ppc4xx: Update 440SP/440SPe DDR SPD setup code to support 440SP

Signed-off-by: Stefan Roese <sr@denx.de>

2 files changed, 63 insertions, 26 deletions

diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c
index 35b2315..c4da739 100644
--- a/cpu/ppc4xx/44x_spd_ddr2.c
+++ b/cpu/ppc4xx/44x_spd_ddr2.c
@@ -188,6 +188,7 @@ static void program_initplr(unsigned long *dimm_populated,
                             ddr_cas_id_t selected_cas,
 			    int write_recovery);
 static unsigned long is_ecc_enabled(void);
+#ifdef CONFIG_DDR_ECC
 static void program_ecc(unsigned long *dimm_populated,
 			unsigned char *iic0_dimm_addr,
 			unsigned long num_dimm_banks,
@@ -195,6 +196,7 @@ static void program_ecc(unsigned long *dimm_populated,
 static void program_ecc_addr(unsigned long start_address,
 			     unsigned long num_bytes,
 			     unsigned long tlb_word2_i_value);
+#endif
 static void program_DQS_calibration(unsigned long *dimm_populated,
 				    unsigned char *iic0_dimm_addr,
 				    unsigned long num_dimm_banks);
@@ -255,15 +257,6 @@ static void mtdcr_any(u32 dcr, u32 val)
 	}
 }
 
-static void wait_ddr_idle(void)
-{
-	u32 val;
-
-	do {
-		mfsdram(SDRAM_MCSTAT, val);
-	} while ((val & SDRAM_MCSTAT_IDLE_MASK) == SDRAM_MCSTAT_IDLE_NOT);
-}
-
 static unsigned char spd_read(uchar chip, uint addr)
 {
 	unsigned char data[2];
@@ -491,7 +484,7 @@ long int initdram(int board_type)
 		(val & ~(SDRAM_MEMODE_DIC_MASK  | SDRAM_MEMODE_DLL_MASK |
 			 SDRAM_MEMODE_RTT_MASK | SDRAM_MEMODE_DQS_MASK)) |
 		(SDRAM_MEMODE_DIC_NORMAL | SDRAM_MEMODE_DLL_ENABLE
-		 | SDRAM_MEMODE_RTT_75OHM | SDRAM_MEMODE_DQS_ENABLE));
+		 | SDRAM_MEMODE_RTT_150OHM | SDRAM_MEMODE_DQS_ENABLE));
 
 	/*------------------------------------------------------------------
 	 * Program Initialization preload registers.
@@ -537,10 +530,12 @@ long int initdram(int board_type)
 	 *-----------------------------------------------------------------*/
 	program_DQS_calibration(dimm_populated, iic0_dimm_addr, num_dimm_banks);
 
+#ifdef CONFIG_DDR_ECC
 	/*------------------------------------------------------------------
 	 * If ecc is enabled, initialize the parity bits.
 	 *-----------------------------------------------------------------*/
 	program_ecc(dimm_populated, iic0_dimm_addr, num_dimm_banks, MY_TLB_WORD2_I_ENABLE);
+#endif
 
 #ifdef DEBUG
 	ppc440sp_sdram_register_dump();
@@ -702,7 +697,7 @@ static void check_frequency(unsigned long *dimm_populated,
 	 *-----------------------------------------------------------------*/
 	get_sys_info(&board_cfg);
 
-	mfsdr(sdr_ddr0, sdr_ddrpll);
+	mfsdr(SDR0_DDR0, sdr_ddrpll);
 	sdram_freq = ((board_cfg.freqPLB) * SDR0_DDR0_DDRM_DECODE(sdr_ddrpll));
 
 	/*
@@ -877,7 +872,11 @@ static void program_copt1(unsigned long *dimm_populated,
 	unsigned long ddrtype;
 	unsigned long val;
 
+#ifdef CONFIG_DDR_ECC
 	ecc_enabled = TRUE;
+#else
+	ecc_enabled = FALSE;
+#endif
 	dimm_32bit = FALSE;
 	dimm_64bit = FALSE;
 	buf0 = FALSE;
@@ -1314,7 +1313,7 @@ static void program_mode(unsigned long *dimm_populated,
 	 *-----------------------------------------------------------------*/
 	get_sys_info(&board_cfg);
 
-	mfsdr(sdr_ddr0, sdr_ddrpll);
+	mfsdr(SDR0_DDR0, sdr_ddrpll);
 	sdram_freq = MULDIV64((board_cfg.freqPLB), SDR0_DDR0_DDRM_DECODE(sdr_ddrpll), 1);
 
 	/*------------------------------------------------------------------
@@ -1463,11 +1462,12 @@ static void program_mode(unsigned long *dimm_populated,
 	mfsdram(SDRAM_MMODE, mmode);
 	mmode = mmode & ~(SDRAM_MMODE_WR_MASK | SDRAM_MMODE_DCL_MASK);
 
-	cycle_2_0_clk = MULDIV64(ONE_BILLION, 100, max_2_0_tcyc_ns_x_100);
-	cycle_2_5_clk = MULDIV64(ONE_BILLION, 100, max_2_5_tcyc_ns_x_100);
-	cycle_3_0_clk = MULDIV64(ONE_BILLION, 100, max_3_0_tcyc_ns_x_100);
-	cycle_4_0_clk = MULDIV64(ONE_BILLION, 100, max_4_0_tcyc_ns_x_100);
-	cycle_5_0_clk = MULDIV64(ONE_BILLION, 100, max_5_0_tcyc_ns_x_100);
+	/* add 10 here because of rounding problems */
+	cycle_2_0_clk = MULDIV64(ONE_BILLION, 100, max_2_0_tcyc_ns_x_100) + 10;
+	cycle_2_5_clk = MULDIV64(ONE_BILLION, 100, max_2_5_tcyc_ns_x_100) + 10;
+	cycle_3_0_clk = MULDIV64(ONE_BILLION, 100, max_3_0_tcyc_ns_x_100) + 10;
+	cycle_4_0_clk = MULDIV64(ONE_BILLION, 100, max_4_0_tcyc_ns_x_100) + 10;
+	cycle_5_0_clk = MULDIV64(ONE_BILLION, 100, max_5_0_tcyc_ns_x_100) + 10;
 
 	if (sdram_ddr1 == TRUE) { /* DDR1 */
 		if ((cas_2_0_available == TRUE) && (sdram_freq <= cycle_2_0_clk)) {
@@ -1498,7 +1498,11 @@ static void program_mode(unsigned long *dimm_populated,
 		} else {
 			printf("ERROR: Cannot find a supported CAS latency with the installed DIMMs.\n");
 			printf("Only DIMMs DDR2 with CAS latencies of 3.0, 4.0, and 5.0 are supported.\n");
-			printf("Make sure the PLB speed is within the supported range of the DIMMs.\n\n");
+			printf("Make sure the PLB speed is within the supported range of the DIMMs.\n");
+			printf("cas3=%d cas4=%d cas5=%d\n",
+			       cas_3_0_available, cas_4_0_available, cas_5_0_available);
+			printf("sdram_freq=%d cycle3=%d cycle4=%d cycle5=%d\n\n",
+			       sdram_freq, cycle_3_0_clk, cycle_4_0_clk, cycle_5_0_clk);
 			hang();
 		}
 	}
@@ -1575,7 +1579,7 @@ static void program_rtr(unsigned long *dimm_populated,
 	/*------------------------------------------------------------------
 	 * Set the SDRAM Refresh Timing Register, SDRAM_RTR
 	 *-----------------------------------------------------------------*/
-	mfsdr(sdr_ddr0, sdr_ddrpll);
+	mfsdr(SDR0_DDR0, sdr_ddrpll);
 	sdram_freq = ((board_cfg.freqPLB) * SDR0_DDR0_DDRM_DECODE(sdr_ddrpll));
 
 	max_refresh_rate = 0;
@@ -1661,7 +1665,7 @@ static void program_tr(unsigned long *dimm_populated,
 	 *-----------------------------------------------------------------*/
 	get_sys_info(&board_cfg);
 
-	mfsdr(sdr_ddr0, sdr_ddrpll);
+	mfsdr(SDR0_DDR0, sdr_ddrpll);
 	sdram_freq = ((board_cfg.freqPLB) * SDR0_DDR0_DDRM_DECODE(sdr_ddrpll));
 
 	/*------------------------------------------------------------------
@@ -2069,7 +2073,7 @@ static void program_memory_queue(unsigned long *dimm_populated,
 			 * Set the sizes
 			 *-----------------------------------------------------------------*/
 			baseadd_size = 0;
-			rank_size_bytes = 1024 * 1024 * rank_size_id;
+			rank_size_bytes = 4 * 1024 * 1024 * rank_size_id;
 			switch (rank_size_id) {
 			case 0x02:
 				baseadd_size |= SDRAM_RXBAS_SDSZ_8;
@@ -2106,8 +2110,8 @@ static void program_memory_queue(unsigned long *dimm_populated,
 
 			for (i = 0; i < num_ranks; i++)	{
 				mtdcr_any(rank_reg+i+dimm_num+bank_0_populated,
-					  (rank_base_addr & SDRAM_RXBAS_SDBA_MASK) |
-					  baseadd_size);
+					  (SDRAM_RXBAS_SDBA_ENCODE(rank_base_addr) |
+					   baseadd_size));
 				rank_base_addr += rank_size_bytes;
 			}
 		}
@@ -2130,9 +2134,10 @@ static unsigned long is_ecc_enabled(void)
 		ecc = max(ecc, SDRAM_MCOPT1_MCHK_CHK_DECODE(val));
 	}
 
-	return(ecc);
+	return ecc;
 }
 
+#ifdef CONFIG_DDR_ECC
 /*-----------------------------------------------------------------------------+
  * program_ecc.
  *-----------------------------------------------------------------------------*/
@@ -2208,6 +2213,15 @@ static void check_ecc(void)
 }
 #endif
 
+static void wait_ddr_idle(void)
+{
+	u32 val;
+
+	do {
+		mfsdram(SDRAM_MCSTAT, val);
+	} while ((val & SDRAM_MCSTAT_IDLE_MASK) == SDRAM_MCSTAT_IDLE_NOT);
+}
+
 /*-----------------------------------------------------------------------------+
  * program_ecc_addr.
  *-----------------------------------------------------------------------------*/
@@ -2276,6 +2290,7 @@ static void program_ecc_addr(unsigned long start_address,
 #endif
 	}
 }
+#endif
 
 /*-----------------------------------------------------------------------------+
  * program_DQS_calibration.
@@ -2531,7 +2546,6 @@ static void DQS_calibration_process(void)
 		}
 	}		/* for rffd */
 
-
 	/*------------------------------------------------------------------
 	 * Set the average RFFD value
 	 *-----------------------------------------------------------------*/
diff --git a/include/ppc440.h b/include/ppc440.h
index 1c7f11c..5fe4076 100644
--- a/include/ppc440.h
+++ b/include/ppc440.h
@@ -417,7 +417,9 @@
 #define SDR0_PEGPLLSET1		0x000003A0	/* PE Pll LC Tank Setting1 */
 #define SDR0_PEGPLLSET2		0x000003A1	/* PE Pll LC Tank Setting2 */
 #define SDR0_PEGPLLSTS		0x000003A2	/* PE Pll LC Tank Status */
+#endif /* CONFIG_440SPE */
 
+#if defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 /*----------------------------------------------------------------------------+
 | SDRAM Controller
 +----------------------------------------------------------------------------*/
@@ -453,9 +455,16 @@
 /*-----------------------------------------------------------------------------+
 |  Memory Bank 0-7 configuration
 +-----------------------------------------------------------------------------*/
-#define SDRAM_RXBAS_SDBA_MASK		0xFF800000	/* Base address	*/
+#if defined(CONFIG_440SPE)
+#define SDRAM_RXBAS_SDBA_MASK		0xFFE00000	/* Base address	*/
 #define SDRAM_RXBAS_SDBA_ENCODE(n)	((((unsigned long)(n))&0xFFE00000)>>2)
 #define SDRAM_RXBAS_SDBA_DECODE(n)	((((unsigned long)(n))&0xFFE00000)<<2)
+#endif /* CONFIG_440SPE */
+#if defined(CONFIG_440SP)
+#define SDRAM_RXBAS_SDBA_MASK		0xFF800000	/* Base address	*/
+#define SDRAM_RXBAS_SDBA_ENCODE(n)	((((unsigned long)(n))&0xFF800000))
+#define SDRAM_RXBAS_SDBA_DECODE(n)	((((unsigned long)(n))&0xFF800000))
+#endif /* CONFIG_440SP */
 #define SDRAM_RXBAS_SDSZ_MASK		0x0000FFC0	/* Size		*/
 #define SDRAM_RXBAS_SDSZ_ENCODE(n)	((((unsigned long)(n))&0x3FF)<<6)
 #define SDRAM_RXBAS_SDSZ_DECODE(n)	((((unsigned long)(n))>>6)&0x3FF)
@@ -2167,6 +2176,20 @@
 /*-----------------------------------------------------------------------------+
 |  SDR0 Bit Settings
 +-----------------------------------------------------------------------------*/
+#if defined(CONFIG_440SP)
+#define SDR0_SRST			0x0200
+
+#define SDR0_DDR0			0x00E1
+#define SDR0_DDR0_DPLLRST		0x80000000
+#define SDR0_DDR0_DDRM_MASK		0x60000000
+#define SDR0_DDR0_DDRM_DDR1		0x20000000
+#define SDR0_DDR0_DDRM_DDR2		0x40000000
+#define SDR0_DDR0_DDRM_ENCODE(n)	((((unsigned long)(n))&0x03)<<29)
+#define SDR0_DDR0_DDRM_DECODE(n)	((((unsigned long)(n))>>29)&0x03)
+#define SDR0_DDR0_TUNE_ENCODE(n)	((((unsigned long)(n))&0x2FF)<<0)
+#define SDR0_DDR0_TUNE_DECODE(n)	((((unsigned long)(n))>>0)&0x2FF)
+#endif
+
 #if defined(CONFIG_440SPE)
 #define SDR0_CP440			0x0180
 #define SDR0_CP440_ERPN_MASK		0x30000000