Patches by Dave Ellis, 18 Mar 2003 for SXNI855T board:

- fix SRAM and SDRAM memory sizing
- add status LED support
- add MAC address for second (SCC1) ethernet port

Update default environment for TQM8260 board

5 files changed, 105 insertions, 29 deletions

diff --git a/CHANGELOG b/CHANGELOG
index 2fa9a94..d28fef0 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,13 @@
 Changes since U-Boot 0.2.2:
 ======================================================================
 
+* Patches by Dave Ellis, 18 Mar 2003 for SXNI855T board:
+  - fix SRAM and SDRAM memory sizing
+  - add status LED support
+  - add MAC address for second (SCC1) ethernet port
+
+* Update default environment for TQM8260 board
+
 * Patch by Rick Bronson, 16 Mar 2003:
   - Add NAND flash support for reading, writing, and erasing NAND
     flash (certain forms of which are called SmartMedia).
diff --git a/board/sixnet/sixnet.c b/board/sixnet/sixnet.c
index c65e809..1570c46 100644
--- a/board/sixnet/sixnet.c
+++ b/board/sixnet/sixnet.c
@@ -28,6 +28,9 @@
 #include <net.h>	/* for eth_init() */
 #include <rtc.h>
 #include "sixnet.h"
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+# include <status_led.h>
+#endif
 
 #define ORMASK(size) ((-size) & OR_AM_MSK)
 
@@ -35,6 +38,22 @@ static long ram_size(ulong *, long);
 
 /* ------------------------------------------------------------------------- */
 
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+void show_boot_progress (int status)
+{
+#if defined(CONFIG_STATUS_LED)
+# if defined(STATUS_LED_BOOT)
+	if (status == 15) {
+		/* ready to transfer to kernel, make sure LED is proper state */
+		status_led_set(STATUS_LED_BOOT, CONFIG_BOOT_LED_STATE);
+	}
+# endif /* STATUS_LED_BOOT */
+#endif /* CONFIG_STATUS_LED */
+}
+#endif
+
+/* ------------------------------------------------------------------------- */
+
 /*
  * Check Board Identity:
  * returns 0 if recognized, -1 if unknown
@@ -235,6 +254,9 @@ int misc_init_r (void)
 
 	volatile immap_t     *immap = (immap_t *)CFG_IMMR;
 	volatile memctl8xx_t *memctl = &immap->im_memctl;
+	char* s;
+	char* e;
+	int reg;
 	bd_t *bd = gd->bd;
 
 	memctl->memc_or2 = NVRAM_OR_PRELIM;
@@ -283,18 +305,19 @@ int misc_init_r (void)
 	    immap->im_sit.sit_rtc = tim;
 	}
 
-#if 0
-	/* The code below is no longer valid since the prototype of
-	 * eth_init() and eth_halt() have been changed to support
-	 * multi-ethernet feature in U-Boot; the eth_initialize()
-	 * routine should be called before any access to the ethernet
-	 * callbacks.
+	/* set up ethernet address for SCC ethernet. If eth1addr
+	 * is present it gets a unique address, otherwise it
+	 * shares the FEC address.
 	 */
+	s = getenv("eth1addr");
+	if (s == NULL)
+		s = getenv("ethaddr");
+	for (reg=0; reg<6; ++reg) {
+		bd->bi_enet1addr[reg] = s ? simple_strtoul(s, &e, 16) : 0;
+		if (s)
+			s = (*e) ? e+1 : e;
+	}
 
-	/* FIXME - for now init ethernet to force PHY special mode */
-	eth_init(bd);
-	eth_halt();
-#endif
 	return (0);
 }
 
@@ -307,7 +330,7 @@ int misc_init_r (void)
  *
  * The memory size MUST be a power of 2 for this to work.
  *
- * The only memory modified is 4 bytes at offset 0. This is important
+ * The only memory modified is 8 bytes at offset 0. This is important
  * since for the SRAM this location is reserved for autosizing, so if
  * it is modified and the board is reset before ram_size() completes
  * no damage is  done. Normally even the memory at 0 is preserved. The
@@ -319,28 +342,27 @@ static long ram_size(ulong *base, long maxsize)
 {
     volatile long	*test_addr;
     volatile long	*base_addr = base;
-    volatile long	*flash = (volatile long*)CFG_FLASH_BASE;
     ulong		ofs;		/* byte offset from base_addr */
     ulong		save;		/* to make test non-destructive */
-    ulong		junk;
+    ulong		save2;		/* to make test non-destructive */
     long		ramsize = -1;	/* size not determined yet */
 
     save = *base_addr;		/* save value at 0 so can restore */
+    save2 = *(base_addr+1);	/* save value at 4 so can restore */
 
     /* is any SRAM present? */
     *base_addr = 0x5555aaaa;
 
-    /* use flash read to modify data bus, since with no SRAM present
-     * the data bus may retain the value if our code is running
-     * completely in the cache.
+    /* It is important to drive the data bus with different data so
+     * it doesn't remember the value and look like RAM that isn't there.
      */
-    junk = *flash;
+    *(base_addr + 1) = 0xaaaa5555;	/* use write to modify data bus */
 
     if (*base_addr != 0x5555aaaa)
 	ramsize = 0;		/* no RAM present, or defective */
     else {
 	*base_addr = 0xaaaa5555;
-	junk = *flash;		/* use flash read to modify data bus */
+        *(base_addr + 1) = 0x5555aaaa;	/* use write to modify data bus */
 	if (*base_addr != 0xaaaa5555)
 	    ramsize = 0;	/* no RAM present, or defective */
     }
@@ -355,6 +377,7 @@ static long ram_size(ulong *base, long maxsize)
     }
 
     *base_addr = save;		/* restore value at 0 */
+    *(base_addr+1) = save2;	/* restore value at 4 */
     return (ramsize);
 }
 
@@ -426,18 +449,21 @@ const uint sdram_table[] =
 			  MCR_MLCF(2) | MCR_MAD(0x30))	/* twice at 0x30  */
 
 /* MAMR values work in either mamr or mbmr */
-/* 8 column SDRAM */
-#define SDRAM_MAMR_8COL  /* refresh at 50MHz */				  \
+#define SDRAM_MAMR_BASE  /* refresh at 50MHz */				  \
 			 ((195 << MAMR_PTA_SHIFT) | MAMR_PTAE		  \
-			 | MAMR_AMA_TYPE_0	/* Address MUX 0 */	  \
 			 | MAMR_DSA_1_CYCL	/* 1 cycle disable */	  \
-			 | MAMR_G0CLA_A11	/* GPL0 A11[MPC] */	  \
 			 | MAMR_RLFA_1X		/* Read loop 1 time */	  \
 			 | MAMR_WLFA_1X		/* Write loop 1 time */	  \
 			 | MAMR_TLFA_4X)	/* Timer loop 4 times */
+/* 8 column SDRAM */
+#define SDRAM_MAMR_8COL	(SDRAM_MAMR_BASE				  \
+			 | MAMR_AMA_TYPE_0	/* Address MUX 0 */	  \
+			 | MAMR_G0CLA_A11)	/* GPL0 A11[MPC] */
 
 /* 9 column SDRAM */
-#define SDRAM_MAMR_9COL ((SDRAM_MAMR_8COL & (~MAMR_G0CLA_A11)) | MAMR_G0CLA_A10)
+#define SDRAM_MAMR_9COL	(SDRAM_MAMR_BASE				  \
+			 | MAMR_AMA_TYPE_1	/* Address MUX 1 */	  \
+			 | MAMR_G0CLA_A10)	/* GPL0 A10[MPC] */
 
 /* base address 0, 32-bit port, SDRAM UPM, valid */
 #define SDRAM_BR_VALUE   (BR_PS_32 | BR_MS_UPMA | BR_V)
diff --git a/include/asm-ppc/u-boot.h b/include/asm-ppc/u-boot.h
index e417e0d..78744e2 100644
--- a/include/asm-ppc/u-boot.h
+++ b/include/asm-ppc/u-boot.h
@@ -68,7 +68,10 @@ typedef struct bd_info {
 #if defined(CONFIG_HYMOD)
 	hymod_conf_t	bi_hymod_conf;	/* hymod configuration information */
 #endif
-#if defined(CONFIG_EVB64260) || defined(CONFIG_PN62) || defined(CONFIG_SVM_SC8xx)
+#if defined(CONFIG_EVB64260)	|| \
+    defined(CONFIG_PN62)	|| \
+    defined(CONFIG_SXNI855T)	|| \
+    defined(CONFIG_SVM_SC8xx)
 	/* second onboard ethernet port */
 	unsigned char   bi_enet1addr[6];
 #endif
diff --git a/include/configs/SXNI855T.h b/include/configs/SXNI855T.h
index 8725f27..a7f0c21 100644
--- a/include/configs/SXNI855T.h
+++ b/include/configs/SXNI855T.h
@@ -81,6 +81,32 @@
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 #endif
 
+/*-----------------------------------------------------------------------
+ * Definitions for status LED
+ */
+#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
+
+# define STATUS_LED_PAR		im_ioport.iop_papar
+# define STATUS_LED_DIR		im_ioport.iop_padir
+# define STATUS_LED_ODR		im_ioport.iop_paodr
+# define STATUS_LED_DAT		im_ioport.iop_padat
+
+# define STATUS_LED_BIT		0x8000		/* LED 0 is on PA.0 */
+# define STATUS_LED_PERIOD	((CFG_HZ / 2) / 5)	/* blink at 5 Hz */
+# define STATUS_LED_STATE	STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE	0		/* LED on for bit == 0	*/
+
+# define STATUS_LED_BOOT	0		/* LED 0 used for boot status */
+
+#ifdef DEV	/* development (debug) settings */
+#define CONFIG_BOOT_LED_STATE	STATUS_LED_OFF
+#else		/* production settings */
+#define CONFIG_BOOT_LED_STATE	STATUS_LED_ON
+#endif
+
+#define CONFIG_SHOW_BOOT_PROGRESS 1
+
 #define CONFIG_BOOTCOMMAND	"bootm f8040000 f8100000" /* autoboot command */
 #define CONFIG_BOOTARGS		"root=/dev/ram ip=off"
 
diff --git a/include/configs/TQM8260.h b/include/configs/TQM8260.h
index 9972312..3dd6714 100644
--- a/include/configs/TQM8260.h
+++ b/include/configs/TQM8260.h
@@ -69,11 +69,25 @@
 #define CONFIG_PREBOOT	"echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
 
 #undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND							\
-	"bootp; " 								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " 	\
-	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " 	\
-	"bootm"
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=$(serverip):$(rootpath)\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs $(bootargs) "				\
+		"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"	\
+		":$(hostname):$(netdev):off panic=1\0"			\
+	"flash_nfs=run nfsargs addip;"					\
+		"bootm $(kernel_addr)\0"				\
+	"flash_self=run ramargs addip;"					\
+		"bootm $(kernel_addr) $(ramdisk_addr)\0"		\
+	"net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0"	\
+	"rootpath=/opt/eldk/ppc_82xx\0"					\
+	"bootfile=/tftpboot/TQM8260/uImage\0"				\
+	"kernel_addr=40040000\0"					\
+	"ramdisk_addr=40100000\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
 
 /* enable I2C and select the hardware/software driver */
 #undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/