powerpc: ppc4xx: remove korat board support

This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Larry Johnson <lrj@acm.org>

13 files changed, 1 insertions, 1514 deletions

diff --git a/arch/powerpc/cpu/ppc4xx/Kconfig b/arch/powerpc/cpu/ppc4xx/Kconfig
index 75e4507..9e52d3f 100644
--- a/arch/powerpc/cpu/ppc4xx/Kconfig
+++ b/arch/powerpc/cpu/ppc4xx/Kconfig
@@ -13,9 +13,6 @@ config TARGET_CSB272
 config TARGET_CSB472
 	bool "Support csb472"
 
-config TARGET_KORAT
-	bool "Support korat"
-
 config TARGET_LWMON5
 	bool "Support lwmon5"
 	select SUPPORT_SPL
@@ -195,7 +192,6 @@ source "board/gdsys/405ex/Kconfig"
 source "board/gdsys/dlvision/Kconfig"
 source "board/gdsys/gdppc440etx/Kconfig"
 source "board/gdsys/intip/Kconfig"
-source "board/korat/Kconfig"
 source "board/lwmon5/Kconfig"
 source "board/mosaixtech/icon/Kconfig"
 source "board/mpl/mip405/Kconfig"
diff --git a/board/korat/Kconfig b/board/korat/Kconfig
deleted file mode 100644
index f434dea..0000000
--- a/board/korat/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_KORAT
-
-config SYS_BOARD
-	default "korat"
-
-config SYS_CONFIG_NAME
-	default "korat"
-
-endif
diff --git a/board/korat/MAINTAINERS b/board/korat/MAINTAINERS
deleted file mode 100644
index 8b96846..0000000
--- a/board/korat/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-KORAT BOARD
-M:	Larry Johnson <lrj@acm.org>
-S:	Maintained
-F:	board/korat/
-F:	include/configs/korat.h
-F:	configs/korat_defconfig
-F:	configs/korat_perm_defconfig
diff --git a/board/korat/Makefile b/board/korat/Makefile
deleted file mode 100644
index 63914bc..0000000
--- a/board/korat/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2002-2007
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= korat.o
-extra-y	+= init.o
diff --git a/board/korat/README b/board/korat/README
deleted file mode 100644
index e059f78..0000000
--- a/board/korat/README
+++ /dev/null
@@ -1,64 +0,0 @@
-The Korat board has two NOR flashes, FLASH0 and FLASH1, which are connected to
-chip select 0 and 1, respectively.  FLASH0 contains 16 MiB, and is mapped to
-addresses 0xFF000000 - 0xFFFFFFFF as U-Boot Flash Bank #2.  FLASH1 contains
-from 16 to 128 MiB, and is mapped to 0xF?000000 - 0xF7FFFFFF as U-Boot Flash
-Bank #1 (with the starting address depending on the flash size detected at
-runtime).  The write-enable pin on FLASH0 is disabled, so the contents of FLASH0
-cannot be modified in the field.  This also prevents FLASH0 from executing
-commands to return chip information, so its configuration is hard-coded in
-U-Boot.
-
-There are two versions of U-Boot for Korat: "permanent" and "upgradable".  The
-permanent U-Boot is pre-programmed at the top of FLASH0, e.g., at addresses
-0xFFFA0000 - 0xFFFFFFFF for the current 384 KiB size.  The upgradable U-Boot is
-located 256 KiB from the top of FLASH1, e.g. at addresses 0xF7F6000 - 0xF7FC0000
-for the current 384 KiB size.  FLASH1 addresses 0xF7FE0000 - 0xF7FF0000 are
-used for the U-Boot environmental parameters, and addresses 0xF7FC0000 -
-0xF7FDFFFF are used for the redundant copy of the parameters.  These locations
-are used by both versions of U-Boot.
-
-On booting, the permanent U-Boot in FLASH0 begins executing.  After performing
-minimal setup, it monitors the state of the board's Reset switch (GPIO47).  If
-the switch is sensed as open before a timeout period, then U-Boot branches to
-address 0xF7FBFFFC.  This causes the upgradable U-Boot to execute from the
-beginning.  If the switch remains closed thoughout the timeout period, the
-permanent U-Boot activates the on-board buzzer until the switch is sensed as
-opened.  It then continues to execute without branching to FLASH1.  The effect
-of this is that normally the Korat board boots its upgradable U-Boot, but, if
-this has been corrupted, the user can boot the permanent U-Boot, which can then
-be used to erase and reload FLASH1 as needed.
-
-Note that it is not necessary for the permanent U-Boot to have all the latest
-features, but only that it have sufficient functionality (working "tftp",
-"erase", "cp.b", etc.) to repair FLASH1.  Also, the permanent U-Boot makes no
-assumptions about the size of FLASH1 or the size of the upgradable U-Boot: it is
-sufficient that the upgradable U-Boot can be started by a branch to 0xF7FBFFFC.
-
-The build sequence:
-
-	make korat_perm_config
-	make all
-
-builds the permanent U-Boot by selecting loader file "u-boot.lds" and defining
-preprocessor symbol "CONFIG_KORAT_PERMANENT".  The default build:
-
-	make korat_config
-	make all
-
-creates the upgradable U-Boot by selecting loader file "u-boot-F7FC.lds" and
-leaving preprocessor symbol "CONFIG_KORAT_PERMANENT" undefined.
-
-2008-02-22, Larry Johnson <lrj@acm.org>
-
-
-The CompactFlash(R) controller on the Korat board provides a hi-speed USB
-interface.  This may be connected to either a dedicated port on the on-board
-USB controller, or to a USB port on the PowerPC 440EPx processor.  The U-Boot
-environment variable "korat_usbcf" can be used to specify which of these two
-USB host ports is used for CompactFlash.  The valid setting for the variable are
-the strings "pci" and "ppc".  If the variable defined and set to "ppc", then the
-PowerPC USB port is used.  In all other cases the on-board USB controller is
-used, but if "korat_usbcf" is defined but is set to a string other than the two
-valid options, a warning is also issued.
-
-2009-01-28, Larry Johnson <lrj@acm.org>
diff --git a/board/korat/config.mk b/board/korat/config.mk
deleted file mode 100644
index 42e0060..0000000
--- a/board/korat/config.mk
+++ /dev/null
@@ -1,27 +0,0 @@
-#
-# (C) Copyright 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-#
-# Korat (PPC440EPx) board
-#
-
-PLATFORM_CPPFLAGS += -DCONFIG_440=1
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif
-
-ifeq ($(emul),1)
-PLATFORM_CPPFLAGS += -fno-schedule-insns -fno-schedule-insns2
-endif
-
-ifeq ($(dbcr),1)
-PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8CFF0000
-endif
-
-ifndef CONFIG_KORAT_PERMANENT
-LDSCRIPT := $(srctree)/board/$(BOARDDIR)/u-boot-F7FC.lds
-endif
diff --git a/board/korat/init.S b/board/korat/init.S
deleted file mode 100644
index 20c5bdd..0000000
--- a/board/korat/init.S
+++ /dev/null
@@ -1,80 +0,0 @@
-/*
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <asm-offsets.h>
-#include <ppc_asm.tmpl>
-#include <asm/mmu.h>
-#include <config.h>
-
-/**************************************************************************
- * TLB TABLE
- *
- * This table is used by the cpu boot code to setup the initial tlb
- * entries. Rather than make broad assumptions in the cpu source tree,
- * this table lets each board set things up however they like.
- *
- *  Pointer to the table is returned in r1
- *
- *************************************************************************/
-    .section .bootpg,"ax"
-    .globl tlbtab
-
-tlbtab:
-	tlbtab_start
-
-	/*
-	 * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
-	 * speed up boot process. It is patched after relocation to enable SA_I
-	 */
-	tlbentry( 0xF0000000, SZ_256M, 0xF0000000, 1, AC_RWX | SA_G )
-
-	/*
-	 * TLB entries for SDRAM are not needed on this platform.  They are
-	 * generated dynamically in the SPD DDR2 detection routine.
-	 */
-
-#ifdef CONFIG_SYS_INIT_RAM_DCACHE
-	/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
-	tlbentry( CONFIG_SYS_INIT_RAM_ADDR, SZ_64K, CONFIG_SYS_INIT_RAM_ADDR, 0,
-		  AC_RWX | SA_G )
-#endif
-
-	/* TLB-entry for PCI Memory */
-	tlbentry( CONFIG_SYS_PCI_MEMBASE + 0x00000000, SZ_256M,
-		  CONFIG_SYS_PCI_MEMBASE + 0x00000000, 1, AC_RW | SA_IG )
-
-	tlbentry( CONFIG_SYS_PCI_MEMBASE + 0x10000000, SZ_256M,
-		  CONFIG_SYS_PCI_MEMBASE + 0x10000000, 1, AC_RW | SA_IG )
-
-	tlbentry( CONFIG_SYS_PCI_MEMBASE + 0x20000000, SZ_256M,
-		  CONFIG_SYS_PCI_MEMBASE + 0x20000000, 1, AC_RW | SA_IG )
-
-	tlbentry( CONFIG_SYS_PCI_MEMBASE + 0x30000000, SZ_256M,
-		  CONFIG_SYS_PCI_MEMBASE + 0x30000000, 1, AC_RW | SA_IG )
-
-	/* TLB-entry for EBC */
-	tlbentry( CONFIG_SYS_CPLD_BASE, SZ_1K, CONFIG_SYS_CPLD_BASE, 1, AC_RW | SA_IG )
-
-	/* TLB-entry for Internal Registers & OCM */
-	/* I wonder why this must be executable -- lrj@acm.org 2007-10-08 */
-	tlbentry( 0xE0000000, SZ_16M, 0xE0000000, 0, AC_RWX | SA_I )
-
-	/*TLB-entry PCI registers*/
-	tlbentry( 0xEEC00000, SZ_1K, 0xEEC00000, 1, AC_RW | SA_IG )
-
-	/* TLB-entry for peripherals */
-	tlbentry( 0xEF000000, SZ_16M, 0xEF000000, 1, AC_RW | SA_IG)
-
-	/* TLB-entry PCI IO Space - from sr@denx.de */
-	tlbentry(0xE8000000, SZ_64K, 0xE8000000, 1, AC_RW | SA_IG)
-
-	tlbtab_end
-
-#if defined(CONFIG_KORAT_PERMANENT)
-	.globl	korat_branch_absolute
-korat_branch_absolute:
-	mtlr	r3
-	blr
-#endif
diff --git a/board/korat/korat.c b/board/korat/korat.c
deleted file mode 100644
index d9ab2fd..0000000
--- a/board/korat/korat.c
+++ /dev/null
@@ -1,633 +0,0 @@
-/*
- * (C) Copyright 2007-2010
- * Larry Johnson, lrj@acm.org
- *
- * (C) Copyright 2006-2007
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2006
- * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
- * Alain Saurel,	    AMCC/IBM, alain.saurel@fr.ibm.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <fdt_support.h>
-#include <i2c.h>
-#include <libfdt.h>
-#include <asm/ppc440.h>
-#include <asm/bitops.h>
-#include <asm/ppc4xx-gpio.h>
-#include <asm/io.h>
-#include <asm/ppc4xx-uic.h>
-#include <asm/processor.h>
-#include <asm/4xx_pci.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-ulong flash_get_size(ulong base, int banknum);
-
-#if defined(CONFIG_KORAT_PERMANENT)
-void korat_buzzer(int const on)
-{
-	if (on) {
-		out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x05,
-		      in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x05) | 0x80);
-	} else {
-		out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x05,
-		      in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x05) & ~0x80);
-	}
-}
-#endif
-
-int board_early_init_f(void)
-{
-	uint32_t sdr0_pfc1, sdr0_pfc2;
-	uint32_t reg;
-	int eth;
-
-#if defined(CONFIG_KORAT_PERMANENT)
-	unsigned mscount;
-
-	extern void korat_branch_absolute(uint32_t addr);
-
-	for (mscount = 0;  mscount < CONFIG_SYS_KORAT_MAN_RESET_MS; ++mscount) {
-		udelay(1000);
-		if (gpio_read_in_bit(CONFIG_SYS_GPIO_RESET_PRESSED_)) {
-			/* This call does not return. */
-			korat_branch_absolute(
-				CONFIG_SYS_FLASH1_TOP - 2 * CONFIG_ENV_SECT_SIZE - 4);
-		}
-	}
-	korat_buzzer(1);
-	while (!gpio_read_in_bit(CONFIG_SYS_GPIO_RESET_PRESSED_))
-		udelay(1000);
-
-	korat_buzzer(0);
-#endif
-
-	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	mtdcr(EBC0_CFGDATA, 0xb8400000);
-
-	/*
-	 * Setup the interrupt controller polarities, triggers, etc.
-	 */
-	mtdcr(UIC0SR, 0xffffffff);	/* clear all */
-	mtdcr(UIC0ER, 0x00000000);	/* disable all */
-	mtdcr(UIC0CR, 0x00000005);	/* ATI & UIC1 crit are critical */
-	mtdcr(UIC0PR, 0xfffff7ff);	/* per ref-board manual */
-	mtdcr(UIC0TR, 0x00000000);	/* per ref-board manual */
-	mtdcr(UIC0VR, 0x00000000);	/* int31 highest, base=0x000 */
-	mtdcr(UIC0SR, 0xffffffff);	/* clear all */
-
-	mtdcr(UIC1SR, 0xffffffff);	/* clear all */
-	mtdcr(UIC1ER, 0x00000000);	/* disable all */
-	mtdcr(UIC1CR, 0x00000000);	/* all non-critical */
-	mtdcr(UIC1PR, 0xffffffff);	/* per ref-board manual */
-	mtdcr(UIC1TR, 0x00000000);	/* per ref-board manual */
-	mtdcr(UIC1VR, 0x00000000);	/* int31 highest, base=0x000 */
-	mtdcr(UIC1SR, 0xffffffff);	/* clear all */
-
-	mtdcr(UIC2SR, 0xffffffff);	/* clear all */
-	mtdcr(UIC2ER, 0x00000000);	/* disable all */
-	mtdcr(UIC2CR, 0x00000000);	/* all non-critical */
-	mtdcr(UIC2PR, 0xffffffff);	/* per ref-board manual */
-	mtdcr(UIC2TR, 0x00000000);	/* per ref-board manual */
-	mtdcr(UIC2VR, 0x00000000);	/* int31 highest, base=0x000 */
-	mtdcr(UIC2SR, 0xffffffff);	/* clear all */
-
-	/*
-	 * Take sim card reader and CF controller out of reset.  Also enable PHY
-	 * auto-detect until board-specific PHY resets are available.
-	 */
-	out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x02, 0xC0);
-
-	/* Configure the two Ethernet PHYs.  For each PHY, configure for fiber
-	 * if the SFP module is present, and for copper if it is not present.
-	 */
-	for (eth = 0; eth < 2; ++eth) {
-		if (gpio_read_in_bit(CONFIG_SYS_GPIO_SFP0_PRESENT_ + eth)) {
-			/* SFP module not present: configure PHY for copper. */
-			/* Set PHY to autonegotate 10 MB, 100MB, or 1 GB */
-			out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x03,
-			      in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x03) |
-			      0x06 << (4 * eth));
-		} else {
-			/* SFP module present: configure PHY for fiber and
-			   enable output */
-			gpio_write_bit(CONFIG_SYS_GPIO_PHY0_FIBER_SEL + eth, 1);
-			gpio_write_bit(CONFIG_SYS_GPIO_SFP0_TX_EN_ + eth, 0);
-		}
-	}
-	/* enable Ethernet: set GPIO45 and GPIO46 to 1 */
-	gpio_write_bit(CONFIG_SYS_GPIO_PHY0_EN, 1);
-	gpio_write_bit(CONFIG_SYS_GPIO_PHY1_EN, 1);
-
-	/* Wait 1 ms, then enable Fiber signal detect to PHYs. */
-	udelay(1000);
-	out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x03,
-	      in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x03) | 0x88);
-
-	/* select Ethernet (and optionally IIC1) pins */
-	mfsdr(SDR0_PFC1, sdr0_pfc1);
-	sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) |
-		SDR0_PFC1_SELECT_CONFIG_4;
-#ifdef CONFIG_I2C_MULTI_BUS
-	sdr0_pfc1 |= ((sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_IIC1_SEL);
-#endif
-	mfsdr(SDR0_PFC2, sdr0_pfc2);
-	sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) |
-		SDR0_PFC2_SELECT_CONFIG_4;
-	mtsdr(SDR0_PFC2, sdr0_pfc2);
-	mtsdr(SDR0_PFC1, sdr0_pfc1);
-
-	/* PCI arbiter enabled */
-	mfsdr(SDR0_PCI0, reg);
-	mtsdr(SDR0_PCI0, 0x80000000 | reg);
-
-	return 0;
-}
-
-/*
- * The boot flash on CS0 normally has its write-enable pin disabled, and so will
- * not respond to CFI commands.  This routine therefore fills in the flash
- * information for the boot flash.  (The flash at CS1 operates normally.)
- */
-ulong board_flash_get_legacy (ulong base, int banknum, flash_info_t * info)
-{
-	uint32_t addr;
-	int i;
-
-	if (1 != banknum)
-		return 0;
-
-	info->size		= CONFIG_SYS_FLASH0_SIZE;
-	info->sector_count	= CONFIG_SYS_FLASH0_SIZE / 0x20000;
-	info->flash_id		= 0x01000000;
-	info->portwidth		= 2;
-	info->chipwidth		= 2;
-	info->buffer_size	= 32;
-	info->erase_blk_tout	= 16384;
-	info->write_tout	= 2;
-	info->buffer_write_tout	= 5;
-	info->vendor		= 2;
-	info->cmd_reset		= 0x00F0;
-	info->interface		= 2;
-	info->legacy_unlock	= 0;
-	info->manufacturer_id	= 1;
-	info->device_id		= 0x007E;
-
-#if CONFIG_SYS_FLASH0_SIZE == 0x01000000
-	info->device_id2	= 0x2101;
-#elif CONFIG_SYS_FLASH0_SIZE == 0x04000000
-	info->device_id2	= 0x2301;
-#else
-#error Unable to set device_id2 for current CONFIG_SYS_FLASH0_SIZE
-#endif
-
-	info->ext_addr		= 0x0040;
-	info->cfi_version	= 0x3133;
-	info->cfi_offset	= 0x0055;
-	info->addr_unlock1	= 0x00000555;
-	info->addr_unlock2	= 0x000002AA;
-	info->name		= "CFI conformant";
-	for (i = 0, addr = -info->size;
-	     i < info->sector_count;
-	     ++i, addr += 0x20000) {
-		info->start[i] = addr;
-		info->protect[i] = 0x00;
-	}
-	return 1;
-}
-
-static int man_data_read(unsigned int addr)
-{
-	/*
-	 * Read an octet of data from address "addr" in the manufacturer's
-	 * information serial EEPROM, or -1 on error.
-	 */
-	u8 data[2];
-
-	if (0 != i2c_probe(MAN_DATA_EEPROM_ADDR) ||
-	    0 != i2c_read(MAN_DATA_EEPROM_ADDR, addr, 1, data, 1)) {
-		debug("man_data_read(0x%02X) failed\n", addr);
-		return -1;
-	}
-	debug("man_info_read(0x%02X) returned 0x%02X\n", addr, data[0]);
-	return data[0];
-}
-
-static unsigned int man_data_field_addr(unsigned int const field)
-{
-	/*
-	 * The manufacturer's information serial EEPROM contains a sequence of
-	 * zero-delimited fields.  Return the starting address of field "field",
-	 * or 0 on error.
-	 */
-	unsigned addr, i;
-
-	if (0 == field || 'A' != man_data_read(0) || '\0' != man_data_read(1))
-		/* Only format "A" is currently supported */
-		return 0;
-
-	for (addr = 2, i = 1; i < field && addr < 256; ++addr) {
-		if ('\0' == man_data_read(addr))
-			++i;
-	}
-	return (addr < 256) ? addr : 0;
-}
-
-static char *man_data_read_field(char s[], unsigned const field,
-				 unsigned const length)
-{
-	/*
-	 * Place the null-terminated contents of field "field" of length
-	 * "length" from the manufacturer's information serial EEPROM into
-	 * string "s[length + 1]" and return a pointer to s, or return 0 on
-	 * error. In either case the original contents of s[] is not preserved.
-	 */
-	unsigned addr, i;
-
-	addr = man_data_field_addr(field);
-	if (0 == addr || addr + length >= 255)
-		return 0;
-
-	for (i = 0; i < length; ++i) {
-		int const c = man_data_read(addr++);
-
-		if (c <= 0)
-			return 0;
-
-		s[i] = (char)c;
-	}
-	if (0 != man_data_read(addr))
-		return 0;
-
-	s[i] = '\0';
-	return s;
-}
-
-static void set_serial_number(void)
-{
-	/*
-	 * If the environmental variable "serial#" is not set, try to set it
-	 * from the manufacturer's information serial EEPROM.
-	 */
-	char s[MAN_INFO_LENGTH + MAN_MAC_ADDR_LENGTH + 2];
-
-	if (getenv("serial#"))
-		return;
-
-	if (!man_data_read_field(s, MAN_INFO_FIELD, MAN_INFO_LENGTH))
-		return;
-
-	s[MAN_INFO_LENGTH] = '-';
-	if (!man_data_read_field(s + MAN_INFO_LENGTH + 1, MAN_MAC_ADDR_FIELD,
-				 MAN_MAC_ADDR_LENGTH))
-		return;
-
-	setenv("serial#", s);
-}
-
-static void set_mac_addresses(void)
-{
-	/*
-	 * If the environmental variables "ethaddr" and/or "eth1addr" are not
-	 * set, try to set them from the manufacturer's information serial
-	 * EEPROM.
-	 */
-
-#if MAN_MAC_ADDR_LENGTH % 2 != 0
-#error MAN_MAC_ADDR_LENGTH must be an even number
-#endif
-
-	char s[(3 * MAN_MAC_ADDR_LENGTH) / 2];
-	char *src;
-	char *dst;
-
-	if (0 != getenv("ethaddr") && 0 != getenv("eth1addr"))
-		return;
-
-	if (0 == man_data_read_field(s + (MAN_MAC_ADDR_LENGTH / 2) - 1,
-				     MAN_MAC_ADDR_FIELD, MAN_MAC_ADDR_LENGTH))
-		return;
-
-	for (src = s + (MAN_MAC_ADDR_LENGTH / 2) - 1, dst = s; src != dst;) {
-		*dst++ = *src++;
-		*dst++ = *src++;
-		*dst++ = ':';
-	}
-	if (0 == getenv("ethaddr"))
-		setenv("ethaddr", s);
-
-	if (0 == getenv("eth1addr")) {
-		++s[((3 * MAN_MAC_ADDR_LENGTH) / 2) - 2];
-		setenv("eth1addr", s);
-	}
-}
-
-int misc_init_r(void)
-{
-	uint32_t pbcr;
-	int size_val;
-	uint32_t reg;
-	unsigned long usb2d0cr = 0;
-	unsigned long usb2phy0cr, usb2h0cr = 0;
-	unsigned long sdr0_pfc1;
-	uint32_t const flash1_size = gd->bd->bi_flashsize - CONFIG_SYS_FLASH0_SIZE;
-	char const *const act = getenv("usbact");
-	char const *const usbcf = getenv("korat_usbcf");
-
-	/*
-	 * Re-do FLASH1 sizing and adjust flash start and offset.
-	 */
-	gd->bd->bi_flashstart = CONFIG_SYS_FLASH1_TOP - flash1_size;
-	gd->bd->bi_flashoffset = 0;
-
-	mtdcr(EBC0_CFGADDR, PB1CR);
-	pbcr = mfdcr(EBC0_CFGDATA);
-	size_val = ffs(flash1_size) - 21;
-	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
-	mtdcr(EBC0_CFGADDR, PB1CR);
-	mtdcr(EBC0_CFGDATA, pbcr);
-
-	/*
-	 * Re-check to get correct base address
-	 */
-	flash_get_size(gd->bd->bi_flashstart, 0);
-
-	/*
-	 * Re-do FLASH1 sizing and adjust flash offset to reserve space for
-	 * environment
-	 */
-	gd->bd->bi_flashoffset =
-		CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - CONFIG_SYS_FLASH1_ADDR;
-
-	mtdcr(EBC0_CFGADDR, PB1CR);
-	pbcr = mfdcr(EBC0_CFGDATA);
-	size_val = ffs(gd->bd->bi_flashsize - CONFIG_SYS_FLASH0_SIZE) - 21;
-	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
-	mtdcr(EBC0_CFGADDR, PB1CR);
-	mtdcr(EBC0_CFGDATA, pbcr);
-
-	/* Monitor protection ON by default */
-#if defined(CONFIG_KORAT_PERMANENT)
-	(void)flash_protect(FLAG_PROTECT_SET, CONFIG_SYS_MONITOR_BASE,
-			    CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN - 1,
-			    flash_info + 1);
-#else
-	(void)flash_protect(FLAG_PROTECT_SET, CONFIG_SYS_MONITOR_BASE,
-			    CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN - 1,
-			    flash_info);
-#endif
-	/* Env protection ON by default */
-	(void)flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR,
-			    CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
-			    flash_info);
-	(void)flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR_REDUND,
-			    CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1,
-			    flash_info);
-
-	/*
-	 * USB suff...
-	 */
-	/*
-	 * Select the USB controller on the 440EPx ("ppc") or on the PCI bus
-	 * ("pci") for the CompactFlash.
-	 */
-	if (usbcf != NULL && (strcmp(usbcf, "ppc") == 0)) {
-		/*
-		 * If environment variable "usbcf" is defined and set to "ppc",
-		 * then connect the CompactFlash controller to the PowerPC USB
-		 * port.
-		 */
-		printf("Attaching CompactFlash controller to PPC USB\n");
-		out_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x02,
-		      in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0x02) | 0x10);
-	} else {
-		if (usbcf != NULL && (strcmp(usbcf, "pci") != 0))
-			printf("Warning: \"korat_usbcf\" is not set to a legal "
-			       "value (\"ppc\" or \"pci\")\n");
-
-		printf("Attaching CompactFlash controller to PCI USB\n");
-	}
-	if (act == NULL || strcmp(act, "hostdev") == 0) {
-		/* SDR Setting */
-		mfsdr(SDR0_PFC1, sdr0_pfc1);
-		mfsdr(SDR0_USB2D0CR, usb2d0cr);
-		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
-		mfsdr(SDR0_USB2H0CR, usb2h0cr);
-
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ;
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;
-
-		/*
-		 * An 8-bit/60MHz interface is the only possible alternative
-		 * when connecting the Device to the PHY
-		 */
-		usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
-		usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ;
-
-		/*
-		 * To enable the USB 2.0 Device function
-		 * through the UTMI interface
-		 */
-		usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
-		usb2d0cr = usb2d0cr | SDR0_USB2D0CR_USB2DEV_SELECTION;
-
-		sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK;
-		sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL;
-
-		mtsdr(SDR0_PFC1, sdr0_pfc1);
-		mtsdr(SDR0_USB2D0CR, usb2d0cr);
-		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
-		mtsdr(SDR0_USB2H0CR, usb2h0cr);
-
-		/* clear resets */
-		udelay(1000);
-		mtsdr(SDR0_SRST1, 0x00000000);
-		udelay(1000);
-		mtsdr(SDR0_SRST0, 0x00000000);
-
-		printf("USB:   Host(int phy) Device(ext phy)\n");
-
-	} else if (strcmp(act, "dev") == 0) {
-		/*-------------------PATCH-------------------------------*/
-		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
-
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;
-		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
-
-		udelay(1000);
-		mtsdr(SDR0_SRST1, 0x672c6000);
-
-		udelay(1000);
-		mtsdr(SDR0_SRST0, 0x00000080);
-
-		udelay(1000);
-		mtsdr(SDR0_SRST1, 0x60206000);
-
-		*(unsigned int *)(0xe0000350) = 0x00000001;
-
-		udelay(1000);
-		mtsdr(SDR0_SRST1, 0x60306000);
-		/*-------------------PATCH-------------------------------*/
-
-		/* SDR Setting */
-		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
-		mfsdr(SDR0_USB2H0CR, usb2h0cr);
-		mfsdr(SDR0_USB2D0CR, usb2d0cr);
-		mfsdr(SDR0_PFC1, sdr0_pfc1);
-
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ;
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PUREN;
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_DEV;
-		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
-		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_DEV;
-
-		usb2h0cr   = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
-		usb2h0cr   = usb2h0cr | SDR0_USB2H0CR_WDINT_8BIT_60MHZ;
-
-		usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
-		usb2d0cr = usb2d0cr | SDR0_USB2D0CR_EBC_SELECTION;
-
-		sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK;
-		sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_EBCHR_SEL;
-
-		mtsdr(SDR0_USB2H0CR, usb2h0cr);
-		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
-		mtsdr(SDR0_USB2D0CR, usb2d0cr);
-		mtsdr(SDR0_PFC1, sdr0_pfc1);
-
-		/* clear resets */
-		udelay(1000);
-		mtsdr(SDR0_SRST1, 0x00000000);
-		udelay(1000);
-		mtsdr(SDR0_SRST0, 0x00000000);
-
-		printf("USB:   Device(int phy)\n");
-	}
-
-	mfsdr(SDR0_SRST1, reg);		/* enable security/kasumi engines */
-	reg &= ~(SDR0_SRST1_CRYP0 | SDR0_SRST1_KASU0);
-	mtsdr(SDR0_SRST1, reg);
-
-	/*
-	 * Clear PLB4A0_ACR[WRP]
-	 * This fix will make the MAL burst disabling patch for the Linux
-	 * EMAC driver obsolete.
-	 */
-	reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK;
-	mtdcr(PLB4A0_ACR, reg);
-
-	set_serial_number();
-	set_mac_addresses();
-	gpio_write_bit(CONFIG_SYS_GPIO_ATMEGA_RESET_, 1);
-
-	return 0;
-}
-
-int checkboard(void)
-{
-	char const *const s = getenv("serial#");
-	u8 const rev = in_8((u8 *) CONFIG_SYS_CPLD_BASE + 0);
-
-	printf("Board: Korat, Rev. %X", rev);
-	if (s)
-		printf(", serial# %s", s);
-
-	printf(".\n       Ethernet PHY 0: ");
-	if (gpio_read_out_bit(CONFIG_SYS_GPIO_PHY0_FIBER_SEL))
-		printf("fiber");
-	else
-		printf("copper");
-
-	printf(", PHY 1: ");
-	if (gpio_read_out_bit(CONFIG_SYS_GPIO_PHY1_FIBER_SEL))
-		printf("fiber");
-	else
-		printf("copper");
-
-	printf(".\n");
-#if defined(CONFIG_KORAT_PERMANENT)
-	printf("       Executing permanent copy of U-Boot.\n");
-#endif
-	return 0;
-}
-
-#if defined(CONFIG_PCI) && defined(CONFIG_PCI_PNP)
-/*
- * Assign interrupts to PCI devices.
- */
-void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
-{
-	pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2);
-}
-#endif
-
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/* First do 440EP(x) common setup */
-	__pci_target_init(hose);
-
-	/*
-	 * Set up Configuration registers for on-board NEC uPD720101 USB
-	 * controller.
-	 */
-	pci_write_config_dword(PCI_BDF(0x0, 0xC, 0x0), 0xE4, 0x00000020);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, bd_t *bd)
-{
-	u32 val[4];
-	int rc;
-
-	ft_cpu_setup(blob, bd);
-
-	/* Fixup NOR mapping */
-	val[0] = 1;				/* chip select number */
-	val[1] = 0;				/* always 0 */
-	val[2] = gd->bd->bi_flashstart;
-	val[3] = gd->bd->bi_flashsize - CONFIG_SYS_FLASH0_SIZE;
-	rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges",
-				  val, sizeof(val), 1);
-	if (rc)
-		printf("Unable to update property NOR mapping, err=%s\n",
-		       fdt_strerror(rc));
-
-	return 0;
-}
-#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
diff --git a/board/korat/u-boot-F7FC.lds b/board/korat/u-boot-F7FC.lds
deleted file mode 100644
index bee4d9a..0000000
--- a/board/korat/u-boot-F7FC.lds
+++ /dev/null
@@ -1,124 +0,0 @@
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
-   __DYNAMIC = 0;    */
-SECTIONS
-{
-  .resetvec 0xF7FBFFFC :
-  {
-    *(.resetvec)
-  } = 0xffff
-
-  .bootpg 0xF7FBF000 :
-  {
-    arch/powerpc/cpu/ppc4xx/start.o	(.bootpg)
-  } = 0xffff
-
-  /* Read-only sections, merged into text segment: */
-  . = + SIZEOF_HEADERS;
-  .interp : { *(.interp) }
-  .hash          : { *(.hash)		}
-  .dynsym        : { *(.dynsym)		}
-  .dynstr        : { *(.dynstr)		}
-  .rel.text      : { *(.rel.text)		}
-  .rela.text     : { *(.rela.text)	}
-  .rel.data      : { *(.rel.data)		}
-  .rela.data     : { *(.rela.data)	}
-  .rel.rodata    : { *(.rel.rodata)	}
-  .rela.rodata   : { *(.rela.rodata)	}
-  .rel.got       : { *(.rel.got)		}
-  .rela.got      : { *(.rela.got)		}
-  .rel.ctors     : { *(.rel.ctors)	}
-  .rela.ctors    : { *(.rela.ctors)	}
-  .rel.dtors     : { *(.rel.dtors)	}
-  .rela.dtors    : { *(.rela.dtors)	}
-  .rel.bss       : { *(.rel.bss)		}
-  .rela.bss      : { *(.rela.bss)		}
-  .rel.plt       : { *(.rel.plt)		}
-  .rela.plt      : { *(.rela.plt)		}
-  .init          : { *(.init)	}
-  .plt : { *(.plt) }
-  .text      :
-  {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
-
-    arch/powerpc/cpu/ppc4xx/start.o	(.text)
-
-    *(.text)
-    *(.got1)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-  }
-  .fini      : { *(.fini)    } =0
-  .ctors     : { *(.ctors)   }
-  .dtors     : { *(.dtors)   }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
-  _erotext = .;
-  PROVIDE (erotext = .);
-  .reloc   :
-  {
-    *(.got)
-    _GOT2_TABLE_ = .;
-    *(.got2)
-    _FIXUP_TABLE_ = .;
-    *(.fixup)
-  }
-  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data)
-    *(.data1)
-    *(.sdata)
-    *(.sdata2)
-    *(.dynamic)
-    CONSTRUCTORS
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-  . = .;
-
-  .u_boot_list : {
-	KEEP(*(SORT(.u_boot_list*)));
-  }
-
-  . = .;
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(256);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(256);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss (NOLOAD)       :
-  {
-   *(.sbss) *(.scommon)
-   *(.dynbss)
-   *(.bss)
-   *(COMMON)
-   . = ALIGN(4);
-  }
-
-  __bss_end = . ;
-  PROVIDE (end = .);
-}
diff --git a/configs/korat_defconfig b/configs/korat_defconfig
deleted file mode 100644
index d363aab..0000000
--- a/configs/korat_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_KORAT=y
diff --git a/configs/korat_perm_defconfig b/configs/korat_perm_defconfig
deleted file mode 100644
index 8c6b4c4..0000000
--- a/configs/korat_perm_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="KORAT_PERMANENT"
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_KORAT=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 1f2320b..59d2142 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
 
 Board            Arch        CPU            Commit      Removed     Last known maintainer/contact
 =================================================================================================
+korat            powerpc     ppc4xx         -           -           Larry Johnson <lrj@acm.org>
 galaxy5200       powerpc     mpc5xxx        -           -           Eric Millbrandt <emillbrandt@dekaresearch.com>
 W7OLMC           powerpc     ppc4xx         -           -           Erik Theisen <etheisen@mindspring.com>
 W7OLMG           powerpc     ppc4xx         -           -           Erik Theisen <etheisen@mindspring.com>
diff --git a/include/configs/korat.h b/include/configs/korat.h
deleted file mode 100644
index 5494a60..0000000
--- a/include/configs/korat.h
+++ /dev/null
@@ -1,550 +0,0 @@
-/*
- * (C) Copyright 2007-2009
- * Larry Johnson, lrj@acm.org
- *
- * (C) Copyright 2006-2007
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2006
- * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
- * Alain Saurel,            AMCC/IBM, alain.saurel@fr.ibm.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * korat.h - configuration for Korat board
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_440EPX		1	/* Specific PPC440EPx		*/
-#define CONFIG_SYS_CLK_FREQ	33333333
-
-#ifdef CONFIG_KORAT_PERMANENT
-#define CONFIG_SYS_TEXT_BASE	0xFFFA0000
-#else
-#define	CONFIG_SYS_TEXT_BASE	0xF7F60000
-#endif
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
-#define CONFIG_MISC_INIT_R	1	/* Call misc_init_r		*/
-
-/*
- * Manufacturer's information serial EEPROM parameters
- */
-#define MAN_DATA_EEPROM_ADDR	0x53	/* EEPROM I2C address		*/
-#define MAN_INFO_FIELD		2
-#define MAN_INFO_LENGTH		9
-#define MAN_MAC_ADDR_FIELD	3
-#define MAN_MAC_ADDR_LENGTH	12
-
-/*
- * Base addresses -- Note these are effective addresses where the actual
- * resources get mapped (not physical addresses).
- */
-#define CONFIG_SYS_MONITOR_LEN		(384 * 1024) /* Reserve 384 kiB for Monitor  */
-#define CONFIG_SYS_MALLOC_LEN		(256 * 1024) /* Reserve 256 kiB for malloc() */
-
-#define CONFIG_SYS_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
-#define CONFIG_SYS_FLASH0_SIZE		0x01000000
-#define CONFIG_SYS_FLASH0_ADDR		(-CONFIG_SYS_FLASH0_SIZE)
-#define CONFIG_SYS_FLASH1_TOP		0xF8000000
-#define CONFIG_SYS_FLASH1_MAX_SIZE	0x08000000
-#define CONFIG_SYS_FLASH1_ADDR		(CONFIG_SYS_FLASH1_TOP - CONFIG_SYS_FLASH1_MAX_SIZE)
-#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_FLASH1_ADDR	/* start of FLASH	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_OCM_BASE		0xe0010000	/* ocm			*/
-#define CONFIG_SYS_OCM_DATA_ADDR	CONFIG_SYS_OCM_BASE
-#define CONFIG_SYS_PCI_BASE		0xe0000000	/* Internal PCI regs	*/
-#define CONFIG_SYS_PCI_MEMBASE		0x80000000	/* mapped pci memory	*/
-#define CONFIG_SYS_PCI_MEMBASE2		(CONFIG_SYS_PCI_MEMBASE + 0x20000000)
-
-#define CONFIG_SYS_USB2D0_BASE		0xe0000100
-#define CONFIG_SYS_USB_DEVICE		0xe0000000
-#define CONFIG_SYS_USB_HOST		0xe0000400
-#define CONFIG_SYS_CPLD_BASE		0xc0000000
-
-/*
- * Initial RAM & stack pointer
- */
-/* 440EPx has 16KB of internal SRAM, so no need for D-Cache		*/
-#undef CONFIG_SYS_INIT_RAM_DCACHE
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_BASE	/* OCM			*/
-#define CONFIG_SYS_INIT_RAM_SIZE	(4 << 10)
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
-#define CONFIG_SYS_EXT_SERIAL_CLOCK	11059200	/* ext. 11.059MHz clk	*/
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_SYS_BAUDRATE_TABLE						\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-/*
- * Environment
- */
-#define CONFIG_ENV_IS_IN_FLASH	1	/* use FLASH for environ vars	*/
-
-/*
- * FLASH related
- */
-#define CONFIG_SYS_FLASH_CFI			/* The flash is CFI compatible	      */
-#define CONFIG_FLASH_CFI_DRIVER		/* Use common CFI driver	      */
-#define CONFIG_FLASH_CFI_LEGACY		/* Allow hard-coded config for FLASH0 */
-
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH1_ADDR, CONFIG_SYS_FLASH0_ADDR }
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks	      */
-#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* max number of sectors on one chip  */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)    */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)    */
-
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)   */
-#define CONFIG_SYS_FLASH_PROTECTION	1	/* use hardware flash protection      */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO	      /* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash      */
-
-#define CONFIG_ENV_SECT_SIZE	0x20000	/* size of one complete sector	      */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH1_TOP - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE		0x2000	/* Total Size of Environment Sector   */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
-
-/*
- * DDR SDRAM
- */
-#define CONFIG_DDR_DATA_EYE		/* use DDR2 optimization	*/
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for setup	*/
-#define CONFIG_ZERO_SDRAM		/* Zero SDRAM after setup	*/
-#define CONFIG_DDR_ECC			/* Use ECC when available	*/
-#define SPD_EEPROM_ADDRESS	{0x50}
-#define CONFIG_PROG_SDRAM_TLB
-#define CONFIG_SYS_MEM_TOP_HIDE	(4 << 10) /* don't use last 4 KiB as	*/
-					/* per 440EPx Errata CHIP_11	*/
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
-
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
-#define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/* I2C RTC */
-#define CONFIG_RTC_M41T60	1
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68
-
-/* I2C SYSMON (LM73)							*/
-#define CONFIG_DTT_LM73		1	/* National Semi's LM73		*/
-#define CONFIG_DTT_SENSORS	{2}	/* Sensor addresses		*/
-#define CONFIG_SYS_DTT_MAX_TEMP	70
-#define CONFIG_SYS_DTT_MIN_TEMP	-30
-
-#define CONFIG_PREBOOT	"echo;"						\
-	"echo Type \\\"run flash_cf\\\" to mount from CompactFlash(R);" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#define CONFIG_HOSTNAME		korat
-
-/* Note: kernel_addr and ramdisk_addr assume that FLASH1 is 64 MiB. */
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"u_boot=korat/u-boot.bin\0"					\
-	"load=tftp 200000 ${u_boot}\0"					\
-	"update=protect off F7F60000 F7FBFFFF;erase F7F60000 F7FBFFFF;"	\
-		"cp.b ${fileaddr} F7F60000 ${filesize};protect on "	\
-		"F7F60000 F7FBFFFF\0"					\
-	"upd=run load update\0"						\
-	"bootfile=korat/uImage\0"					\
-	"dtb=korat/korat.dtb\0"						\
-	"kernel_addr=F4000000\0"					\
-	"ramdisk_addr=F4400000\0"					\
-	"dtb_addr=F41E0000\0"						\
-	"udl=tftp 200000 ${bootfile}; erase F4000000 F41DFFFF; "	\
-		"cp.b ${fileaddr} F4000000 ${filesize}\0"		\
-	"udd=tftp 200000 ${dtb}; erase F41E0000 F41FFFFF; "		\
-		"cp.b ${fileaddr} F41E0000 ${filesize}\0"		\
-	"ll=setenv kernel_addr 200000; setenv dtb_addr 1000000; "	\
-		"tftp ${kernel_addr} ${uImage}; tftp ${dtb_addr} "	\
-		"${dtb}\0"						\
-	"rd_size=73728\0"						\
-	"ramargs=setenv bootargs root=/dev/ram rw "			\
-		"ramdisk_size=${rd_size}\0"				\
-	"usbdev=sda1\0"							\
-	"usbargs=setenv bootargs root=/dev/${usbdev} ro rootdelay=10\0"	\
-	"rootpath=/opt/eldk/ppc_4xxFP\0"				\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"pciclk=33\0"							\
-	"addide=setenv bootargs ${bootargs} ide=reverse "		\
-		"idebus=${pciclk}\0"					\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_cf=run usbargs addide addip addtty; "			\
-		"bootm ${kernel_addr} - ${dtb_addr}\0"			\
-	"flash_nfs=run nfsargs addide addip addtty; "			\
-		"bootm ${kernel_addr} - ${dtb_addr}\0"			\
-	"flash_self=run ramargs addip addtty; "				\
-		"bootm ${kernel_addr} ${ramdisk_addr} ${dtb_addr}\0"	\
-	""
-
-#define CONFIG_BOOTCOMMAND	"run flash_cf"
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_IBM_EMAC4_V4	1
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR		2	/* PHY address, See schematics	*/
-#define CONFIG_PHY_DYNAMIC_ANEG	1
-
-#undef CONFIG_PHY_RESET			/* Don't do software PHY reset	*/
-#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_SYS_RX_ETH_BUFFER	32	/* Number of ethernet rx	*/
-					/*   buffers & descriptors	*/
-#define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
-#define CONFIG_PHY1_ADDR	3
-
-/* USB */
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-
-/* Comment this out to enable USB 1.1 device */
-#define USB_2_0_DEVICE
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_USB
-
-/* POST support */
-#define CONFIG_POST		(CONFIG_SYS_POST_CACHE	| \
-				 CONFIG_SYS_POST_CPU	| \
-				 CONFIG_SYS_POST_ECC	| \
-				 CONFIG_SYS_POST_ETHER	| \
-				 CONFIG_SYS_POST_FPU	| \
-				 CONFIG_SYS_POST_I2C	| \
-				 CONFIG_SYS_POST_MEMORY	| \
-				 CONFIG_SYS_POST_RTC	| \
-				 CONFIG_SYS_POST_SPR	| \
-				 CONFIG_SYS_POST_UART)
-
-#define CONFIG_LOGBUFFER
-#define CONFIG_SYS_POST_CACHE_ADDR	0xC8000000	/* free virtual address     */
-
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* Otherwise it catches logbuffer as output */
-
-#define CONFIG_SUPPORT_VFAT
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-					/* Print Buffer Size		*/
-#define CONFIG_SYS_MAXARGS	        16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	        CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000 /* memtest works on		*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000  /* default load address	*/
-#define CONFIG_SYS_EXTBDINFO		1  /* To use extended board_into (bd_t)	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW		1	/* enable loopw command		*/
-#define CONFIG_MX_CYCLIC	1	/* enable mdc/mwc commands	*/
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable	*/
-
-/*
- * Korat-specific options
- */
-#define CONFIG_SYS_KORAT_MAN_RESET_MS	10000	/* timeout for manufacturer reset */
-
-/*
- * PCI stuff
- */
-/* General PCI */
-#define CONFIG_PCI			/* include pci support		*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
-#define CONFIG_SYS_PCI_CACHE_LINE_SIZE	0	/* to avoid problems with PNP	*/
-#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/
-#define CONFIG_SYS_PCI_TARGBASE	0x80000000	/* PCIaddr mapped to	*/
-						/*   CONFIG_SYS_PCI_MEMBASE	*/
-/* Board-specific PCI */
-#define CONFIG_SYS_PCI_TARGET_INIT
-#define CONFIG_SYS_PCI_MASTER_INIT
-#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC				*/
-#define CONFIG_SYS_PCI_SUBSYS_ID       0xcafe	/* Whatever			*/
-
-/*
- * For booting Linux, the board info and command line data have to be in the
- * first 8 MB of memory, since this is the maximum mapped by the Linux kernel
- * during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
-
-/*
- * External Bus Controller (EBC) Setup
- */
-
-/* Memory Bank 0 (NOR-FLASH) initialization				*/
-#if CONFIG_SYS_FLASH0_SIZE == 0x01000000
-#define CONFIG_SYS_EBC_PB0AP		0x04017300
-#define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_FLASH0_ADDR | 0x0009A000)
-#elif CONFIG_SYS_FLASH0_SIZE == 0x04000000
-#define CONFIG_SYS_EBC_PB0AP		0x04017300
-#define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_FLASH0_ADDR | 0x000DA000)
-#else
-#error Unable to configure chip select for current CONFIG_SYS_FLASH0_SIZE
-#endif
-
-/* Memory Bank 1 (NOR-FLASH) initialization				*/
-#if CONFIG_SYS_FLASH1_MAX_SIZE == 0x08000000
-#define CONFIG_SYS_EBC_PB1AP		0x04017300
-#define CONFIG_SYS_EBC_PB1CR		(CONFIG_SYS_FLASH1_ADDR | 0x000FA000)
-#else
-#error Unable to configure chip select for current CONFIG_SYS_FLASH1_MAX_SIZE
-#endif
-
-/* Memory Bank 2 (CPLD) initialization					*/
-#define CONFIG_SYS_EBC_PB2AP		0x04017300
-#define CONFIG_SYS_EBC_PB2CR		(CONFIG_SYS_CPLD_BASE | 0x00038000)
-
-/*
- * GPIO Setup
- *
- * Korat GPIO usage:
- *
- *                   Init.
- * Pin    Source I/O value Function
- * ------ ------ --- ----- ---------------------------------
- * GPIO00  Alt1  I/O   x   PerAddr07
- * GPIO01  Alt1  I/O   x   PerAddr06
- * GPIO02  Alt1  I/O   x   PerAddr05
- * GPIO03  GPIO   x    x   GPIO03 to expansion bus connector
- * GPIO04  GPIO   x    x   GPIO04 to expansion bus connector
- * GPIO05  GPIO   x    x   GPIO05 to expansion bus connector
- * GPIO06  Alt1   O    x   PerCS1 (2nd NOR flash)
- * GPIO07  Alt1   O    x   PerCS2 (CPLD)
- * GPIO08  Alt1   O    x   PerCS3 to expansion bus connector
- * GPIO09  Alt1   O    x   PerCS4 to expansion bus connector
- * GPIO10  Alt1   O    x   PerCS5 to expansion bus connector
- * GPIO11  Alt1   I    x   PerErr
- * GPIO12  GPIO   O    0   ATMega !Reset
- * GPIO13  GPIO   x    x   Test Point 2 (TP2)
- * GPIO14  GPIO   O    1   Write protect EEPROM #1 (0xA8)
- * GPIO15  GPIO   O    0   CPU Run LED !On
- * GPIO16  Alt1   O    x   GMC1TxD0
- * GPIO17  Alt1   O    x   GMC1TxD1
- * GPIO18  Alt1   O    x   GMC1TxD2
- * GPIO19  Alt1   O    x   GMC1TxD3
- * GPIO20  Alt1   I    x   RejectPkt0
- * GPIO21  Alt1   I    x   RejectPkt1
- * GPIO22  GPIO   I    x   PGOOD_DDR
- * GPIO23  Alt1   O    x   SCPD0
- * GPIO24  Alt1   O    x   GMC0TxD2
- * GPIO25  Alt1   O    x   GMC0TxD3
- * GPIO26  GPIO? I/O   x   IIC0SDA (selected in SDR0_PFC4)
- * GPIO27  GPIO   O    0   PHY #0 1000BASE-X select
- * GPIO28  GPIO   O    0   PHY #1 1000BASE-X select
- * GPIO29  GPIO   I    x   Test jumper !Present
- * GPIO30  GPIO   I    x   SFP module #0 !Present
- * GPIO31  GPIO   I    x   SFP module #1 !Present
- *
- * GPIO32  GPIO   O    1   SFP module #0 Tx !Enable
- * GPIO33  GPIO   O    1   SFP module #1 Tx !Enable
- * GPIO34  Alt2   I    x   !UART1_CTS
- * GPIO35  Alt2   O    x   !UART1_RTS
- * GPIO36  Alt1   I    x   !UART0_CTS
- * GPIO37  Alt1   O    x   !UART0_RTS
- * GPIO38  Alt2   O    x   UART1_Tx
- * GPIO39  Alt2   I    x   UART1_Rx
- * GPIO40  Alt1   I    x   IRQ0 (Ethernet 0)
- * GPIO41  Alt1   I    x   IRQ1 (Ethernet 1)
- * GPIO42  Alt1   I    x   IRQ2 (PCI interrupt)
- * GPIO43  Alt1   I    x   IRQ3 (System Alert from CPLD)
- * GPIO44  xxxx   x    x   (grounded through pulldown)
- * GPIO45  GPIO   O    0   PHY #0 Enable
- * GPIO46  GPIO   O    0   PHY #1 Enable
- * GPIO47  GPIO   I    x   Reset switch !Pressed
- * GPIO48  GPIO   I    x   Shutdown switch !Pressed
- * GPIO49  xxxx   x    x   (reserved for trace port)
- *   .      .     .    .               .
- *   .      .     .    .               .
- *   .      .     .    .               .
- * GPIO63  xxxx   x    x   (reserved for trace port)
- */
-
-#define CONFIG_SYS_GPIO_ATMEGA_RESET_	12
-#define CONFIG_SYS_GPIO_ATMEGA_SS_	13
-#define CONFIG_SYS_GPIO_PHY0_FIBER_SEL	27
-#define CONFIG_SYS_GPIO_PHY1_FIBER_SEL	28
-#define CONFIG_SYS_GPIO_SFP0_PRESENT_	30
-#define CONFIG_SYS_GPIO_SFP1_PRESENT_	31
-#define CONFIG_SYS_GPIO_SFP0_TX_EN_	32
-#define CONFIG_SYS_GPIO_SFP1_TX_EN_	33
-#define CONFIG_SYS_GPIO_PHY0_EN	45
-#define CONFIG_SYS_GPIO_PHY1_EN	46
-#define CONFIG_SYS_GPIO_RESET_PRESSED_	47
-
-/*
- * PPC440 GPIO Configuration
- */
-#define CONFIG_SYS_4xx_GPIO_TABLE { /*	  Out		  GPIO	Alternate1	Alternate2	Alternate3 */ \
-{											\
-/* GPIO Core 0 */									\
-{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0	EBC_ADDR(7)	DMA_REQ(2)	*/	\
-{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1	EBC_ADDR(6)	DMA_ACK(2)	*/	\
-{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO2	EBC_ADDR(5)	DMA_EOT/TC(2)	*/	\
-{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO3	EBC_ADDR(4)	DMA_REQ(3)	*/	\
-{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO4	EBC_ADDR(3)	DMA_ACK(3)	*/	\
-{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO5	EBC_ADDR(2)	DMA_EOT/TC(3)	*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6	EBC_CS_N(1)			*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7	EBC_CS_N(2)			*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8	EBC_CS_N(3)			*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9	EBC_CS_N(4)			*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5)			*/	\
-{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR			*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO12				*/	\
-{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO13				*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO14				*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO15				*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO16 GMCTxD(4)			*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO17 GMCTxD(5)			*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO18 GMCTxD(6)			*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO19 GMCTxD(7)			*/	\
-{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 RejectPkt0			*/	\
-{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 RejectPkt1			*/	\
-{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO22				*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 SCPD0				*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO24 GMCTxD(2)			*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO25 GMCTxD(3)			*/	\
-{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26				*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ	USB2D_RXERROR	*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO28		USB2D_TXVALID	*/	\
-{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO29 EBC_EXT_HDLA	USB2D_PAD_SUSPNDM */	\
-{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 EBC_EXT_ACK	USB2D_XCVRSELECT*/	\
-{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO31 EBC_EXR_BUSREQ	USB2D_TERMSELECT*/	\
-},											\
-{											\
-/* GPIO Core 1 */									\
-{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 USB2D_OPMODE0	EBC_DATA(2)	*/	\
-{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 USB2D_OPMODE1	EBC_DATA(3)	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO34 UART0_DCD_N	UART1_DSR_CTS_N	UART2_SOUT*/ \
-{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
-{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0)	UART3_SIN*/ \
-{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO37 UART0_RTS_N	EBC_DATA(1)	UART3_SOUT*/ \
-{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N	UART1_SOUT	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N	UART1_SIN	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0)			*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1)			*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2)			*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3)			*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4)	DMA_ACK(1)	*/	\
-{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6)	DMA_EOT/TC(1)	*/	\
-{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7)	DMA_REQ(0)	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8)	DMA_ACK(0)	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9)	DMA_EOT/TC(0)	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63  Unselect via TraceSelect Bit	*/	\
-}											\
-}
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400 /* speed to run kgdb serial port	*/
-#endif
-
-/* Pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
-#endif /* __CONFIG_H */