ENGR00211117 - U-Boot: Add EPDC splash screen for MX 6DL/S platforms

- EPDC Splash support for MX6DL/S Sabre SD
- EPDC Splash support for MX6DL/S ARM2
- Currently, splash screen consists of a simple black border
around a white screen.  Done this way to save in memory footprint.

Signed-off-by: Danny Nold <dannynold@freescale.com>

5 files changed, 653 insertions, 10 deletions

diff --git a/board/freescale/mx6q_arm2/mx6q_arm2.c b/board/freescale/mx6q_arm2/mx6q_arm2.c
index d78c704..4e189d8 100644
--- a/board/freescale/mx6q_arm2/mx6q_arm2.c
+++ b/board/freescale/mx6q_arm2/mx6q_arm2.c
@@ -38,9 +38,13 @@
 #include <linux/fb.h>
 #include <linux/mxcfb.h>
 #include <ipu.h>
+#endif
+#if defined(CONFIG_VIDEO_MX5) || defined(CONFIG_MXC_EPDC)
 #include <lcd.h>
 #endif
 
+#include "../../../drivers/video/mxc_epdc_fb.h"
+
 #ifdef CONFIG_IMX_ECSPI
 #include <imx_spi.h>
 #endif
@@ -737,6 +741,294 @@ int board_mmc_init(bd_t *bis)
 		return -1;
 }
 
+#ifdef CONFIG_MXC_EPDC
+#ifdef CONFIG_SPLASH_SCREEN
+int setup_splash_img()
+{
+#ifdef CONFIG_SPLASH_IS_IN_MMC
+	int mmc_dev = get_mmc_env_devno();
+	ulong offset = CONFIG_SPLASH_IMG_OFFSET;
+	ulong size = CONFIG_SPLASH_IMG_SIZE;
+	ulong addr = 0;
+	char *s = NULL;
+	struct mmc *mmc = find_mmc_device(mmc_dev);
+	uint blk_start, blk_cnt, n;
+
+	s = getenv("splashimage");
+
+	if (NULL == s) {
+		puts("env splashimage not found!\n");
+		return -1;
+	}
+	addr = simple_strtoul(s, NULL, 16);
+
+	if (!mmc) {
+		printf("MMC Device %d not found\n",
+			mmc_dev);
+		return -1;
+	}
+
+	if (mmc_init(mmc)) {
+		puts("MMC init failed\n");
+		return  -1;
+	}
+
+	blk_start = ALIGN(offset, mmc->read_bl_len) / mmc->read_bl_len;
+	blk_cnt   = ALIGN(size, mmc->read_bl_len) / mmc->read_bl_len;
+	n = mmc->block_dev.block_read(mmc_dev, blk_start,
+					blk_cnt, (u_char *)addr);
+	flush_cache((ulong)addr, blk_cnt * mmc->read_bl_len);
+
+	return (n == blk_cnt) ? 0 : -1;
+#endif
+}
+#endif
+
+vidinfo_t panel_info = {
+	.vl_refresh = 85,
+	.vl_col = 800,
+	.vl_row = 600,
+	.vl_pixclock = 26666667,
+	.vl_left_margin = 8,
+	.vl_right_margin = 100,
+	.vl_upper_margin = 4,
+	.vl_lower_margin = 8,
+	.vl_hsync = 4,
+	.vl_vsync = 1,
+	.vl_sync = 0,
+	.vl_mode = 0,
+	.vl_flag = 0,
+	.vl_bpix = 3,
+	cmap:0,
+};
+
+struct epdc_timing_params panel_timings = {
+	.vscan_holdoff = 4,
+	.sdoed_width = 10,
+	.sdoed_delay = 20,
+	.sdoez_width = 10,
+	.sdoez_delay = 20,
+	.gdclk_hp_offs = 419,
+	.gdsp_offs = 20,
+	.gdoe_offs = 0,
+	.gdclk_offs = 5,
+	.num_ce = 1,
+};
+
+static void setup_epdc_power()
+{
+	unsigned int reg;
+
+	/* Setup epdc voltage */
+
+	/* EIM_A17 - GPIO2[21] for PWR_GOOD status */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A17__GPIO_2_21);
+
+	/* EIM_D17 - GPIO3[17] for VCOM control */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D17__GPIO_3_17);
+
+	/* Set as output */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_GDIR);
+	reg |= (1 << 17);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_GDIR);
+
+	/* EIM_D20 - GPIO3[20] for EPD PMIC WAKEUP */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D20__GPIO_3_20);
+	/* Set as output */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_GDIR);
+	reg |= (1 << 20);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_GDIR);
+
+	/* EIM_A18 - GPIO2[20] for EPD PWR CTL0 */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A18__GPIO_2_20);
+	/* Set as output */
+	reg = readl(GPIO2_BASE_ADDR + GPIO_GDIR);
+	reg |= (1 << 20);
+	writel(reg, GPIO2_BASE_ADDR + GPIO_GDIR);
+}
+
+unsigned int g_pgood_1, g_pgood_2, g_pgood_3;
+void epdc_power_on()
+{
+	unsigned int reg;
+
+	g_pgood_1 = readl(GPIO2_BASE_ADDR + GPIO_DR);
+
+	/* Set EPD_PWR_CTL0 to high - enable EINK_VDD (3.15) */
+	reg = readl(GPIO2_BASE_ADDR + GPIO_DR);
+	reg |= (1 << 20);
+	writel(reg, GPIO2_BASE_ADDR + GPIO_DR);
+
+	/* Set PMIC Wakeup to high - enable Display power */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+	reg |= (1 << 20);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+
+	g_pgood_2 = readl(GPIO2_BASE_ADDR + GPIO_DR);
+		udelay(1000000);
+	g_pgood_3 = readl(GPIO2_BASE_ADDR + GPIO_DR);
+return;
+	/* Wait for PWRGOOD == 1 */
+	while (1) {
+		reg = readl(GPIO2_BASE_ADDR + GPIO_DR);
+		if (!(reg & (1 << 21)))
+			break;
+
+		udelay(100);
+	}
+
+	/* Enable VCOM */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+	reg |= (1 << 17);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+
+	reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+
+	udelay(500);
+}
+
+void  epdc_power_off()
+{
+	unsigned int reg;
+	/* Set PMIC Wakeup to low - disable Display power */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+	reg &= ~(1 << 20);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+
+	/* Disable VCOM */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+	reg &= ~(1 << 17);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+
+	/* Set EPD_PWR_CTL0 to low - disable EINK_VDD (3.15) */
+	reg = readl(GPIO2_BASE_ADDR + GPIO_DR);
+	reg &= ~(1 << 20);
+	writel(reg, GPIO2_BASE_ADDR + GPIO_DR);
+}
+
+int setup_waveform_file()
+{
+#ifdef CONFIG_WAVEFORM_FILE_IN_MMC
+	int mmc_dev = get_mmc_env_devno();
+	ulong offset = CONFIG_WAVEFORM_FILE_OFFSET;
+	ulong size = CONFIG_WAVEFORM_FILE_SIZE;
+	ulong addr = CONFIG_WAVEFORM_BUF_ADDR;
+	char *s = NULL;
+	struct mmc *mmc = find_mmc_device(mmc_dev);
+	uint blk_start, blk_cnt, n;
+
+	if (!mmc) {
+		printf("MMC Device %d not found\n",
+			mmc_dev);
+		return -1;
+	}
+
+	if (mmc_init(mmc)) {
+		puts("MMC init failed\n");
+		return -1;
+	}
+
+	blk_start = ALIGN(offset, mmc->read_bl_len) / mmc->read_bl_len;
+	blk_cnt   = ALIGN(size, mmc->read_bl_len) / mmc->read_bl_len;
+	n = mmc->block_dev.block_read(mmc_dev, blk_start,
+		blk_cnt, (u_char *)addr);
+	flush_cache((ulong)addr, blk_cnt * mmc->read_bl_len);
+
+	return (n == blk_cnt) ? 0 : -1;
+#else
+	return -1;
+#endif
+}
+
+static void setup_epdc()
+{
+	unsigned int reg;
+
+	/* epdc iomux settings */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A16__EPDC_SDDO_0);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA10__EPDC_SDDO_1);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA12__EPDC_SDDO_2);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA11__EPDC_SDDO_3);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_LBA__EPDC_SDDO_4);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_EB2__EPDC_SDDO_5);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_CS0__EPDC_SDDO_6);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_RW__EPDC_SDDO_7);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A21__EPDC_GDCLK);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A22__EPDC_GDSP);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A23__EPDC_GDOE);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A24__EPDC_GDRL);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D31__EPDC_SDCLK);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D27__EPDC_SDOE);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA1__EPDC_SDLE);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_EB1__EPDC_SDSHR);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA2__EPDC_BDR_0);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA4__EPDC_SDCE_0);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA5__EPDC_SDCE_1);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA6__EPDC_SDCE_2);
+
+	/*** epdc Maxim PMIC settings ***/
+
+	/* EPDC PWRSTAT - GPIO2[21] for PWR_GOOD status */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A17__GPIO_2_21);
+
+	/* EPDC VCOM0 - GPIO3[17] for VCOM control */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D17__GPIO_3_17);
+
+	/* UART4 TXD - GPIO3[20] for EPD PMIC WAKEUP */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D20__GPIO_3_20);
+
+	/* EIM_A18 - GPIO2[20] for EPD PWR CTL0 */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A18__GPIO_2_20);
+
+	/*** Set pixel clock rates for EPDC ***/
+
+	/* EPDC AXI clk (IPU2_CLK) from PFD_400M, set to 396/2 = 198MHz */
+	reg = readl(CCM_BASE_ADDR + CLKCTL_CSCDR3);
+	reg &= ~0x7C000;
+	reg |= (1 << 16) | (1 << 14);
+	writel(reg, CCM_BASE_ADDR + CLKCTL_CSCDR3);
+
+	/* EPDC AXI clk enable */
+	reg = readl(CCM_BASE_ADDR + CLKCTL_CCGR3);
+	reg |= 0x00C0;
+	writel(reg, CCM_BASE_ADDR + CLKCTL_CCGR3);
+
+	/* EPDC PIX clk (IPU2_DI1_CLK) from PLL5, set to 650/4/6 = ~27MHz */
+	reg = readl(CCM_BASE_ADDR + CLKCTL_CSCDR2);
+	reg &= ~0x3FE00;
+	reg |= (2 << 15) | (5 << 12);
+	writel(reg, CCM_BASE_ADDR + CLKCTL_CSCDR2);
+
+	/* EPDC PIX clk enable */
+	reg = readl(CCM_BASE_ADDR + CLKCTL_CCGR3);
+	reg |= 0x0C00;
+	writel(reg, CCM_BASE_ADDR + CLKCTL_CCGR3);
+
+	/* PLL5 enable (defaults to 650) */
+	reg = readl(ANATOP_BASE_ADDR + ANATOP_PLL_VIDEO);
+	reg &= ~((1 << 16) | (1 << 12));
+	reg |= (1 << 13);
+	writel(reg, ANATOP_BASE_ADDR + ANATOP_PLL_VIDEO);
+
+	panel_info.epdc_data.working_buf_addr = CONFIG_WORKING_BUF_ADDR;
+	panel_info.epdc_data.waveform_buf_addr = CONFIG_WAVEFORM_BUF_ADDR;
+
+	panel_info.epdc_data.wv_modes.mode_init = 0;
+	panel_info.epdc_data.wv_modes.mode_du = 1;
+	panel_info.epdc_data.wv_modes.mode_gc4 = 3;
+	panel_info.epdc_data.wv_modes.mode_gc8 = 2;
+	panel_info.epdc_data.wv_modes.mode_gc16 = 2;
+	panel_info.epdc_data.wv_modes.mode_gc32 = 2;
+
+	panel_info.epdc_data.epdc_timings = panel_timings;
+
+	setup_epdc_power();
+
+	/* Assign fb_base */
+	gd->fb_base = CONFIG_FB_BASE;
+}
+#endif
+
 /* For DDR mode operation, provide target delay parameter for each SD port.
  * Use cfg->esdhc_base to distinguish the SD port #. The delay for each port
  * is dependent on signal layout for that particular port.  If the following
@@ -752,6 +1044,7 @@ u32 get_ddr_delay(struct fsl_esdhc_cfg *cfg)
 
 #endif
 
+#ifndef CONFIG_MXC_EPDC
 #ifdef CONFIG_LCD
 void lcd_enable(void)
 {
@@ -853,6 +1146,7 @@ void setup_splash_image(void)
 	}
 }
 #endif
+#endif /* !CONFIG_MXC_EPDC */
 
 int board_init(void)
 {
@@ -890,6 +1184,10 @@ int board_init(void)
 #ifdef CONFIG_NAND_GPMI
 	setup_gpmi_nand();
 #endif
+
+#ifdef CONFIG_MXC_EPDC
+	setup_epdc();
+#endif
 	return 0;
 }
 
diff --git a/board/freescale/mx6q_sabresd/mx6q_sabresd.c b/board/freescale/mx6q_sabresd/mx6q_sabresd.c
index b91219a..ceb6c46 100644
--- a/board/freescale/mx6q_sabresd/mx6q_sabresd.c
+++ b/board/freescale/mx6q_sabresd/mx6q_sabresd.c
@@ -31,14 +31,19 @@
 #ifdef CONFIG_MXC_FEC
 #include <miiphy.h>
 #endif
+
 #if defined(CONFIG_VIDEO_MX5)
 #include <linux/list.h>
 #include <linux/fb.h>
 #include <linux/mxcfb.h>
 #include <ipu.h>
+#endif
+#if defined(CONFIG_VIDEO_MX5) || defined(CONFIG_MXC_EPDC)
 #include <lcd.h>
 #endif
 
+#include "../../../drivers/video/mxc_epdc_fb.h"
+
 #ifdef CONFIG_IMX_ECSPI
 #include <imx_spi.h>
 #endif
@@ -1024,6 +1029,287 @@ int board_mmc_init(bd_t *bis)
 		return -1;
 }
 
+#ifdef CONFIG_MXC_EPDC
+#ifdef CONFIG_SPLASH_SCREEN
+int setup_splash_img()
+{
+#ifdef CONFIG_SPLASH_IS_IN_MMC
+	int mmc_dev = get_mmc_env_devno();
+	ulong offset = CONFIG_SPLASH_IMG_OFFSET;
+	ulong size = CONFIG_SPLASH_IMG_SIZE;
+	ulong addr = 0;
+	char *s = NULL;
+	struct mmc *mmc = find_mmc_device(mmc_dev);
+	uint blk_start, blk_cnt, n;
+
+	s = getenv("splashimage");
+
+	if (NULL == s) {
+		puts("env splashimage not found!\n");
+		return -1;
+	}
+	addr = simple_strtoul(s, NULL, 16);
+
+	if (!mmc) {
+		printf("MMC Device %d not found\n",
+			mmc_dev);
+		return -1;
+	}
+
+	if (mmc_init(mmc)) {
+		puts("MMC init failed\n");
+		return  -1;
+	}
+
+	blk_start = ALIGN(offset, mmc->read_bl_len) / mmc->read_bl_len;
+	blk_cnt   = ALIGN(size, mmc->read_bl_len) / mmc->read_bl_len;
+	n = mmc->block_dev.block_read(mmc_dev, blk_start,
+					blk_cnt, (u_char *)addr);
+	flush_cache((ulong)addr, blk_cnt * mmc->read_bl_len);
+
+	return (n == blk_cnt) ? 0 : -1;
+#endif
+}
+#endif
+
+vidinfo_t panel_info = {
+	.vl_refresh = 85,
+	.vl_col = 800,
+	.vl_row = 600,
+	.vl_pixclock = 26666667,
+	.vl_left_margin = 8,
+	.vl_right_margin = 100,
+	.vl_upper_margin = 4,
+	.vl_lower_margin = 8,
+	.vl_hsync = 4,
+	.vl_vsync = 1,
+	.vl_sync = 0,
+	.vl_mode = 0,
+	.vl_flag = 0,
+	.vl_bpix = 3,
+	cmap:0,
+};
+
+struct epdc_timing_params panel_timings = {
+	.vscan_holdoff = 4,
+	.sdoed_width = 10,
+	.sdoed_delay = 20,
+	.sdoez_width = 10,
+	.sdoez_delay = 20,
+	.gdclk_hp_offs = 419,
+	.gdsp_offs = 20,
+	.gdoe_offs = 0,
+	.gdclk_offs = 5,
+	.num_ce = 1,
+};
+
+static void setup_epdc_power()
+{
+	unsigned int reg;
+
+	/* Setup epdc voltage */
+
+	/* EIM_A17 - GPIO2[21] for PWR_GOOD status */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A17__GPIO_2_21);
+
+	/* EIM_D17 - GPIO3[17] for VCOM control */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D17__GPIO_3_17);
+
+	/* Set as output */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_GDIR);
+	reg |= (1 << 17);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_GDIR);
+
+	/* EIM_D20 - GPIO3[20] for EPD PMIC WAKEUP */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D20__GPIO_3_20);
+	/* Set as output */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_GDIR);
+	reg |= (1 << 20);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_GDIR);
+
+	/* EIM_A18 - GPIO2[20] for EPD PWR CTL0 */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A18__GPIO_2_20);
+	/* Set as output */
+	reg = readl(GPIO2_BASE_ADDR + GPIO_GDIR);
+	reg |= (1 << 20);
+	writel(reg, GPIO2_BASE_ADDR + GPIO_GDIR);
+}
+
+void epdc_power_on()
+{
+	unsigned int reg;
+
+	/* Set EPD_PWR_CTL0 to high - enable EINK_VDD (3.15) */
+	reg = readl(GPIO2_BASE_ADDR + GPIO_DR);
+	reg |= (1 << 20);
+	writel(reg, GPIO2_BASE_ADDR + GPIO_DR);
+
+	/* Set PMIC Wakeup to high - enable Display power */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+	reg |= (1 << 20);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+
+	/* Wait for PWRGOOD == 1 */
+	while (1) {
+		reg = readl(GPIO2_BASE_ADDR + GPIO_DR);
+		if (!(reg & (1 << 21)))
+			break;
+
+		udelay(100);
+	}
+
+	/* Enable VCOM */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+	reg |= (1 << 17);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+
+	reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+
+	udelay(500);
+}
+
+void  epdc_power_off()
+{
+	unsigned int reg;
+	/* Set PMIC Wakeup to low - disable Display power */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+	reg &= ~(1 << 20);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+
+	/* Disable VCOM */
+	reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+	reg &= ~(1 << 17);
+	writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+
+	/* Set EPD_PWR_CTL0 to low - disable EINK_VDD (3.15) */
+	reg = readl(GPIO2_BASE_ADDR + GPIO_DR);
+	reg &= ~(1 << 20);
+	writel(reg, GPIO2_BASE_ADDR + GPIO_DR);
+}
+
+int setup_waveform_file()
+{
+#ifdef CONFIG_WAVEFORM_FILE_IN_MMC
+	int mmc_dev = get_mmc_env_devno();
+	ulong offset = CONFIG_WAVEFORM_FILE_OFFSET;
+	ulong size = CONFIG_WAVEFORM_FILE_SIZE;
+	ulong addr = CONFIG_WAVEFORM_BUF_ADDR;
+	char *s = NULL;
+	struct mmc *mmc = find_mmc_device(mmc_dev);
+	uint blk_start, blk_cnt, n;
+
+	if (!mmc) {
+		printf("MMC Device %d not found\n",
+			mmc_dev);
+		return -1;
+	}
+
+	if (mmc_init(mmc)) {
+		puts("MMC init failed\n");
+		return -1;
+	}
+
+	blk_start = ALIGN(offset, mmc->read_bl_len) / mmc->read_bl_len;
+	blk_cnt   = ALIGN(size, mmc->read_bl_len) / mmc->read_bl_len;
+	n = mmc->block_dev.block_read(mmc_dev, blk_start,
+		blk_cnt, (u_char *)addr);
+	flush_cache((ulong)addr, blk_cnt * mmc->read_bl_len);
+
+	return (n == blk_cnt) ? 0 : -1;
+#else
+	return -1;
+#endif
+}
+
+static void setup_epdc()
+{
+	unsigned int reg;
+
+	/* epdc iomux settings */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A16__EPDC_SDDO_0);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA10__EPDC_SDDO_1);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA12__EPDC_SDDO_2);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA11__EPDC_SDDO_3);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_LBA__EPDC_SDDO_4);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_EB2__EPDC_SDDO_5);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_CS0__EPDC_SDDO_6);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_RW__EPDC_SDDO_7);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A21__EPDC_GDCLK);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A22__EPDC_GDSP);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A23__EPDC_GDOE);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A24__EPDC_GDRL);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D31__EPDC_SDCLK);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D27__EPDC_SDOE);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA1__EPDC_SDLE);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_EB1__EPDC_SDSHR);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA2__EPDC_BDR_0);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA4__EPDC_SDCE_0);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA5__EPDC_SDCE_1);
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA6__EPDC_SDCE_2);
+
+	/*** epdc Maxim PMIC settings ***/
+
+	/* EPDC PWRSTAT - GPIO2[21] for PWR_GOOD status */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A17__GPIO_2_21);
+
+	/* EPDC VCOM0 - GPIO3[17] for VCOM control */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D17__GPIO_3_17);
+
+	/* UART4 TXD - GPIO3[20] for EPD PMIC WAKEUP */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D20__GPIO_3_20);
+
+	/* EIM_A18 - GPIO2[20] for EPD PWR CTL0 */
+	mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A18__GPIO_2_20);
+
+	/*** Set pixel clock rates for EPDC ***/
+
+	/* EPDC AXI clk (IPU2_CLK) from PFD_400M, set to 396/2 = 198MHz */
+	reg = readl(CCM_BASE_ADDR + CLKCTL_CSCDR3);
+	reg &= ~0x7C000;
+	reg |= (1 << 16) | (1 << 14);
+	writel(reg, CCM_BASE_ADDR + CLKCTL_CSCDR3);
+
+	/* EPDC AXI clk enable */
+	reg = readl(CCM_BASE_ADDR + CLKCTL_CCGR3);
+	reg |= 0x00C0;
+	writel(reg, CCM_BASE_ADDR + CLKCTL_CCGR3);
+
+	/* EPDC PIX clk (IPU2_DI1_CLK) from PLL5, set to 650/4/6 = ~27MHz */
+	reg = readl(CCM_BASE_ADDR + CLKCTL_CSCDR2);
+	reg &= ~0x3FE00;
+	reg |= (2 << 15) | (5 << 12);
+	writel(reg, CCM_BASE_ADDR + CLKCTL_CSCDR2);
+
+	/* PLL5 enable (defaults to 650) */
+	reg = readl(ANATOP_BASE_ADDR + ANATOP_PLL_VIDEO);
+	reg &= ~((1 << 16) | (1 << 12));
+	reg |= (1 << 13);
+	writel(reg, ANATOP_BASE_ADDR + ANATOP_PLL_VIDEO);
+
+	/* EPDC PIX clk enable */
+	reg = readl(CCM_BASE_ADDR + CLKCTL_CCGR3);
+	reg |= 0x0C00;
+	writel(reg, CCM_BASE_ADDR + CLKCTL_CCGR3);
+
+	panel_info.epdc_data.working_buf_addr = CONFIG_WORKING_BUF_ADDR;
+	panel_info.epdc_data.waveform_buf_addr = CONFIG_WAVEFORM_BUF_ADDR;
+
+	panel_info.epdc_data.wv_modes.mode_init = 0;
+	panel_info.epdc_data.wv_modes.mode_du = 1;
+	panel_info.epdc_data.wv_modes.mode_gc4 = 3;
+	panel_info.epdc_data.wv_modes.mode_gc8 = 2;
+	panel_info.epdc_data.wv_modes.mode_gc16 = 2;
+	panel_info.epdc_data.wv_modes.mode_gc32 = 2;
+
+	panel_info.epdc_data.epdc_timings = panel_timings;
+
+	setup_epdc_power();
+
+	/* Assign fb_base */
+	gd->fb_base = CONFIG_FB_BASE;
+}
+#endif
+
 /* For DDR mode operation, provide target delay parameter for each SD port.
  * Use cfg->esdhc_base to distinguish the SD port #. The delay for each port
  * is dependent on signal layout for that particular port.  If the following
@@ -1039,6 +1325,7 @@ u32 get_ddr_delay(struct fsl_esdhc_cfg *cfg)
 
 #endif
 
+#ifndef CONFIG_MXC_EPDC
 #ifdef CONFIG_LCD
 void lcd_enable(void)
 {
@@ -1140,6 +1427,7 @@ void setup_splash_image(void)
 	}
 }
 #endif
+#endif /* !CONFIG_MXC_EPDC */
 
 int board_init(void)
 {
@@ -1185,6 +1473,10 @@ int board_init(void)
 #ifdef CONFIG_NAND_GPMI
 	setup_gpmi_nand();
 #endif
+
+#ifdef CONFIG_MXC_EPDC
+	setup_epdc();
+#endif
 	return 0;
 }
 
diff --git a/include/asm-arm/arch-mx6/mx6.h b/include/asm-arm/arch-mx6/mx6.h
index 26dd0b3..d03adc9 100644
--- a/include/asm-arm/arch-mx6/mx6.h
+++ b/include/asm-arm/arch-mx6/mx6.h
@@ -266,15 +266,15 @@
 #define CSI_BASE_ADDR               (AIPS1_OFF_BASE_ADDR + 0x64000)
 #define SIPIX_BASE_ADDR             (AIPS1_OFF_BASE_ADDR + 0x68000)
 #define SDMA_PORT_HOST_BASE_ADDR    (AIPS1_OFF_BASE_ADDR + 0x6C000)
-#define EPXP_BASE_ADDR              (AIPS1_OFF_BASE_ADDR + 0x70000)
-#define EPDC_BASE_ADDR              (AIPS1_OFF_BASE_ADDR + 0x74000)
-#define ELCDIF_BASE_ADDR            (AIPS1_OFF_BASE_ADDR + 0x78000)
-#define DCP_BASE_ADDR               (AIPS1_OFF_BASE_ADDR + 0x7C000)
 #else
 #define DCIC1_BASE_ADDR             (AIPS1_OFF_BASE_ADDR + 0x64000)
 #define DCIC2_BASE_ADDR             (AIPS1_OFF_BASE_ADDR + 0x68000)
 #define DMA_REQ_PORT_HOST_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x6C000)
 #endif
+#define EPXP_BASE_ADDR              (AIPS1_OFF_BASE_ADDR + 0x70000)
+#define EPDC_BASE_ADDR              (AIPS1_OFF_BASE_ADDR + 0x74000)
+#define ELCDIF_BASE_ADDR            (AIPS1_OFF_BASE_ADDR + 0x78000)
+#define DCP_BASE_ADDR               (AIPS1_OFF_BASE_ADDR + 0x7C000)
 
 /* ATZ#2- On Platform */
 #define AIPS2_ON_BASE_ADDR          (ATZ2_BASE_ADDR + 0x7C000)
@@ -697,8 +697,9 @@
 #define CLKCTL_CCGR7            0x84
 #define CLKCTL_CMEOR            0x88
 
-#define ANATOP_USB1				0x10
-#define ANATOP_USB2				0x20
+#define ANATOP_USB1		0x10
+#define ANATOP_USB2		0x20
+#define ANATOP_PLL_VIDEO	0xA0
 
 #define CHIP_TYPE_DQ		0x63000
 #define CHIP_TYPE_DL		0x61000
diff --git a/include/configs/mx6dl_arm2.h b/include/configs/mx6dl_arm2.h
index 8b1d50c..72fd980 100644
--- a/include/configs/mx6dl_arm2.h
+++ b/include/configs/mx6dl_arm2.h
@@ -299,22 +299,48 @@
 	#define CONFIG_ENV_IS_NOWHERE	1
 #endif
 
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_MXC_EPDC
+
+/*
+ * SPLASH SCREEN Configs
+ */
 #ifdef CONFIG_SPLASH_SCREEN
 	/*
 	 * Framebuffer and LCD
 	 */
 	#define CONFIG_LCD
+	#define CONFIG_FB_BASE				(TEXT_BASE + 0x300000)
+	#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#ifdef CONFIG_MXC_EPDC
+	#undef LCD_TEST_PATTERN
+	/* #define CONFIG_SPLASH_IS_IN_MMC			1 */
+	#define LCD_BPP					LCD_MONOCHROME
+	/* #define CONFIG_SPLASH_SCREEN_ALIGN		1 */
+
+	#define CONFIG_MXC_EPDC				1
+
+	#define CONFIG_WORKING_BUF_ADDR			(TEXT_BASE + 0x100000)
+	#define CONFIG_WAVEFORM_BUF_ADDR		(TEXT_BASE + 0x200000)
+	#define CONFIG_WAVEFORM_FILE_OFFSET		0x100000
+	#define CONFIG_WAVEFORM_FILE_SIZE		0xF0988
+	#define CONFIG_WAVEFORM_FILE_IN_MMC
+
+#ifdef CONFIG_SPLASH_IS_IN_MMC
+	#define CONFIG_SPLASH_IMG_OFFSET		0x4c000
+	#define CONFIG_SPLASH_IMG_SIZE			0x19000
+#endif
+#else /* !CONFIG_MXC_EPDC */
 	#define CONFIG_IPU_V3H
 	#define CONFIG_VIDEO_MX5
 	#define CONFIG_IPU_CLKRATE	260000000
 	#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
 	#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
-	#define CONFIG_SYS_CONSOLE_IS_IN_ENV
 	#define LCD_BPP		LCD_COLOR16
 	#define CONFIG_CMD_BMP
 	#define CONFIG_BMP_8BPP
-	#define CONFIG_FB_BASE	(TEXT_BASE + 0x300000)
 	#define CONFIG_SPLASH_SCREEN_ALIGN
 	#define CONFIG_SYS_WHITE_ON_BLACK
 #endif
+#endif /* CONFIG_SPLASH_SCREEN */
 #endif				/* __CONFIG_H */
diff --git a/include/configs/mx6dl_sabresd.h b/include/configs/mx6dl_sabresd.h
index 5a9bde3..060c94a 100644
--- a/include/configs/mx6dl_sabresd.h
+++ b/include/configs/mx6dl_sabresd.h
@@ -303,22 +303,48 @@
 	#define CONFIG_ENV_IS_NOWHERE	1
 #endif
 
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_MXC_EPDC
+
+/*
+ * SPLASH SCREEN Configs
+ */
 #ifdef CONFIG_SPLASH_SCREEN
 	/*
 	 * Framebuffer and LCD
 	 */
 	#define CONFIG_LCD
+	#define CONFIG_FB_BASE				(TEXT_BASE + 0x300000)
+	#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#ifdef CONFIG_MXC_EPDC
+	#undef LCD_TEST_PATTERN
+	/* #define CONFIG_SPLASH_IS_IN_MMC			1 */
+	#define LCD_BPP					LCD_MONOCHROME
+	/* #define CONFIG_SPLASH_SCREEN_ALIGN		1 */
+
+	#define CONFIG_MXC_EPDC				1
+
+	#define CONFIG_WORKING_BUF_ADDR			(TEXT_BASE + 0x100000)
+	#define CONFIG_WAVEFORM_BUF_ADDR		(TEXT_BASE + 0x200000)
+	#define CONFIG_WAVEFORM_FILE_OFFSET		0x100000
+	#define CONFIG_WAVEFORM_FILE_SIZE		0xF0988
+	#define CONFIG_WAVEFORM_FILE_IN_MMC
+
+#ifdef CONFIG_SPLASH_IS_IN_MMC
+	#define CONFIG_SPLASH_IMG_OFFSET		0x4c000
+	#define CONFIG_SPLASH_IMG_SIZE			0x19000
+#endif
+#else /* !CONFIG_MXC_EPDC */
 	#define CONFIG_IPU_V3H
 	#define CONFIG_VIDEO_MX5
 	#define CONFIG_IPU_CLKRATE	260000000
 	#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
 	#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
-	#define CONFIG_SYS_CONSOLE_IS_IN_ENV
 	#define LCD_BPP		LCD_COLOR16
 	#define CONFIG_CMD_BMP
 	#define CONFIG_BMP_8BPP
-	#define CONFIG_FB_BASE	(TEXT_BASE + 0x300000)
 	#define CONFIG_SPLASH_SCREEN_ALIGN
 	#define CONFIG_SYS_WHITE_ON_BLACK
 #endif
+#endif /* CONFIG_SPLASH_SCREEN */
 #endif				/* __CONFIG_H */