summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
authorLawrence R. Johnson <lrj@acm.org>2008-01-03 15:02:02 -0500
committerStefan Roese <sr@denx.de>2008-01-04 11:39:13 +0100
commit0ddd969aec532bd7eae30fc09590488a3aaa629a (patch)
tree769a3324723bdf6d246399368479b8e5021be70b
parentb05e8bf58be9d8956fdfde3d8c8e87c140414663 (diff)
downloadu-boot-imx-0ddd969aec532bd7eae30fc09590488a3aaa629a.zip
u-boot-imx-0ddd969aec532bd7eae30fc09590488a3aaa629a.tar.gz
u-boot-imx-0ddd969aec532bd7eae30fc09590488a3aaa629a.tar.bz2
ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Korat board
Signed-off-by: Larry Johnson <lrj@acm.org>
-rw-r--r--board/korat/korat.c117
-rw-r--r--include/configs/korat.h153
2 files changed, 161 insertions, 109 deletions
diff --git a/board/korat/korat.c b/board/korat/korat.c
index 7cb9ee1..199c1ff 100644
--- a/board/korat/korat.c
+++ b/board/korat/korat.c
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2007
+ * (C) Copyright 2007-2008
* Larry Johnson, lrj@acm.org
*
* (C) Copyright 2006
@@ -26,6 +26,7 @@
*/
#include <common.h>
+#include <asm/gpio.h>
#include <asm/processor.h>
#include <asm-ppc/io.h>
#include <i2c.h>
@@ -40,7 +41,6 @@ ulong flash_get_size(ulong base, int banknum);
int board_early_init_f(void)
{
u32 sdr0_pfc1, sdr0_pfc2;
- u32 gpio0_ir;
u32 reg;
int eth;
@@ -48,102 +48,6 @@ int board_early_init_f(void)
mtdcr(ebccfgd, 0xb8400000);
/*--------------------------------------------------------------------
- * Setup the GPIO pins
- *
- * Korat GPIO usage:
- *
- * Init.
- * Pin Source I/O value Function
- * ------ ------ --- ----- ---------------------------------
- * GPIO00 Alt1 I/O x PerAddr07
- * GPIO01 Alt1 I/O x PerAddr06
- * GPIO02 Alt1 I/O x PerAddr05
- * GPIO03 GPIO x x GPIO03 to expansion bus connector
- * GPIO04 GPIO x x GPIO04 to expansion bus connector
- * GPIO05 GPIO x x GPIO05 to expansion bus connector
- * GPIO06 Alt1 O x PerCS1 (2nd NOR flash)
- * GPIO07 Alt1 O x PerCS2 (CPLD)
- * GPIO08 Alt1 O x PerCS3 to expansion bus connector
- * GPIO09 Alt1 O x PerCS4 to expansion bus connector
- * GPIO10 Alt1 O x PerCS5 to expansion bus connector
- * GPIO11 Alt1 I x PerErr
- * GPIO12 GPIO O 0 ATMega !Reset
- * GPIO13 GPIO O 1 SPI Atmega !SS
- * GPIO14 GPIO O 1 Write protect EEPROM #1 (0xA8)
- * GPIO15 GPIO O 0 CPU Run LED !On
- * GPIO16 Alt1 O x GMC1TxD0
- * GPIO17 Alt1 O x GMC1TxD1
- * GPIO18 Alt1 O x GMC1TxD2
- * GPIO19 Alt1 O x GMC1TxD3
- * GPIO20 Alt1 O x RejectPkt0
- * GPIO21 Alt1 O x RejectPkt1
- * GPIO22 GPIO I x PGOOD_DDR
- * GPIO23 Alt1 O x SCPD0
- * GPIO24 Alt1 O x GMC0TxD2
- * GPIO25 Alt1 O x GMC0TxD3
- * GPIO26 GPIO? I/O x IIC0SDA (selected in SDR0_PFC4)
- * GPIO27 GPIO O 0 PHY #0 1000BASE-X
- * GPIO28 GPIO O 0 PHY #1 1000BASE-X
- * GPIO29 GPIO I x Test jumper !Present
- * GPIO30 GPIO I x SFP module #0 !Present
- * GPIO31 GPIO I x SFP module #1 !Present
- *
- * GPIO32 GPIO O 1 SFP module #0 Tx !Enable
- * GPIO33 GPIO O 1 SFP module #1 Tx !Enable
- * GPIO34 Alt2 I x !UART1_CTS
- * GPIO35 Alt2 O x !UART1_RTS
- * GPIO36 Alt1 I x !UART0_CTS
- * GPIO37 Alt1 O x !UART0_RTS
- * GPIO38 Alt2 O x UART1_Tx
- * GPIO39 Alt2 I x UART1_Rx
- * GPIO40 Alt1 I x IRQ0 (Ethernet 0)
- * GPIO41 Alt1 I x IRQ1 (Ethernet 1)
- * GPIO42 Alt1 I x IRQ2 (PCI interrupt)
- * GPIO43 Alt1 I x IRQ3 (System Alert from CPLD)
- * GPIO44 xxxx x x (grounded through pulldown)
- * GPIO45 GPIO O 0 PHY #0 Enable
- * GPIO46 GPIO O 0 PHY #1 Enable
- * GPIO47 GPIO I x Reset switch !Pressed
- * GPIO48 GPIO I x Shutdown switch !Pressed
- * GPIO49 xxxx x x (reserved for trace port)
- * . . . . .
- * . . . . .
- * . . . . .
- * GPIO63 xxxx x x (reserved for trace port)
- *-------------------------------------------------------------------*/
-
- out_be32((u32 *) GPIO0_OR, 0x00060000);
- out_be32((u32 *) GPIO1_OR, 0xC0000000);
-
- out_be32((u32 *) GPIO0_OSRL, 0x54055400);
- out_be32((u32 *) GPIO0_OSRH, 0x55015000);
- out_be32((u32 *) GPIO1_OSRL, 0x02180000);
- out_be32((u32 *) GPIO1_OSRH, 0x00000000);
-
- out_be32((u32 *) GPIO0_TSRL, 0x54055500);
- out_be32((u32 *) GPIO0_TSRH, 0x00015000);
- out_be32((u32 *) GPIO1_TSRL, 0x00000000);
- out_be32((u32 *) GPIO1_TSRH, 0x00000000);
-
- out_be32((u32 *) GPIO0_TCR, 0x000FF0D8);
- out_be32((u32 *) GPIO1_TCR, 0xD6060000);
-
- out_be32((u32 *) GPIO0_ISR1L, 0x54000100);
- out_be32((u32 *) GPIO0_ISR1H, 0x00500000);
- out_be32((u32 *) GPIO1_ISR1L, 0x00405500);
- out_be32((u32 *) GPIO1_ISR1H, 0x00000000);
-
- out_be32((u32 *) GPIO0_ISR2L, 0x00000000);
- out_be32((u32 *) GPIO0_ISR2H, 0x00000000);
- out_be32((u32 *) GPIO1_ISR2L, 0x04010000);
- out_be32((u32 *) GPIO1_ISR2H, 0x00000000);
-
- out_be32((u32 *) GPIO0_ISR3L, 0x00000000);
- out_be32((u32 *) GPIO0_ISR3H, 0x00000000);
- out_be32((u32 *) GPIO1_ISR3L, 0x00000000);
- out_be32((u32 *) GPIO1_ISR3H, 0x00000000);
-
- /*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
*-------------------------------------------------------------------*/
mtdcr(uic0sr, 0xffffffff); /* clear all */
@@ -176,9 +80,8 @@ int board_early_init_f(void)
/* Configure the two Ethernet PHYs. For each PHY, configure for fiber
* if the SFP module is present, and for copper if it is not present.
*/
- gpio0_ir = in_be32((u32 *) GPIO0_IR);
for (eth = 0; eth < 2; ++eth) {
- if (gpio0_ir & (0x00000001 << (1 - eth))) {
+ if (gpio_read_in_bit(CFG_GPIO_SFP0_PRESENT_ + eth)) {
/* SFP module not present: configure PHY for copper. */
/* Set PHY to autonegotate 10 MB, 100MB, or 1 GB */
out_8((u8 *) CFG_CPLD_BASE + 0x06,
@@ -187,14 +90,13 @@ int board_early_init_f(void)
} else {
/* SFP module present: configure PHY for fiber and
enable output */
- out_be32((u32 *) GPIO0_OR, in_be32((u32 *) GPIO0_OR) |
- (0x00000001 << (4 - eth)));
- out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) &
- ~(0x00000001 << (31 - eth)));
+ gpio_write_bit(CFG_GPIO_PHY0_FIBER_SEL + eth, 1);
+ gpio_write_bit(CFG_GPIO_SFP0_TX_EN_ + eth, 0);
}
}
/* enable Ethernet: set GPIO45 and GPIO46 to 1 */
- out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) | 0x00060000);
+ gpio_write_bit(CFG_GPIO_PHY0_EN, 1);
+ gpio_write_bit(CFG_GPIO_PHY1_EN, 1);
/* select Ethernet pins */
mfsdr(SDR0_PFC1, sdr0_pfc1);
@@ -525,20 +427,19 @@ int checkboard(void)
{
char const *const s = getenv("serial#");
u8 const rev = in_8((u8 *) CFG_CPLD_BASE + 0);
- u32 const gpio0_or = in_be32((u32 *) GPIO0_OR);
printf("Board: Korat, Rev. %X", rev);
if (s != NULL)
printf(", serial# %s", s);
printf(", Ethernet PHY 0: ");
- if (gpio0_or & 0x00000010)
+ if (gpio_read_out_bit(CFG_GPIO_PHY0_FIBER_SEL))
printf("fiber");
else
printf("copper");
printf(", PHY 1: ");
- if (gpio0_or & 0x00000008)
+ if (gpio_read_out_bit(CFG_GPIO_PHY1_FIBER_SEL))
printf("fiber");
else
printf("copper");
diff --git a/include/configs/korat.h b/include/configs/korat.h
index 1ea7d48..7d0640b 100644
--- a/include/configs/korat.h
+++ b/include/configs/korat.h
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2007
+ * (C) Copyright 2007-2008
* Larry Johnson, lrj@acm.org
*
* (C) Copyright 2006-2007
@@ -361,6 +361,157 @@
#define CFG_EBC_PB2AP 0x04017300
#define CFG_EBC_PB2CR (CFG_CPLD_BASE | 0x00038000)
+/*-----------------------------------------------------------------------
+ * GPIO Setup
+ *
+ * Korat GPIO usage:
+ *
+ * Init.
+ * Pin Source I/O value Function
+ * ------ ------ --- ----- ---------------------------------
+ * GPIO00 Alt1 I/O x PerAddr07
+ * GPIO01 Alt1 I/O x PerAddr06
+ * GPIO02 Alt1 I/O x PerAddr05
+ * GPIO03 GPIO x x GPIO03 to expansion bus connector
+ * GPIO04 GPIO x x GPIO04 to expansion bus connector
+ * GPIO05 GPIO x x GPIO05 to expansion bus connector
+ * GPIO06 Alt1 O x PerCS1 (2nd NOR flash)
+ * GPIO07 Alt1 O x PerCS2 (CPLD)
+ * GPIO08 Alt1 O x PerCS3 to expansion bus connector
+ * GPIO09 Alt1 O x PerCS4 to expansion bus connector
+ * GPIO10 Alt1 O x PerCS5 to expansion bus connector
+ * GPIO11 Alt1 I x PerErr
+ * GPIO12 GPIO O 0 ATMega !Reset
+ * GPIO13 GPIO O 1 SPI Atmega !SS
+ * GPIO14 GPIO O 1 Write protect EEPROM #1 (0xA8)
+ * GPIO15 GPIO O 0 CPU Run LED !On
+ * GPIO16 Alt1 O x GMC1TxD0
+ * GPIO17 Alt1 O x GMC1TxD1
+ * GPIO18 Alt1 O x GMC1TxD2
+ * GPIO19 Alt1 O x GMC1TxD3
+ * GPIO20 Alt1 I x RejectPkt0
+ * GPIO21 Alt1 I x RejectPkt1
+ * GPIO22 GPIO I x PGOOD_DDR
+ * GPIO23 Alt1 O x SCPD0
+ * GPIO24 Alt1 O x GMC0TxD2
+ * GPIO25 Alt1 O x GMC0TxD3
+ * GPIO26 GPIO? I/O x IIC0SDA (selected in SDR0_PFC4)
+ * GPIO27 GPIO O 0 PHY #0 1000BASE-X select
+ * GPIO28 GPIO O 0 PHY #1 1000BASE-X select
+ * GPIO29 GPIO I x Test jumper !Present
+ * GPIO30 GPIO I x SFP module #0 !Present
+ * GPIO31 GPIO I x SFP module #1 !Present
+ *
+ * GPIO32 GPIO O 1 SFP module #0 Tx !Enable
+ * GPIO33 GPIO O 1 SFP module #1 Tx !Enable
+ * GPIO34 Alt2 I x !UART1_CTS
+ * GPIO35 Alt2 O x !UART1_RTS
+ * GPIO36 Alt1 I x !UART0_CTS
+ * GPIO37 Alt1 O x !UART0_RTS
+ * GPIO38 Alt2 O x UART1_Tx
+ * GPIO39 Alt2 I x UART1_Rx
+ * GPIO40 Alt1 I x IRQ0 (Ethernet 0)
+ * GPIO41 Alt1 I x IRQ1 (Ethernet 1)
+ * GPIO42 Alt1 I x IRQ2 (PCI interrupt)
+ * GPIO43 Alt1 I x IRQ3 (System Alert from CPLD)
+ * GPIO44 xxxx x x (grounded through pulldown)
+ * GPIO45 GPIO O 0 PHY #0 Enable
+ * GPIO46 GPIO O 0 PHY #1 Enable
+ * GPIO47 GPIO I x Reset switch !Pressed
+ * GPIO48 GPIO I x Shutdown switch !Pressed
+ * GPIO49 xxxx x x (reserved for trace port)
+ * . . . . .
+ * . . . . .
+ * . . . . .
+ * GPIO63 xxxx x x (reserved for trace port)
+*----------------------------------------------------------------------*/
+
+#define CFG_GPIO_ATMEGA_SS_ 13
+#define CFG_GPIO_PHY0_FIBER_SEL 27
+#define CFG_GPIO_PHY1_FIBER_SEL 28
+#define CFG_GPIO_SFP0_PRESENT_ 30
+#define CFG_GPIO_SFP1_PRESENT_ 31
+#define CFG_GPIO_SFP0_TX_EN_ 32
+#define CFG_GPIO_SFP1_TX_EN_ 33
+#define CFG_GPIO_PHY0_EN 45
+#define CFG_GPIO_PHY1_EN 46
+
+/*-----------------------------------------------------------------------
+ * PPC440 GPIO Configuration
+ */
+#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+{ \
+/* GPIO Core 0 */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \
+{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \
+{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \
+{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO13 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO14 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO15 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO16 GMCTxD(4) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO17 GMCTxD(5) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO18 GMCTxD(6) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO19 GMCTxD(7) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 SCPD0 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO24 GMCTxD(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO25 GMCTxD(3) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 USB2D_TXVALID */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \
+}, \
+{ \
+/* GPIO Core 1 */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0) UART3_SIN*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
+} \
+}
+
/*
* Internal Definitions
*