cfg_t const usb_otg_pads[] = {
 	MX6_PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
 };
 
 static void setup_usb(void)
diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
index 60eb273..8035c40 100644
--- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
+++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
@@ -79,6 +79,10 @@ DECLARE_GLOBAL_DATA_PTR;
 	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
 	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
 
+#define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
 #define I2C_PMIC	1
 
 int dram_init(void)
@@ -889,7 +893,7 @@ int checkboard(void)
 #define USB_OTG_PWR       PORTEXP_IO_NR(0x34, 1)
 
 iomux_v3_cfg_t const usb_otg_pads[] = {
-	MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
 };
 
 int board_ehci_hcd_init(int port)
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 2ada005..8a12965 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -67,6 +67,11 @@ DECLARE_GLOBAL_DATA_PTR;
 #define EPDC_PAD_CTRL    (PAD_CTL_PKE | PAD_CTL_SPEED_MED |	\
 	PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
 
+#define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+
 #define I2C_PMIC	1
 
 #define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
@@ -779,7 +784,7 @@ int board_eth_init(bd_t *bis)
 
 static iomux_v3_cfg_t const usb_otg_pads[] = {
 	MX6_PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
 };
 
 static iomux_v3_cfg_t const usb_hc1_pads[] = {
diff --git a/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
index 0b29119..eb15517 100644
--- a/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
+++ b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
@@ -76,6 +76,10 @@ DECLARE_GLOBAL_DATA_PTR;
 #define LCD_PAD_CTRL    (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
 	PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm)
 
+#define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
 /*Define for building port exp gpio, pin starts from 0*/
 #define PORTEXP_IO_NR(chip, pin) \
 	((chip << 5) + pin)
@@ -371,7 +375,7 @@ void ldo_mode_set(int ldo_bypass)
 static iomux_v3_cfg_t const usb_otg_pads[] = {
 	/* OGT1 */
 	MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
 	/* OTG2 */
 	MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
 };
diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
index 46256b4..a2e0f71 100644
--- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
+++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
@@ -83,6 +83,10 @@ DECLARE_GLOBAL_DATA_PTR;
 #define WDOG_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_PKE | PAD_CTL_SPEED_MED |	\
 	PAD_CTL_DSE_40ohm)
 
+#define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
 int dram_init(void)
 {
 	gd->ram_size = PHYS_SDRAM_SIZE;
@@ -386,7 +390,7 @@ void ldo_mode_set(int ldo_bypass)
 static iomux_v3_cfg_t const usb_otg_pads[] = {
 	/* OGT1 */
 	MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
 	/* OTG2 */
 	MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
 };
diff --git a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
index 508fbd7..c6ac36e 100644
--- a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
+++ b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
@@ -85,6 +85,10 @@ DECLARE_GLOBAL_DATA_PTR;
 	PAD_CTL_SPEED_MED |		\
 	PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
 
+#define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
 #define IOX_SDI IMX_GPIO_NR(5, 10)
 #define IOX_STCP IMX_GPIO_NR(5, 7)
 #define IOX_SHCP IMX_GPIO_NR(5, 11)
@@ -547,7 +551,7 @@ int board_mmc_init(bd_t *bis)
 #define UCTRL_PWR_POL		(1 << 9)
 
 static iomux_v3_cfg_t const usb_otg_pads[] = {
-	MX6_PAD_GPIO1_IO00__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO00__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
 };
 
 /* At default the 3v3 enables the MIC2026 for VBUS power */