Merge branch 'master' of git://git.denx.de/u-boot-arm

30 files changed, 842 insertions, 266 deletions

diff --git a/board/davinci/common/psc.c b/board/davinci/common/psc.c
index d538d51..28e2a4b 100644
--- a/board/davinci/common/psc.c
+++ b/board/davinci/common/psc.c
@@ -26,6 +26,14 @@
 #include <common.h>
 #include <asm/arch/hardware.h>
 
+#define PINMUX0_EMACEN (1 << 31)
+#define PINMUX0_AECS5  (1 << 11)
+#define PINMUX0_AECS4  (1 << 10)
+
+#define PINMUX1_I2C    (1 <<  7)
+#define PINMUX1_UART1  (1 <<  1)
+#define PINMUX1_UART0  (1 <<  0)
+
 /*
  * The DM6446 includes two separate power domains: "Always On" and "DSP". The
  * "Always On" power domain is always on when the chip is on. The "Always On"
@@ -115,3 +123,60 @@ void dsp_on(void)
 	REG(PSC_GBLCTL) &= ~0x1f;
 }
 #endif /* CONFIG_SYS_USE_DSPLINK */
+
+void davinci_enable_uart0(void)
+{
+	lpsc_on(DAVINCI_LPSC_UART0);
+
+	/* Bringup UART0 out of reset */
+	REG(UART0_PWREMU_MGMT) = 0x0000e003;
+
+	/* Enable UART0 MUX lines */
+	REG(PINMUX1) |= PINMUX1_UART0;
+}
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+void davinci_enable_emac(void)
+{
+	lpsc_on(DAVINCI_LPSC_EMAC);
+	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
+	lpsc_on(DAVINCI_LPSC_MDIO);
+
+	/* Enable GIO3.3V cells used for EMAC */
+	REG(VDD3P3V_PWDN) = 0;
+
+	/* Enable EMAC. */
+	REG(PINMUX0) |= PINMUX0_EMACEN;
+}
+#endif
+
+void davinci_enable_i2c(void)
+{
+	lpsc_on(DAVINCI_LPSC_I2C);
+
+	/* Enable I2C pin Mux */
+	REG(PINMUX1) |= PINMUX1_I2C;
+}
+
+void davinci_errata_workarounds(void)
+{
+	/*
+	 * Workaround for TMS320DM6446 errata 1.3.22:
+	 *   PSC: PTSTAT Register Does Not Clear After Warm/Maximum Reset
+	 *   Revision(s) Affected: 1.3 and earlier
+	 */
+	REG(PSC_SILVER_BULLET) = 0;
+
+	/*
+	 * Set the PR_OLD_COUNT bits in the Bus Burst Priority Register (PBBPR)
+	 * as suggested in TMS320DM6446 errata 2.1.2:
+	 *
+	 * On DM6446 Silicon Revision 2.1 and earlier, under certain conditions
+	 * low priority modules can occupy the bus and prevent high priority
+	 * modules like the VPSS from getting the required DDR2 throughput.
+	 * A hex value of 0x20 should provide a good ARM (cache enabled)
+	 * performance and still allow good utilization by the VPSS or other
+	 * modules.
+	 */
+	REG(VBPR) = 0x20;
+}
diff --git a/board/davinci/common/psc.h b/board/davinci/common/psc.h
index 6ab2575..b2dd7b5 100644
--- a/board/davinci/common/psc.h
+++ b/board/davinci/common/psc.h
@@ -24,5 +24,9 @@
 
 void lpsc_on(unsigned int id);
 void dsp_on(void);
+void davinci_enable_uart0(void);
+void davinci_enable_emac(void);
+void davinci_enable_i2c(void);
+void davinci_errata_workarounds(void);
 
 #endif /* __PSC_H */
diff --git a/board/davinci/dvevm/dvevm.c b/board/davinci/dvevm/dvevm.c
index 3fe8858..22308de 100644
--- a/board/davinci/dvevm/dvevm.c
+++ b/board/davinci/dvevm/dvevm.c
@@ -27,7 +27,6 @@
 #include <common.h>
 #include <i2c.h>
 #include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
 #include "../common/psc.h"
 #include "../common/misc.h"
 
@@ -41,16 +40,13 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
 
-	/* Workaround for TMS320DM6446 errata 1.3.22 */
-	REG(PSC_SILVER_BULLET) = 0;
+	/* Configure AEMIF pins (although this should be configured at boot time
+	 * with pull-up/pull-down resistors) */
+	REG(PINMUX0) = 0x00000c1f;
+
+	davinci_errata_workarounds();
 
 	/* Power on required peripherals */
-	lpsc_on(DAVINCI_LPSC_EMAC);
-	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
-	lpsc_on(DAVINCI_LPSC_MDIO);
-	lpsc_on(DAVINCI_LPSC_I2C);
-	lpsc_on(DAVINCI_LPSC_UART0);
-	lpsc_on(DAVINCI_LPSC_TIMER1);
 	lpsc_on(DAVINCI_LPSC_GPIO);
 	lpsc_on(DAVINCI_LPSC_USB);
 
@@ -59,24 +55,11 @@ int board_init(void)
 	dsp_on();
 #endif /* CONFIG_SYS_USE_DSPLINK */
 
-	/* Bringup UART0 out of reset */
-	REG(UART0_PWREMU_MGMT) = 0x0000e003;
-
-	/* Enable GIO3.3V cells used for EMAC */
-	REG(VDD3P3V_PWDN) = 0;
-
-	/* Enable UART0 MUX lines */
-	REG(PINMUX1) |= 1;
-
-	/* Enable EMAC and AEMIF pins */
-	REG(PINMUX0) = 0x80000c1f;
-
-	/* Enable I2C pin Mux */
-	REG(PINMUX1) |= (1 << 7);
-
-	/* Set the Bus Priority Register to appropriate value */
-	REG(VBPR) = 0x20;
+	davinci_enable_uart0();
+	davinci_enable_emac();
+	davinci_enable_i2c();
 
+	lpsc_on(DAVINCI_LPSC_TIMER1);
 	timer_init();
 
 	return(0);
diff --git a/board/davinci/schmoogie/schmoogie.c b/board/davinci/schmoogie/schmoogie.c
index 3504a2e..433769a 100644
--- a/board/davinci/schmoogie/schmoogie.c
+++ b/board/davinci/schmoogie/schmoogie.c
@@ -27,7 +27,6 @@
 #include <common.h>
 #include <i2c.h>
 #include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
 #include "../common/psc.h"
 #include "../common/misc.h"
 
@@ -41,16 +40,13 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
 
-	/* Workaround for TMS320DM6446 errata 1.3.22 */
-	REG(PSC_SILVER_BULLET) = 0;
+	/* Configure AEMIF pins (although this should be configured at boot time
+	 * with pull-up/pull-down resistors) */
+	REG(PINMUX0) = 0x00000c1f;
+
+	davinci_errata_workarounds();
 
 	/* Power on required peripherals */
-	lpsc_on(DAVINCI_LPSC_EMAC);
-	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
-	lpsc_on(DAVINCI_LPSC_MDIO);
-	lpsc_on(DAVINCI_LPSC_I2C);
-	lpsc_on(DAVINCI_LPSC_UART0);
-	lpsc_on(DAVINCI_LPSC_TIMER1);
 	lpsc_on(DAVINCI_LPSC_GPIO);
 
 #if !defined(CONFIG_SYS_USE_DSPLINK)
@@ -58,24 +54,11 @@ int board_init(void)
 	dsp_on();
 #endif /* CONFIG_SYS_USE_DSPLINK */
 
-	/* Bringup UART0 out of reset */
-	REG(UART0_PWREMU_MGMT) = 0x0000e003;
-
-	/* Enable GIO3.3V cells used for EMAC */
-	REG(VDD3P3V_PWDN) = 0;
-
-	/* Enable UART0 MUX lines */
-	REG(PINMUX1) |= 1;
-
-	/* Enable EMAC and AEMIF pins */
-	REG(PINMUX0) = 0x80000c1f;
-
-	/* Enable I2C pin Mux */
-	REG(PINMUX1) |= (1 << 7);
-
-	/* Set the Bus Priority Register to appropriate value */
-	REG(VBPR) = 0x20;
+	davinci_enable_uart0();
+	davinci_enable_emac();
+	davinci_enable_i2c();
 
+	lpsc_on(DAVINCI_LPSC_TIMER1);
 	timer_init();
 
 	return(0);
@@ -87,7 +70,7 @@ int misc_init_r(void)
 	int		i = 0;
 
 	/* Set serial number from UID chip */
-	u_int8_t	crc_tbl[256] = {
+	const u_int8_t	crc_tbl[256] = {
 			0x00, 0x5e, 0xbc, 0xe2, 0x61, 0x3f, 0xdd, 0x83,
 			0xc2, 0x9c, 0x7e, 0x20, 0xa3, 0xfd, 0x1f, 0x41,
 			0x9d, 0xc3, 0x21, 0x7f, 0xfc, 0xa2, 0x40, 0x1e,
diff --git a/board/davinci/sffsdr/sffsdr.c b/board/davinci/sffsdr/sffsdr.c
index 9296d7b..e76f86d 100644
--- a/board/davinci/sffsdr/sffsdr.c
+++ b/board/davinci/sffsdr/sffsdr.c
@@ -30,7 +30,6 @@
 #include <common.h>
 #include <i2c.h>
 #include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
 #include "../common/psc.h"
 #include "../common/misc.h"
 
@@ -51,16 +50,9 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
 
-	/* Workaround for TMS320DM6446 errata 1.3.22 */
-	REG(PSC_SILVER_BULLET) = 0;
+	davinci_errata_workarounds();
 
 	/* Power on required peripherals */
-	lpsc_on(DAVINCI_LPSC_EMAC);
-	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
-	lpsc_on(DAVINCI_LPSC_MDIO);
-	lpsc_on(DAVINCI_LPSC_I2C);
-	lpsc_on(DAVINCI_LPSC_UART0);
-	lpsc_on(DAVINCI_LPSC_TIMER1);
 	lpsc_on(DAVINCI_LPSC_GPIO);
 
 #if !defined(CONFIG_SYS_USE_DSPLINK)
@@ -68,24 +60,11 @@ int board_init(void)
 	dsp_on();
 #endif /* CONFIG_SYS_USE_DSPLINK */
 
-	/* Bringup UART0 out of reset */
-	REG(UART0_PWREMU_MGMT) = 0x0000e003;
-
-	/* Enable GIO3.3V cells used for EMAC */
-	REG(VDD3P3V_PWDN) = 0;
-
-	/* Enable UART0 MUX lines */
-	REG(PINMUX1) |= 1;
-
-	/* Enable EMAC and AEMIF pins */
-	REG(PINMUX0) = 0x80000c1f;
-
-	/* Enable I2C pin Mux */
-	REG(PINMUX1) |= (1 << 7);
-
-	/* Set the Bus Priority Register to appropriate value */
-	REG(VBPR) = 0x20;
+	davinci_enable_uart0();
+	davinci_enable_emac();
+	davinci_enable_i2c();
 
+	lpsc_on(DAVINCI_LPSC_TIMER1);
 	timer_init();
 
 	return(0);
diff --git a/board/davinci/sonata/sonata.c b/board/davinci/sonata/sonata.c
index 6de9356..d56b443 100644
--- a/board/davinci/sonata/sonata.c
+++ b/board/davinci/sonata/sonata.c
@@ -26,7 +26,6 @@
 
 #include <common.h>
 #include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
 #include "../common/psc.h"
 #include "../common/misc.h"
 
@@ -40,16 +39,13 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
 
-	/* Workaround for TMS320DM6446 errata 1.3.22 */
-	REG(PSC_SILVER_BULLET) = 0;
+	/* Configure AEMIF pins (although this should be configured at boot time
+	 * with pull-up/pull-down resistors) */
+	REG(PINMUX0) = 0x00000c1f;
+
+	davinci_errata_workarounds();
 
 	/* Power on required peripherals */
-	lpsc_on(DAVINCI_LPSC_EMAC);
-	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
-	lpsc_on(DAVINCI_LPSC_MDIO);
-	lpsc_on(DAVINCI_LPSC_I2C);
-	lpsc_on(DAVINCI_LPSC_UART0);
-	lpsc_on(DAVINCI_LPSC_TIMER1);
 	lpsc_on(DAVINCI_LPSC_GPIO);
 
 #if !defined(CONFIG_SYS_USE_DSPLINK)
@@ -57,24 +53,11 @@ int board_init(void)
 	dsp_on();
 #endif /* CONFIG_SYS_USE_DSPLINK */
 
-	/* Bringup UART0 out of reset */
-	REG(UART0_PWREMU_MGMT) = 0x0000e003;
-
-	/* Enable GIO3.3V cells used for EMAC */
-	REG(VDD3P3V_PWDN) = 0;
-
-	/* Enable UART0 MUX lines */
-	REG(PINMUX1) |= 1;
-
-	/* Enable EMAC and AEMIF pins */
-	REG(PINMUX0) = 0x80000c1f;
-
-	/* Enable I2C pin Mux */
-	REG(PINMUX1) |= (1 << 7);
-
-	/* Set the Bus Priority Register to appropriate value */
-	REG(VBPR) = 0x20;
+	davinci_enable_uart0();
+	davinci_enable_emac();
+	davinci_enable_i2c();
 
+	lpsc_on(DAVINCI_LPSC_TIMER1);
 	timer_init();
 
 	return(0);
diff --git a/board/omap3/beagle/beagle.c b/board/omap3/beagle/beagle.c
index ecdea09..7377058 100644
--- a/board/omap3/beagle/beagle.c
+++ b/board/omap3/beagle/beagle.c
@@ -36,6 +36,8 @@
 #include <asm/mach-types.h>
 #include "beagle.h"
 
+static int beagle_revision_c;
+
 /******************************************************************************
  * Routine: board_init
  * Description: Early hardware init.
@@ -54,6 +56,43 @@ int board_init(void)
 }
 
 /******************************************************************************
+ * Routine: beagle_get_revision
+ * Description: Return revision of the BeagleBoard this code is running on.
+ *              If it is a revision Ax/Bx board, this function returns 0,
+ *              on a revision C board you will get a 1.
+ *****************************************************************************/
+int beagle_get_revision(void)
+{
+	return beagle_revision_c;
+}
+
+/******************************************************************************
+ * Routine: beagle_identify
+ * Description: Detect if we are running on a Beagle revision Ax/Bx or
+ *              Cx. This can be done by GPIO_171. If this is low, we are
+ *              running on a revision C board.
+ *****************************************************************************/
+void beagle_identify(void)
+{
+	gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
+
+	/* Configure GPIO 171 as input */
+	writel(readl(&gpio6_base->oe) | GPIO11, &gpio6_base->oe);
+
+	/* Get value of GPIO 171 */
+	beagle_revision_c = readl(&gpio6_base->datain) & BOARD_REVISION_MASK;
+
+	printf("Board revision ");
+	if (beagle_revision_c) {
+		printf("Ax/Bx\n");
+		beagle_revision_c = 0;
+	} else {
+		printf("C\n");
+		beagle_revision_c = 1;
+	}
+}
+
+/******************************************************************************
  * Routine: misc_init_r
  * Description: Configure board specific parts
  *****************************************************************************/
@@ -75,6 +114,8 @@ int misc_init_r(void)
 	writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
 		GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
 
+	beagle_identify();
+
 	return 0;
 }
 
diff --git a/board/omap3/beagle/beagle.h b/board/omap3/beagle/beagle.h
index 6511ffa..d66f159 100644
--- a/board/omap3/beagle/beagle.h
+++ b/board/omap3/beagle/beagle.h
@@ -27,7 +27,6 @@ const omap3_sysinfo sysinfo = {
 	SDP_3430_V1,
 	SDP_3430_V2,
 	DDR_STACKED,
-	"3530",
 	"OMAP3 Beagle board",
 #if defined(CONFIG_ENV_IS_IN_ONENAND)
 	"OneNAND",
@@ -36,6 +35,8 @@ const omap3_sysinfo sysinfo = {
 #endif
 };
 
+#define BOARD_REVISION_MASK	(0x1 << 11)
+
 /*
  * IEN  - Input Enable
  * IDIS - Input Disable
diff --git a/board/omap3/evm/evm.h b/board/omap3/evm/evm.h
index 4ecea7f..199824f 100644
--- a/board/omap3/evm/evm.h
+++ b/board/omap3/evm/evm.h
@@ -27,7 +27,6 @@ const omap3_sysinfo sysinfo = {
 	OMAP3EVM_V1,
 	OMAP3EVM_V2,
 	DDR_DISCRETE,
-	"35X-Family",
 	"OMAP3 EVM board",
 #if defined(CONFIG_ENV_IS_IN_ONENAND)
 	"OneNAND",
diff --git a/board/omap3/overo/Makefile b/board/omap3/overo/Makefile
index c165629..dd673ca 100644
--- a/board/omap3/overo/Makefile
+++ b/board/omap3/overo/Makefile
@@ -44,4 +44,5 @@ distclean:	clean
 # defines $(obj).depend target
 include $(SRCTREE)/rules.mk
 
+#########################################################################
 sinclude $(obj).depend
diff --git a/board/omap3/overo/overo.c b/board/omap3/overo/overo.c
index 7964123..48375ad 100644
--- a/board/omap3/overo/overo.c
+++ b/board/omap3/overo/overo.c
@@ -58,21 +58,8 @@ int board_init(void)
  *****************************************************************************/
 int misc_init_r(void)
 {
-	gpio_t *gpio5_base = (gpio_t *)OMAP34XX_GPIO5_BASE;
-	gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
-
 	power_init_r();
 
-	/* Configure GPIOs to output */
-	writel(~((GPIO10) | GPIO9 | GPIO3 | GPIO2), &gpio6_base->oe);
-	writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
-		GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
-
-	/* Set GPIOs */
-	writel(GPIO10 | GPIO9 | GPIO3 | GPIO2, &gpio6_base->setdataout);
-	writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
-		GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
-
 	return 0;
 }
 
diff --git a/board/omap3/overo/overo.h b/board/omap3/overo/overo.h
index 3c1b6bc..71de3f1 100644
--- a/board/omap3/overo/overo.h
+++ b/board/omap3/overo/overo.h
@@ -27,7 +27,6 @@ const omap3_sysinfo sysinfo = {
 	SDP_3430_V1,
 	SDP_3430_V2,
 	DDR_STACKED,
-	"3503",
 	"Gumstix Overo board",
 #if defined(CONFIG_ENV_IS_IN_ONENAND)
 	"OneNAND",
@@ -130,7 +129,8 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(GPMC_NWP),		(IEN  | PTD | DIS | M0)) /*GPMC_nWP*/\
  MUX_VAL(CP(GPMC_WAIT0),	(IEN  | PTU | EN  | M0)) /*GPMC_WAIT0*/\
  MUX_VAL(CP(GPMC_WAIT1),	(IEN  | PTU | EN  | M0)) /*GPMC_WAIT1*/\
- MUX_VAL(CP(GPMC_WAIT2),	(IEN  | PTU | EN  | M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_WAIT2),	(IEN  | PTU | DIS | M4)) /*GPIO_64*/\
+							/* - SMSC911X_NRES*/\
  MUX_VAL(CP(GPMC_WAIT3),	(IEN  | PTU | EN  | M0)) /*GPMC_nCS3*/\
  /*DSS*/\
  MUX_VAL(CP(DSS_PCLK),		(IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
@@ -184,7 +184,7 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(CAM_STROBE),	(IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
  MUX_VAL(CP(CSI2_DX0),		(IEN  | PTD | DIS | M0)) /*CSI2_DX0*/\
  MUX_VAL(CP(CSI2_DY0),		(IEN  | PTD | DIS | M0)) /*CSI2_DY0*/\
- MUX_VAL(CP(CSI2_DX1),		(IEN  | PTD | DIS | M0)) /*CSI2_DX1*/\
+ MUX_VAL(CP(CSI2_DX1),		(IEN  | PTD | EN  | M4)) /*GPIO_114*/\
  MUX_VAL(CP(CSI2_DY1),		(IEN  | PTU | EN  | M4)) /*GPIO_115*/\
  /*Audio Interface */\
  MUX_VAL(CP(MCBSP2_FSX),	(IEN  | PTD | DIS | M0)) /*McBSP2_FSX*/\
@@ -218,10 +218,10 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(MCBSP3_DR),		(IDIS | PTD | DIS | M1)) /*UART2_RTS*/\
  MUX_VAL(CP(MCBSP3_CLKX),	(IDIS | PTD | DIS | M1)) /*UART2_TX*/\
  MUX_VAL(CP(MCBSP3_FSX),	(IEN  | PTD | DIS | M1)) /*UART2_RX*/\
- MUX_VAL(CP(UART2_CTS),		(IDIS | PTD | DIS | M4)) /*GPIO_144 - LCD_EN*/\
- MUX_VAL(CP(UART2_RTS),		(IDIS | PTD | DIS | M4)) /*GPIO_145*/\
- MUX_VAL(CP(UART2_TX),		(IDIS | PTD | DIS | M4)) /*GPIO_146*/\
- MUX_VAL(CP(UART2_RX),		(IDIS | PTD | DIS | M4)) /*GPIO_147*/\
+ MUX_VAL(CP(UART2_CTS),		(IEN  | PTD | DIS | M4)) /*GPIO_144 - LCD_EN*/\
+ MUX_VAL(CP(UART2_RTS),		(IEN  | PTD | DIS | M4)) /*GPIO_145*/\
+ MUX_VAL(CP(UART2_TX),		(IEN  | PTD | DIS | M4)) /*GPIO_146*/\
+ MUX_VAL(CP(UART2_RX),		(IEN  | PTD | DIS | M4)) /*GPIO_147*/\
  MUX_VAL(CP(UART1_TX),		(IDIS | PTD | DIS | M0)) /*UART1_TX*/\
  MUX_VAL(CP(UART1_RTS),		(IEN  | PTU | DIS | M4)) /*GPIO_149*/ \
  MUX_VAL(CP(UART1_CTS),		(IEN  | PTU | DIS | M4)) /*GPIO_150-MMC3_WP*/\
@@ -271,7 +271,8 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(MCSPI1_SOMI),	(IEN  | PTD | DIS | M0)) /*McSPI1_SOMI */\
  MUX_VAL(CP(MCSPI1_CS0),	(IEN  | PTD | EN  | M0)) /*McSPI1_CS0*/\
  MUX_VAL(CP(MCSPI1_CS1),	(IDIS | PTD | EN  | M0)) /*McSPI1_CS1*/\
- MUX_VAL(CP(MCSPI1_CS2),	(IDIS | PTD | DIS | M4)) /*GPIO_176*/\
+ MUX_VAL(CP(MCSPI1_CS2),	(IEN  | PTD | DIS | M4)) /*GPIO_176*/\
+							/* - SMSC911X_IRQ*/\
  MUX_VAL(CP(MCSPI1_CS3),	(IEN  | PTD | DIS | M3)) /*HSUSB2_DATA2*/\
  MUX_VAL(CP(MCSPI2_CLK),	(IEN  | PTD | DIS | M3)) /*HSUSB2_DATA7*/\
  MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | DIS | M3)) /*HSUSB2_DATA4*/\
@@ -306,7 +307,7 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(ETK_D8_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT6*/\
  MUX_VAL(CP(ETK_D9_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT5*/\
  MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_CLK*/\
- MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTU | EN  | M3)) /*HSUSB2_STP*/\
+ MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_STP*/\
  MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | DIS | M3)) /*HSUSB2_DIR*/\
  MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | DIS | M3)) /*HSUSB2_NXT*/\
  MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | DIS | M3)) /*HSUSB2_DATA0*/\
diff --git a/board/omap3/pandora/pandora.h b/board/omap3/pandora/pandora.h
index 8525a03..dd09f12 100644
--- a/board/omap3/pandora/pandora.h
+++ b/board/omap3/pandora/pandora.h
@@ -27,7 +27,6 @@ const omap3_sysinfo sysinfo = {
 	SDP_3430_V1,
 	SDP_3430_V2,
 	DDR_STACKED,
-	"3530",
 	"OMAP3 Pandora",
 	"NAND",
 };
@@ -200,12 +199,12 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(MMC2_DAT7),		(IEN  | PTU | EN  | M1)) /*MMC2_CLKIN*/\
  MUX_VAL(CP(MMC1_DAT5),		(IEN  | PTD | DIS | M4)) /*GPIO_127 - MMC2_WP*/\
  /*SDIO Interface to WIFI Module*/\
- MUX_VAL(CP(ETK_CLK_ES2),	(IDIS | PTU | EN  | M2)) /*MMC3_CLK*/\
- MUX_VAL(CP(ETK_CTL_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_CMD*/\
- MUX_VAL(CP(ETK_D4_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_DAT0*/\
- MUX_VAL(CP(ETK_D5_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_DAT1*/\
- MUX_VAL(CP(ETK_D6_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_DAT2*/\
- MUX_VAL(CP(ETK_D3_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_DAT3*/\
+ MUX_VAL(CP(ETK_CLK_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_CLK*/\
+ MUX_VAL(CP(ETK_CTL_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_CMD*/\
+ MUX_VAL(CP(ETK_D4_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT0*/\
+ MUX_VAL(CP(ETK_D5_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT1*/\
+ MUX_VAL(CP(ETK_D6_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT2*/\
+ MUX_VAL(CP(ETK_D3_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT3*/\
  /*Audio Interface To Bluetooth chip*/\
  MUX_VAL(CP(MCBSP3_DX),		(IDIS | PTD | DIS | M0)) /*McBSP3_DX*/\
  MUX_VAL(CP(MCBSP3_DR),		(IEN  | PTD | DIS | M0)) /*McBSP3_DR*/\
diff --git a/board/omap3/zoom1/zoom1.h b/board/omap3/zoom1/zoom1.h
index d389492..bc8fba8 100644
--- a/board/omap3/zoom1/zoom1.h
+++ b/board/omap3/zoom1/zoom1.h
@@ -31,7 +31,6 @@ const omap3_sysinfo sysinfo = {
 	SDP_3430_V1,
 	SDP_3430_V2,
 	DDR_STACKED,
-	"3430",
 	"OMAP3 Zoom MDK Rev 1",
 	"NAND",
 };
diff --git a/board/st/nmdk8815/nmdk8815.c b/board/st/nmdk8815/nmdk8815.c
index c54eac1..edf4626 100644
--- a/board/st/nmdk8815/nmdk8815.c
+++ b/board/st/nmdk8815/nmdk8815.c
@@ -49,8 +49,11 @@ int board_init(void)
 	writel(0x00000000, NOMADIK_GPIO1_BASE + 0x28);
 	writel(readl(NOMADIK_SRC_BASE) | 0x8000, NOMADIK_SRC_BASE);
 
-	icache_enable();
+	/* Set up SMCS1 for Ethernet: sram-like, enabled, timing values */
+	writel(0x0000305b, REG_FSMC_BCR1);
+	writel(0x00033f33, REG_FSMC_BTR1);
 
+	icache_enable();
 	return 0;
 }
 
diff --git a/common/devices.c b/common/devices.c
index 38f1bbc..ba53c9b 100644
--- a/common/devices.c
+++ b/common/devices.c
@@ -215,6 +215,9 @@ int devices_init (void)
 	/* Initialize the list */
 	INIT_LIST_HEAD(&(devs.list));
 
+#ifdef CONFIG_ARM_DCC_MULTI
+	drv_arm_dcc_init ();
+#endif
 #if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
 	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
 #endif
diff --git a/cpu/arm_cortexa8/omap3/sys_info.c b/cpu/arm_cortexa8/omap3/sys_info.c
index ab012b6..28a1020 100644
--- a/cpu/arm_cortexa8/omap3/sys_info.c
+++ b/cpu/arm_cortexa8/omap3/sys_info.c
@@ -37,6 +37,14 @@ static sdrc_t *sdrc_base = (sdrc_t *)OMAP34XX_SDRC_BASE;
 static ctrl_t *ctrl_base = (ctrl_t *)OMAP34XX_CTRL_BASE;
 
 /******************************************
+ * get_cpu_type(void) - extract cpu info
+ ******************************************/
+u32 get_cpu_type(void)
+{
+	return readl(&ctrl_base->ctrl_omap_stat);
+}
+
+/******************************************
  * get_cpu_rev(void) - extract version info
  ******************************************/
 u32 get_cpu_rev(void)
@@ -156,7 +164,25 @@ u32 get_board_rev(void)
  *********************************************************************/
 void display_board_info(u32 btype)
 {
-	char *mem_s, *sec_s;
+	char *cpu_s, *mem_s, *sec_s;
+
+	switch (get_cpu_type()) {
+	case OMAP3503:
+		cpu_s = "3503";
+		break;
+	case OMAP3515:
+		cpu_s = "3515";
+		break;
+	case OMAP3525:
+		cpu_s = "3525";
+		break;
+	case OMAP3530:
+		cpu_s = "3530";
+		break;
+	default:
+		cpu_s = "35XX";
+		break;
+	}
 
 	if (is_mem_sdr())
 		mem_s = "mSDR";
@@ -180,7 +206,8 @@ void display_board_info(u32 btype)
 		sec_s = "?";
 	}
 
-	printf("OMAP%s-%s rev %d, CPU-OPP2 L3-165MHz\n", sysinfo.cpu_string,
+
+	printf("OMAP%s-%s rev %d, CPU-OPP2 L3-165MHz\n", cpu_s,
 	       sec_s, get_cpu_rev());
 	printf("%s + %s/%s\n", sysinfo.board_string,
 	       mem_s, sysinfo.nand_string);
diff --git a/drivers/mmc/omap3_mmc.c b/drivers/mmc/omap3_mmc.c
index 399c57b..e90db7e 100644
--- a/drivers/mmc/omap3_mmc.c
+++ b/drivers/mmc/omap3_mmc.c
@@ -28,6 +28,7 @@
 #include <mmc.h>
 #include <part.h>
 #include <i2c.h>
+#include <asm/io.h>
 #include <asm/arch/mmc.h>
 
 const unsigned short mmc_transspeed_val[15][4] = {
@@ -50,6 +51,7 @@ const unsigned short mmc_transspeed_val[15][4] = {
 
 mmc_card_data cur_card_data;
 static block_dev_desc_t mmc_blk_dev;
+static hsmmc_t *mmc_base = (hsmmc_t *)OMAP_HSMMC_BASE;
 
 block_dev_desc_t *mmc_get_dev(int dev)
 {
@@ -60,55 +62,49 @@ void twl4030_mmc_config(void)
 {
 	unsigned char data;
 
-	data = 0x20;
-	i2c_write(0x4B, 0x82, 1, &data, 1);
-	data = 0x2;
-	i2c_write(0x4B, 0x85, 1, &data, 1);
+	data = DEV_GRP_P1;
+	i2c_write(PWRMGT_ADDR_ID4, VMMC1_DEV_GRP, 1, &data, 1);
+	data = VMMC1_VSEL_30;
+	i2c_write(PWRMGT_ADDR_ID4, VMMC1_DEDICATED, 1, &data, 1);
 }
 
 unsigned char mmc_board_init(void)
 {
-	unsigned int value = 0;
+	t2_t *t2_base = (t2_t *)T2_BASE;
 
 	twl4030_mmc_config();
 
-	value = CONTROL_PBIAS_LITE;
-	CONTROL_PBIAS_LITE = value | (1 << 2) | (1 << 1) | (1 << 9);
+	writel(readl(&t2_base->pbias_lite) | PBIASLITEPWRDNZ1 |
+		PBIASSPEEDCTRL0 | PBIASLITEPWRDNZ0,
+		&t2_base->pbias_lite);
 
-	value = CONTROL_DEV_CONF0;
-	CONTROL_DEV_CONF0 = value | (1 << 24);
+	writel(readl(&t2_base->devconf0) | MMCSDIO1ADPCLKISEL,
+		&t2_base->devconf0);
 
 	return 1;
 }
 
 void mmc_init_stream(void)
 {
-	volatile unsigned int mmc_stat;
+	writel(readl(&mmc_base->con) | INIT_INITSTREAM, &mmc_base->con);
 
-	OMAP_HSMMC_CON |= INIT_INITSTREAM;
+	writel(MMC_CMD0, &mmc_base->cmd);
+	while (!(readl(&mmc_base->stat) & CC_MASK));
 
-	OMAP_HSMMC_CMD = MMC_CMD0;
-	do {
-		mmc_stat = OMAP_HSMMC_STAT;
-	} while (!(mmc_stat & CC_MASK));
-
-	OMAP_HSMMC_STAT = CC_MASK;
+	writel(CC_MASK, &mmc_base->stat);
 
-	OMAP_HSMMC_CMD = MMC_CMD0;
-	do {
-		mmc_stat = OMAP_HSMMC_STAT;
-	} while (!(mmc_stat & CC_MASK));
+	writel(MMC_CMD0, &mmc_base->cmd);
+	while (!(readl(&mmc_base->stat) & CC_MASK));
 
-	OMAP_HSMMC_STAT = OMAP_HSMMC_STAT;
-	OMAP_HSMMC_CON &= ~INIT_INITSTREAM;
+	writel(readl(&mmc_base->con) & ~INIT_INITSTREAM, &mmc_base->con);
 }
 
 unsigned char mmc_clock_config(unsigned int iclk, unsigned short clk_div)
 {
 	unsigned int val;
 
-	mmc_reg_out(OMAP_HSMMC_SYSCTL, (ICE_MASK | DTO_MASK | CEN_MASK),
-		    (ICE_STOP | DTO_15THDTO | CEN_DISABLE));
+	mmc_reg_out(&mmc_base->sysctl, (ICE_MASK | DTO_MASK | CEN_MASK),
+			(ICE_STOP | DTO_15THDTO | CEN_DISABLE));
 
 	switch (iclk) {
 	case CLK_INITSEQ:
@@ -123,12 +119,12 @@ unsigned char mmc_clock_config(unsigned int iclk, unsigned short clk_div)
 	default:
 		return 0;
 	}
-	mmc_reg_out(OMAP_HSMMC_SYSCTL,
-		    ICE_MASK | CLKD_MASK, (val << CLKD_OFFSET) | ICE_OSCILLATE);
+	mmc_reg_out(&mmc_base->sysctl, ICE_MASK | CLKD_MASK,
+			(val << CLKD_OFFSET) | ICE_OSCILLATE);
 
-	while ((OMAP_HSMMC_SYSCTL & ICS_MASK) == ICS_NOTREADY) ;
+	while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY);
 
-	OMAP_HSMMC_SYSCTL |= CEN_ENABLE;
+	writel(readl(&mmc_base->sysctl) | CEN_ENABLE, &mmc_base->sysctl);
 	return 1;
 }
 
@@ -138,59 +134,63 @@ unsigned char mmc_init_setup(void)
 
 	mmc_board_init();
 
-	OMAP_HSMMC_SYSCONFIG |= MMC_SOFTRESET;
-	while ((OMAP_HSMMC_SYSSTATUS & RESETDONE) == 0) ;
+	writel(readl(&mmc_base->sysconfig) | MMC_SOFTRESET,
+		&mmc_base->sysconfig);
+	while ((readl(&mmc_base->sysstatus) & RESETDONE) == 0);
 
-	OMAP_HSMMC_SYSCTL |= SOFTRESETALL;
-	while ((OMAP_HSMMC_SYSCTL & SOFTRESETALL) != 0x0) ;
+	writel(readl(&mmc_base->sysctl) | SOFTRESETALL, &mmc_base->sysctl);
+	while ((readl(&mmc_base->sysctl) & SOFTRESETALL) != 0x0);
 
-	OMAP_HSMMC_HCTL = DTW_1_BITMODE | SDBP_PWROFF | SDVS_3V0;
-	OMAP_HSMMC_CAPA |= VS30_3V0SUP | VS18_1V8SUP;
+	writel(DTW_1_BITMODE | SDBP_PWROFF | SDVS_3V0, &mmc_base->hctl);
+	writel(readl(&mmc_base->capa) | VS30_3V0SUP | VS18_1V8SUP,
+		&mmc_base->capa);
 
-	reg_val = OMAP_HSMMC_CON & RESERVED_MASK;
+	reg_val = readl(&mmc_base->con) & RESERVED_MASK;
 
-	OMAP_HSMMC_CON = CTPL_MMC_SD | reg_val | WPP_ACTIVEHIGH |
-		CDP_ACTIVEHIGH | MIT_CTO | DW8_1_4BITMODE | MODE_FUNC |
-		STR_BLOCK | HR_NOHOSTRESP | INIT_NOINIT | NOOPENDRAIN;
+	writel(CTPL_MMC_SD | reg_val | WPP_ACTIVEHIGH | CDP_ACTIVEHIGH |
+		MIT_CTO | DW8_1_4BITMODE | MODE_FUNC | STR_BLOCK |
+		HR_NOHOSTRESP | INIT_NOINIT | NOOPENDRAIN, &mmc_base->con);
 
 	mmc_clock_config(CLK_INITSEQ, 0);
-	OMAP_HSMMC_HCTL |= SDBP_PWRON;
+	writel(readl(&mmc_base->hctl) | SDBP_PWRON, &mmc_base->hctl);
 
-	OMAP_HSMMC_IE = 0x307f0033;
+	writel(IE_BADA | IE_CERR | IE_DEB | IE_DCRC | IE_DTO | IE_CIE |
+		IE_CEB | IE_CCRC | IE_CTO | IE_BRR | IE_BWR | IE_TC | IE_CC,
+		&mmc_base->ie);
 
 	mmc_init_stream();
 	return 1;
 }
 
 unsigned char mmc_send_cmd(unsigned int cmd, unsigned int arg,
-			   unsigned int *response)
+				unsigned int *response)
 {
-	volatile unsigned int mmc_stat;
+	unsigned int mmc_stat;
 
-	while ((OMAP_HSMMC_PSTATE & DATI_MASK) == DATI_CMDDIS) ;
+	while ((readl(&mmc_base->pstate) & DATI_MASK) == DATI_CMDDIS);
 
-	OMAP_HSMMC_BLK = BLEN_512BYTESLEN | NBLK_STPCNT;
-	OMAP_HSMMC_STAT = 0xFFFFFFFF;
-	OMAP_HSMMC_ARG = arg;
-	OMAP_HSMMC_CMD = cmd | CMD_TYPE_NORMAL | CICE_NOCHECK |
-	    CCCE_NOCHECK | MSBS_SGLEBLK | ACEN_DISABLE | BCE_DISABLE |
-	    DE_DISABLE;
+	writel(BLEN_512BYTESLEN | NBLK_STPCNT, &mmc_base->blk);
+	writel(0xFFFFFFFF, &mmc_base->stat);
+	writel(arg, &mmc_base->arg);
+	writel(cmd | CMD_TYPE_NORMAL | CICE_NOCHECK | CCCE_NOCHECK |
+		MSBS_SGLEBLK | ACEN_DISABLE | BCE_DISABLE | DE_DISABLE,
+		&mmc_base->cmd);
 
 	while (1) {
 		do {
-			mmc_stat = OMAP_HSMMC_STAT;
+			mmc_stat = readl(&mmc_base->stat);
 		} while (mmc_stat == 0);
 
 		if ((mmc_stat & ERRI_MASK) != 0)
 			return (unsigned char) mmc_stat;
 
 		if (mmc_stat & CC_MASK) {
-			OMAP_HSMMC_STAT = CC_MASK;
-			response[0] = OMAP_HSMMC_RSP10;
+			writel(CC_MASK, &mmc_base->stat);
+			response[0] = readl(&mmc_base->rsp10);
 			if ((cmd & RSP_TYPE_MASK) == RSP_TYPE_LGHT136) {
-				response[1] = OMAP_HSMMC_RSP32;
-				response[2] = OMAP_HSMMC_RSP54;
-				response[3] = OMAP_HSMMC_RSP76;
+				response[1] = readl(&mmc_base->rsp32);
+				response[2] = readl(&mmc_base->rsp54);
+				response[3] = readl(&mmc_base->rsp76);
 			}
 			break;
 		}
@@ -200,7 +200,7 @@ unsigned char mmc_send_cmd(unsigned int cmd, unsigned int arg,
 
 unsigned char mmc_read_data(unsigned int *output_buf)
 {
-	volatile unsigned int mmc_stat;
+	unsigned int mmc_stat;
 	unsigned int read_count = 0;
 
 	/*
@@ -208,7 +208,7 @@ unsigned char mmc_read_data(unsigned int *output_buf)
 	 */
 	while (1) {
 		do {
-			mmc_stat = OMAP_HSMMC_STAT;
+			mmc_stat = readl(&mmc_base->stat);
 		} while (mmc_stat == 0);
 
 		if ((mmc_stat & ERRI_MASK) != 0)
@@ -217,19 +217,22 @@ unsigned char mmc_read_data(unsigned int *output_buf)
 		if (mmc_stat & BRR_MASK) {
 			unsigned int k;
 
-			OMAP_HSMMC_STAT |= BRR_MASK;
+			writel(readl(&mmc_base->stat) | BRR_MASK,
+				&mmc_base->stat);
 			for (k = 0; k < MMCSD_SECTOR_SIZE / 4; k++) {
-				*output_buf = OMAP_HSMMC_DATA;
+				*output_buf = readl(&mmc_base->data);
 				output_buf++;
 				read_count += 4;
 			}
 		}
 
 		if (mmc_stat & BWR_MASK)
-			OMAP_HSMMC_STAT |= BWR_MASK;
+			writel(readl(&mmc_base->stat) | BWR_MASK,
+				&mmc_base->stat);
 
 		if (mmc_stat & TC_MASK) {
-			OMAP_HSMMC_STAT |= TC_MASK;
+			writel(readl(&mmc_base->stat) | TC_MASK,
+				&mmc_base->stat);
 			break;
 		}
 	}
@@ -273,8 +276,8 @@ unsigned char mmc_detect_card(mmc_card_data *mmc_card_cur)
 		mmc_card_cur->card_type = MMC_CARD;
 		ocr_value |= MMC_OCR_REG_ACCESS_MODE_SECTOR;
 		ret_cmd41 = MMC_CMD1;
-		OMAP_HSMMC_CON &= ~OD;
-		OMAP_HSMMC_CON |= OPENDRAIN;
+		writel(readl(&mmc_base->con) & ~OD, &mmc_base->con);
+		writel(readl(&mmc_base->con) | OPENDRAIN, &mmc_base->con);
 	}
 
 	argument = ocr_value;
@@ -342,8 +345,8 @@ unsigned char mmc_detect_card(mmc_card_data *mmc_card_cur)
 		mmc_card_cur->RCA = ((mmc_resp_r6 *) resp)->newpublishedrca;
 	}
 
-	OMAP_HSMMC_CON &= ~OD;
-	OMAP_HSMMC_CON |= NOOPENDRAIN;
+	writel(readl(&mmc_base->con) & ~OD, &mmc_base->con);
+	writel(readl(&mmc_base->con) | NOOPENDRAIN, &mmc_base->con);
 	return 1;
 }
 
@@ -518,7 +521,7 @@ unsigned long mmc_bread(int dev_num, unsigned long blknr, lbaint_t blkcnt,
 			void *dst)
 {
 	omap_mmc_read_sect(blknr, (blkcnt * MMCSD_SECTOR_SIZE), &cur_card_data,
-			   (unsigned long *) dst);
+				(unsigned long *) dst);
 	return 1;
 }
 
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 24edb27..5974d77 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -38,6 +38,7 @@ endif
 COBJS-$(CONFIG_DRIVER_NAND_BFIN) += bfin_nand.o
 COBJS-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o
 COBJS-$(CONFIG_NAND_FSL_UPM) += fsl_upm.o
+COBJS-$(CONFIG_NAND_NOMADIK) += nomadik.o
 COBJS-$(CONFIG_NAND_S3C64XX) += s3c64xx.o
 COBJS-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o
 endif
diff --git a/drivers/mtd/nand/nomadik.c b/drivers/mtd/nand/nomadik.c
new file mode 100644
index 0000000..b76f4cb
--- /dev/null
+++ b/drivers/mtd/nand/nomadik.c
@@ -0,0 +1,221 @@
+/*
+ * (C) Copyright 2007 STMicroelectronics, <www.st.com>
+ * (C) Copyright 2009 Alessandro Rubini <rubini@unipv.it>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <nand.h>
+#include <asm/io.h>
+
+static inline int parity(int b) /* b is really a byte; returns 0 or ~0 */
+{
+	__asm__ __volatile__(
+		"eor   %0, %0, %0, lsr #4\n\t"
+		"eor   %0, %0, %0, lsr #2\n\t"
+		"eor   %0, %0, %0, lsr #1\n\t"
+		"ands  %0, %0, #1\n\t"
+		"subne %0, %0, #2\t"
+		: "=r" (b) : "0" (b));
+	return b;
+}
+
+/*
+ * This is the ECC routine used in hardware, according to the manual.
+ * HW claims to make the calculation but not the correction; so we must
+ * recalculate the bytes for a comparison.
+ */
+static int ecc512(const unsigned char *data, unsigned char *ecc)
+{
+	int gpar = 0;
+	int i, val, par;
+	int pbits = 0;		/* P8, P16, ... P2048 */
+	int pprime = 0;		/* P8', P16', ... P2048' */
+	int lowbits;		/* P1, P2, P4 and primes */
+
+	for (i = 0; i < 512; i++) {
+		par = parity((val = data[i]));
+		gpar ^= val;
+		pbits ^= (i & par);
+	}
+	/*
+	 * Ok, now gpar is global parity (xor of all bytes)
+	 * pbits are all the parity bits (non-prime ones)
+	 */
+	par = parity(gpar);
+	pprime = pbits ^ par;
+	/* Put low bits in the right position for ecc[2] (bits 7..2) */
+	lowbits = 0
+		| (parity(gpar & 0xf0) & 0x80)	/* P4  */
+		| (parity(gpar & 0x0f) & 0x40)	/* P4' */
+		| (parity(gpar & 0xcc) & 0x20)	/* P2  */
+		| (parity(gpar & 0x33) & 0x10)	/* P2' */
+		| (parity(gpar & 0xaa) & 0x08)	/* P1  */
+		| (parity(gpar & 0x55) & 0x04);	/* P1' */
+
+	ecc[2] = ~(lowbits | ((pbits & 0x100) >> 7) | ((pprime & 0x100) >> 8));
+	/* now intermix bits for ecc[1] (P1024..P128') and ecc[0] (P64..P8') */
+	ecc[1] = ~(    (pbits & 0x80) >> 0  | ((pprime & 0x80) >> 1)
+		    | ((pbits & 0x40) >> 1) | ((pprime & 0x40) >> 2)
+		    | ((pbits & 0x20) >> 2) | ((pprime & 0x20) >> 3)
+		    | ((pbits & 0x10) >> 3) | ((pprime & 0x10) >> 4));
+
+	ecc[0] = ~(    (pbits & 0x8) << 4  | ((pprime & 0x8) << 3)
+		    | ((pbits & 0x4) << 3) | ((pprime & 0x4) << 2)
+		    | ((pbits & 0x2) << 2) | ((pprime & 0x2) << 1)
+		    | ((pbits & 0x1) << 1) | ((pprime & 0x1) << 0));
+	return 0;
+}
+
+/* This is the method in the chip->ecc field */
+static int nomadik_ecc_calculate(struct mtd_info *mtd, const uint8_t *dat,
+				 uint8_t *ecc_code)
+{
+	return ecc512(dat, ecc_code);
+}
+
+static int nomadik_ecc_correct(struct mtd_info *mtd, uint8_t *dat,
+				uint8_t *r_ecc, uint8_t *c_ecc)
+{
+	struct nand_chip *chip = mtd->priv;
+	uint32_t r, c, d, diff; /*read, calculated, xor of them */
+
+	if (!memcmp(r_ecc, c_ecc, chip->ecc.bytes))
+		return 0;
+
+	/* Reorder the bytes into ascending-order 24 bits -- see manual */
+	r = r_ecc[2] << 22 | r_ecc[1] << 14 | r_ecc[0] << 6 | r_ecc[2] >> 2;
+	c = c_ecc[2] << 22 | c_ecc[1] << 14 | c_ecc[0] << 6 | c_ecc[2] >> 2;
+	diff = (r ^ c) & ((1<<24)-1); /* use 24 bits only */
+
+	/* If 12 bits are different, one per pair, it's correctable */
+	if (((diff | (diff>>1)) & 0x555555) == 0x555555) {
+		int bit = ((diff & 2) >> 1)
+			| ((diff & 0x8) >> 2) | ((diff & 0x20) >> 3);
+		int byte;
+
+		d = diff >> 6; /* remove bit-order info */
+		byte =  ((d & 2) >> 1)
+			| ((d & 0x8) >> 2) | ((d & 0x20) >> 3)
+			| ((d & 0x80) >> 4) | ((d & 0x200) >> 5)
+			| ((d & 0x800) >> 6) | ((d & 0x2000) >> 7)
+			| ((d & 0x8000) >> 8) | ((d & 0x20000) >> 9);
+		/* correct the single bit */
+		dat[byte] ^= 1<<bit;
+		return 0;
+	}
+	/* If 1 bit only differs, it's one bit error in ECC, ignore */
+	if ((diff ^ (1 << (ffs(diff) - 1))) == 0)
+		return 0;
+	/* Otherwise, uncorrectable */
+	return -1;
+}
+
+static void nomadik_ecc_hwctl(struct mtd_info *mtd, int mode)
+{ /* mandatory in the structure but not used here */ }
+
+
+/* This is the layout used by older installations, we keep compatible */
+struct nand_ecclayout nomadik_ecc_layout = {
+	.eccbytes = 3 * 4,
+	.eccpos = { /* each subpage has 16 bytes: pos 2,3,4 hosts ECC */
+		0x02, 0x03, 0x04,
+		0x12, 0x13, 0x14,
+		0x22, 0x23, 0x24,
+		0x32, 0x33, 0x34},
+	.oobfree = { {0x08, 0x08}, {0x18, 0x08}, {0x28, 0x08}, {0x38, 0x08} },
+};
+
+#define MASK_ALE	(1 << 24)	/* our ALE is AD21 */
+#define MASK_CLE	(1 << 23)	/* our CLE is AD22 */
+
+/* This is copied from the AT91SAM9 devices (Stelian Pop, Lead Tech Design) */
+static void nomadik_nand_hwcontrol(struct mtd_info *mtd,
+				   int cmd, unsigned int ctrl)
+{
+	struct nand_chip *this = mtd->priv;
+	u32 pcr0 = readl(REG_FSMC_PCR0);
+
+	if (ctrl & NAND_CTRL_CHANGE) {
+		ulong IO_ADDR_W = (ulong) this->IO_ADDR_W;
+		IO_ADDR_W &= ~(MASK_ALE | MASK_CLE);
+
+		if (ctrl & NAND_CLE)
+			IO_ADDR_W |= MASK_CLE;
+		if (ctrl & NAND_ALE)
+			IO_ADDR_W |= MASK_ALE;
+
+		if (ctrl & NAND_NCE)
+			writel(pcr0 | 0x4, REG_FSMC_PCR0);
+		else
+			writel(pcr0 & ~0x4, REG_FSMC_PCR0);
+
+		this->IO_ADDR_W = (void *) IO_ADDR_W;
+		this->IO_ADDR_R = (void *) IO_ADDR_W;
+	}
+
+	if (cmd != NAND_CMD_NONE)
+		writeb(cmd, this->IO_ADDR_W);
+}
+
+/* Returns 1 when ready; upper layers timeout at 20ms with timer routines */
+static int nomadik_nand_ready(struct mtd_info *mtd)
+{
+	return 1; /* The ready bit is handled in hardware */
+}
+
+/* Copy a buffer 32bits at a time: faster than defualt method which is 8bit */
+static void nomadik_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+	int i;
+	struct nand_chip *chip = mtd->priv;
+	u32 *p = (u32 *) buf;
+
+	len >>= 2;
+	writel(0, REG_FSMC_ECCR0);
+	for (i = 0; i < len; i++)
+		p[i] = readl(chip->IO_ADDR_R);
+}
+
+int board_nand_init(struct nand_chip *chip)
+{
+	/* Set up the FSMC_PCR0 for nand access*/
+	writel(0x0000004a, REG_FSMC_PCR0);
+	/* Set up FSMC_PMEM0, FSMC_PATT0 with timing data for access */
+	writel(0x00020401, REG_FSMC_PMEM0);
+	writel(0x00020404, REG_FSMC_PATT0);
+
+	chip->options = NAND_COPYBACK |	NAND_CACHEPRG | NAND_NO_PADDING;
+	chip->cmd_ctrl = nomadik_nand_hwcontrol;
+	chip->dev_ready = nomadik_nand_ready;
+	/* The chip allows 32bit reads, so avoid the default 8bit copy */
+	chip->read_buf = nomadik_nand_read_buf;
+
+	/* ECC: follow the hardware-defined rulse, but do it in sw */
+	chip->ecc.mode = NAND_ECC_HW;
+	chip->ecc.bytes = 3;
+	chip->ecc.size = 512;
+	chip->ecc.layout = &nomadik_ecc_layout;
+	chip->ecc.calculate = nomadik_ecc_calculate;
+	chip->ecc.hwctl = nomadik_ecc_hwctl;
+	chip->ecc.correct = nomadik_ecc_correct;
+
+	return 0;
+}
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 0f980ab..d0efd73 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -25,6 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	:= $(obj)libserial.a
 
+COBJS-$(CONFIG_ARM_DCC) += arm_dcc.o
 COBJS-$(CONFIG_ATMEL_USART) += atmel_usart.o
 COBJS-$(CONFIG_MCFUART) += mcfuart.o
 COBJS-$(CONFIG_NS9750_UART) += ns9750_serial.o
diff --git a/drivers/serial/arm_dcc.c b/drivers/serial/arm_dcc.c
new file mode 100644
index 0000000..5a7fb6b
--- /dev/null
+++ b/drivers/serial/arm_dcc.c
@@ -0,0 +1,226 @@
+/*
+ * Copyright (C) 2004-2007 ARM Limited.
+ * Copyright (C) 2008 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * As a special exception, if other files instantiate templates or use macros
+ * or inline functions from this file, or you compile this file and link it
+ * with other works to produce a work based on this file, this file does not
+ * by itself cause the resulting work to be covered by the GNU General Public
+ * License. However the source code for this file must still be made available
+ * in accordance with section (3) of the GNU General Public License.
+
+ * This exception does not invalidate any other reasons why a work based on
+ * this file might be covered by the GNU General Public License.
+ */
+
+#include <common.h>
+#include <devices.h>
+
+#define DCC_ARM9_RBIT	(1 << 0)
+#define DCC_ARM9_WBIT	(1 << 1)
+#define DCC_ARM11_RBIT	(1 << 30)
+#define DCC_ARM11_WBIT	(1 << 29)
+
+#define read_core_id(x)	do {						\
+		__asm__ ("mrc p15, 0, %0, c0, c0, 0\n" : "=r" (x));	\
+		x = (x >> 4) & 0xFFF;					\
+		} while (0);
+
+/*
+ * ARM9
+ */
+#define write_arm9_dcc(x)	\
+		__asm__ volatile ("mcr p14, 0, %0, c1, c0, 0\n" : : "r" (x))
+
+#define read_arm9_dcc(x)	\
+		__asm__ volatile ("mrc p14, 0, %0, c1, c0, 0\n" : "=r" (x))
+
+#define status_arm9_dcc(x)	\
+		__asm__ volatile ("mrc p14, 0, %0, c0, c0, 0\n" : "=r" (x))
+
+#define can_read_arm9_dcc(x)	do {	\
+		status_arm9_dcc(x);	\
+		x &= DCC_ARM9_RBIT;	\
+		} while (0);
+
+#define can_write_arm9_dcc(x)	do {	\
+		status_arm9_dcc(x);	\
+		x &= DCC_ARM9_WBIT;	\
+		x = (x == 0);		\
+		} while (0);
+
+/*
+ * ARM11
+ */
+#define write_arm11_dcc(x)	\
+		__asm__ volatile ("mcr p14, 0, %0, c0, c5, 0\n" : : "r" (x))
+
+#define read_arm11_dcc(x)	\
+		__asm__ volatile ("mrc p14, 0, %0, c0, c5, 0\n" : "=r" (x))
+
+#define status_arm11_dcc(x)	\
+		__asm__ volatile ("mrc p14, 0, %0, c0, c1, 0\n" : "=r" (x))
+
+#define can_read_arm11_dcc(x)	do {	\
+		status_arm11_dcc(x);	\
+		x &= DCC_ARM11_RBIT;	\
+		} while (0);
+
+#define can_write_arm11_dcc(x)	do {	\
+		status_arm11_dcc(x);	\
+		x &= DCC_ARM11_WBIT;	\
+		x = (x == 0);		\
+		} while (0);
+
+#define TIMEOUT_COUNT 0x4000000
+
+static enum {
+	arm9_and_earlier,
+	arm11_and_later
+} arm_type = arm9_and_earlier;
+
+#ifndef CONFIG_ARM_DCC_MULTI
+#define arm_dcc_init serial_init
+void serial_setbrg(void) {}
+#define arm_dcc_getc serial_getc
+#define arm_dcc_putc serial_putc
+#define arm_dcc_puts serial_puts
+#define arm_dcc_tstc serial_tstc
+#endif
+
+int arm_dcc_init(void)
+{
+	register unsigned int id;
+
+	read_core_id(id);
+
+	if (id >= 0xb00)
+		arm_type = arm11_and_later;
+	else
+		arm_type = arm9_and_earlier;
+
+	return 0;
+}
+
+int arm_dcc_getc(void)
+{
+	int ch;
+	register unsigned int reg;
+
+	switch (arm_type) {
+	case arm11_and_later:
+		do {
+			can_read_arm11_dcc(reg);
+		} while (!reg);
+		read_arm11_dcc(ch);
+		break;
+
+	case arm9_and_earlier:
+	default:
+		do {
+			can_read_arm9_dcc(reg);
+		} while (!reg);
+		read_arm9_dcc(ch);
+		break;
+	}
+
+	return ch;
+}
+
+void arm_dcc_putc(char ch)
+{
+	register unsigned int reg;
+	unsigned int timeout_count = TIMEOUT_COUNT;
+
+	switch (arm_type) {
+	case arm11_and_later:
+		while (--timeout_count) {
+			can_write_arm11_dcc(reg);
+			if (reg)
+				break;
+		}
+		if (timeout_count == 0)
+			return;
+		else
+			write_arm11_dcc(ch);
+		break;
+
+	case arm9_and_earlier:
+	default:
+		while (--timeout_count) {
+			can_write_arm9_dcc(reg);
+			if (reg)
+				break;
+		}
+		if (timeout_count == 0)
+			return;
+		else
+			write_arm9_dcc(ch);
+		break;
+	}
+}
+
+void arm_dcc_puts(const char *s)
+{
+	while (*s)
+		arm_dcc_putc(*s++);
+}
+
+int arm_dcc_tstc(void)
+{
+	register unsigned int reg;
+
+	switch (arm_type) {
+	case arm11_and_later:
+		can_read_arm11_dcc(reg);
+		break;
+	case arm9_and_earlier:
+	default:
+		can_read_arm9_dcc(reg);
+		break;
+	}
+
+	return reg;
+}
+
+#ifdef CONFIG_ARM_DCC_MULTI
+static device_t arm_dcc_dev;
+
+int drv_arm_dcc_init(void)
+{
+	int rc;
+
+	/* Device initialization */
+	memset(&arm_dcc_dev, 0, sizeof(arm_dcc_dev));
+
+	strcpy(arm_dcc_dev.name, "dcc");
+	arm_dcc_dev.ext = 0;	/* No extensions */
+	arm_dcc_dev.flags = DEV_FLAGS_INPUT | DEV_FLAGS_OUTPUT;
+	arm_dcc_dev.tstc = arm_dcc_tstc;	/* 'tstc' function */
+	arm_dcc_dev.getc = arm_dcc_getc;	/* 'getc' function */
+	arm_dcc_dev.putc = arm_dcc_putc;	/* 'putc' function */
+	arm_dcc_dev.puts = arm_dcc_puts;	/* 'puts' function */
+
+	rc = device_register(&arm_dcc_dev);
+
+	if (rc == 0) {
+		arm_dcc_init();
+		return 1;
+	}
+
+	return 0;
+}
+#endif
diff --git a/include/asm-arm/arch-omap3/cpu.h b/include/asm-arm/arch-omap3/cpu.h
index 69c0b36..5b344f8 100644
--- a/include/asm-arm/arch-omap3/cpu.h
+++ b/include/asm-arm/arch-omap3/cpu.h
@@ -35,11 +35,31 @@ typedef struct ctrl {
 	unsigned short gpmc_nwe;	/* 0xC4 */
 	unsigned char res2[0x22A];
 	unsigned int status;		/* 0x2F0 */
+	unsigned int gpstatus;		/* 0x2F4 */
+	unsigned char res3[0x08];
+	unsigned int rpubkey_0;		/* 0x300 */
+	unsigned int rpubkey_1;		/* 0x304 */
+	unsigned int rpubkey_2;		/* 0x308 */
+	unsigned int rpubkey_3;		/* 0x30C */
+	unsigned int rpubkey_4;		/* 0x310 */
+	unsigned char res4[0x04];
+	unsigned int randkey_0;		/* 0x318 */
+	unsigned int randkey_1;		/* 0x31C */
+	unsigned int randkey_2;		/* 0x320 */
+	unsigned int randkey_3;		/* 0x324 */
+	unsigned char res5[0x124];
+	unsigned int ctrl_omap_stat;	/* 0x44C */
 } ctrl_t;
 #else /* __ASSEMBLY__ */
 #define CONTROL_STATUS		0x2F0
 #endif /* __ASSEMBLY__ */
 
+/* cpu type */
+#define OMAP3503		0x5c00
+#define OMAP3515		0x1c00
+#define OMAP3525		0x4c00
+#define OMAP3530		0x0c00
+
 /* device type */
 #define DEVICE_MASK		(0x7 << 8)
 #define SYSBOOT_MASK		0x1F
diff --git a/include/asm-arm/arch-omap3/mmc_host_def.h b/include/asm-arm/arch-omap3/mmc_host_def.h
index dfb376a..aa751c9 100644
--- a/include/asm-arm/arch-omap3/mmc_host_def.h
+++ b/include/asm-arm/arch-omap3/mmc_host_def.h
@@ -25,30 +25,50 @@
 #ifndef MMC_HOST_DEF_H
 #define MMC_HOST_DEF_H
 
+/* T2 Register definitions */
+#define T2_BASE			0x48002000
+
+typedef struct t2 {
+	unsigned char res1[0x274];
+	unsigned int devconf0;		/* 0x274 */
+	unsigned char res2[0x2A8];
+	unsigned int pbias_lite;	/* 0x520 */
+} t2_t;
+
+#define MMCSDIO1ADPCLKISEL		(1 << 24)
+
+#define PBIASLITEPWRDNZ0		(1 << 1)
+#define PBIASSPEEDCTRL0			(1 << 2)
+#define PBIASLITEPWRDNZ1		(1 << 9)
+
 /*
  * OMAP HSMMC register definitions
  */
-#define OMAP_HSMMC_SYSCONFIG		(*(unsigned int *) 0x4809C010)
-#define OMAP_HSMMC_SYSSTATUS		(*(unsigned int *) 0x4809C014)
-#define OMAP_HSMMC_CON			(*(unsigned int *) 0x4809C02C)
-#define OMAP_HSMMC_BLK			(*(unsigned int *) 0x4809C104)
-#define OMAP_HSMMC_ARG			(*(unsigned int *) 0x4809C108)
-#define OMAP_HSMMC_CMD			(*(unsigned int *) 0x4809C10C)
-#define OMAP_HSMMC_RSP10		(*(unsigned int *) 0x4809C110)
-#define OMAP_HSMMC_RSP32		(*(unsigned int *) 0x4809C114)
-#define OMAP_HSMMC_RSP54		(*(unsigned int *) 0x4809C118)
-#define OMAP_HSMMC_RSP76		(*(unsigned int *) 0x4809C11C)
-#define OMAP_HSMMC_DATA			(*(unsigned int *) 0x4809C120)
-#define OMAP_HSMMC_PSTATE		(*(unsigned int *) 0x4809C124)
-#define OMAP_HSMMC_HCTL			(*(unsigned int *) 0x4809C128)
-#define OMAP_HSMMC_SYSCTL		(*(unsigned int *) 0x4809C12C)
-#define OMAP_HSMMC_STAT			(*(unsigned int *) 0x4809C130)
-#define OMAP_HSMMC_IE			(*(unsigned int *) 0x4809C134)
-#define OMAP_HSMMC_CAPA			(*(unsigned int *) 0x4809C140)
+#define OMAP_HSMMC_BASE		0x4809C000
 
-/* T2 Register definitions */
-#define CONTROL_DEV_CONF0		(*(unsigned int *) 0x48002274)
-#define CONTROL_PBIAS_LITE		(*(unsigned int *) 0x48002520)
+typedef struct hsmmc {
+	unsigned char res1[0x10];
+	unsigned int sysconfig;		/* 0x10 */
+	unsigned int sysstatus;		/* 0x14 */
+	unsigned char res2[0x14];
+	unsigned int con;		/* 0x2C */
+	unsigned char res3[0xD4];
+	unsigned int blk;		/* 0x104 */
+	unsigned int arg;		/* 0x108 */
+	unsigned int cmd;		/* 0x10C */
+	unsigned int rsp10;		/* 0x110 */
+	unsigned int rsp32;		/* 0x114 */
+	unsigned int rsp54;		/* 0x118 */
+	unsigned int rsp76;		/* 0x11C */
+	unsigned int data;		/* 0x120 */
+	unsigned int pstate;		/* 0x124 */
+	unsigned int hctl;		/* 0x128 */
+	unsigned int sysctl;		/* 0x12C */
+	unsigned int stat;		/* 0x130 */
+	unsigned int ie;		/* 0x134 */
+	unsigned char res4[0x8];
+	unsigned int capa;		/* 0x140 */
+} hsmmc_t;
 
 /*
  * OMAP HS MMC Bit definitions
@@ -159,8 +179,6 @@ typedef struct {
 } mmc_card_data;
 
 #define mmc_reg_out(addr, mask, val)\
-	(addr) = (((addr)) & (~(mask))) | ((val) & (mask));
-#define mmc_reg_out(addr, mask, val)\
-	(addr) = (((addr)) & (~(mask))) | ((val) & (mask));
+	writel((readl(addr) & (~(mask))) | ((val) & (mask)), (addr))
 
 #endif /* MMC_HOST_DEF_H */
diff --git a/include/asm-arm/arch-omap3/omap3.h b/include/asm-arm/arch-omap3/omap3.h
index 7473656..02e36d7 100644
--- a/include/asm-arm/arch-omap3/omap3.h
+++ b/include/asm-arm/arch-omap3/omap3.h
@@ -97,7 +97,8 @@ typedef struct s32ktimer {
 typedef struct gpio {
 	unsigned char res1[0x34];
 	unsigned int oe;		/* 0x34 */
-	unsigned char res2[0x58];
+	unsigned int datain;		/* 0x38 */
+	unsigned char res2[0x54];
 	unsigned int cleardataout;	/* 0x90 */
 	unsigned int setdataout;	/* 0x94 */
 } gpio_t;
@@ -202,6 +203,8 @@ typedef struct gpio {
 #define VAUX2_DEDICATED		0x79
 #define VAUX3_DEV_GRP		0x7A
 #define VAUX3_DEDICATED		0x7D
+#define VMMC1_DEV_GRP		0x82
+#define VMMC1_DEDICATED		0x85
 #define VPLL2_DEV_GRP		0x8E
 #define VPLL2_DEDICATED		0x91
 #define VDAC_DEV_GRP		0x96
@@ -214,5 +217,6 @@ typedef struct gpio {
 #define VAUX3_VSEL_28		0x03
 #define VPLL2_VSEL_18		0x05
 #define VDAC_VSEL_18		0x03
+#define VMMC1_VSEL_30		0x02
 
 #endif
diff --git a/include/asm-arm/arch-omap3/sys_proto.h b/include/asm-arm/arch-omap3/sys_proto.h
index 4c624e8..ab3e168 100644
--- a/include/asm-arm/arch-omap3/sys_proto.h
+++ b/include/asm-arm/arch-omap3/sys_proto.h
@@ -25,7 +25,6 @@ typedef struct {
 	u32 board_type_v1;
 	u32 board_type_v2;
 	u32 mtype;
-	char *cpu_string;
 	char *board_string;
 	char *nand_string;
 } omap3_sysinfo;
diff --git a/include/configs/nmdk8815.h b/include/configs/nmdk8815.h
index 01de08f..543780d 100644
--- a/include/configs/nmdk8815.h
+++ b/include/configs/nmdk8815.h
@@ -25,6 +25,8 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#include <nomadik.h>
+
 #define CONFIG_ARM926EJS
 #define CONFIG_NOMADIK
 #define CONFIG_NOMADIK_8815
@@ -35,12 +37,18 @@
 
 /* commands */
 #include <config_cmd_default.h>
+
+#define CONFIG_CMD_NET
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
-/* At this point there is no flash driver, so remove some commands */
-#undef CONFIG_CMD_ENV
+#define CONFIG_CMD_NFS
+/* There is no NOR flash, so undefine these commands */
 #undef CONFIG_CMD_FLASH
 #undef CONFIG_CMD_IMLS
+#define CONFIG_SYS_NO_FLASH
+/* There is NAND storage */
+#define CONFIG_NAND_NOMADIK
+#define CONFIG_CMD_JFFS2
 
 /* user interface */
 #define CONFIG_SYS_LONGHELP
@@ -118,13 +126,11 @@
 #define CONFIG_MTD_ONENAND_VERIFY_WRITE
 #define CONFIG_SYS_ONENAND_BASE		0x30000000
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		0x40000000
-
-#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_NAND_BASE		0x40000000 /* SMPS0n */
 
 #ifdef CONFIG_BOOT_ONENAND
 
-#   undef CONFIG_CMD_NAND /* Temporary: nand and onenand can't coexist */
+#   define CONFIG_CMD_ONENAND /* Temporary: nand and onenand can't coexist */
    /* Partition				Size	Start
     * XloaderTOC + X-Loader		256KB	0x00000000
     * Memory init function		256KB	0x00040000
@@ -142,7 +148,7 @@
 
 #else /* ! CONFIG_BOOT_ONENAND */
 
-#   undef CONFIG_CMD_ONENAND /* Temporary: nand and onenand can't coexist */
+#   define CONFIG_CMD_NAND /* Temporary: nand and onenand can't coexist */
 
 #   define CONFIG_JFFS2_DEV		"nand0"
 #   define CONFIG_JFFS2_NAND		1 /* For the jffs2 support*/
@@ -150,39 +156,13 @@
 #   define CONFIG_JFFS2_PART_OFFSET	0x00280000
 
 #   define CONFIG_ENV_IS_IN_NAND
-#   define CONFIG_ENV_SIZE		0x20000 /*128 Kb*/
+#   define CONFIG_ENV_SIZE		0x20000 /* 128 Kb - one sector */
 #   define CONFIG_ENV_OFFSET		(0x8000000 - CONFIG_ENV_SIZE)
 
 #endif /* CONFIG_BOOT_ONENAND */
 
-/* Temporarily, until we have no driver, env is not in nand */
-#undef CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_IS_NOWHERE
-
 /* this is needed to make hello_world.c and other stuff happy */
 #define CONFIG_SYS_MAX_FLASH_SECT	512
 #define CONFIG_SYS_MAX_FLASH_BANKS	1
 
-/* base addresses of our peripherals */
-#define NOMADIK_SRC_BASE	0x101E0000	/* System and Reset Cnt */
-#define NOMADIK_PMU_BASE	0x101E9000	/* Power Management Unit */
-#define NOMADIK_MPMC_BASE	0x10110000	/* SDRAM Controller */
-#define NOMADIK_FSMC_BASE	0x10100000	/* FSMC Controller */
-#define NOMADIK_1NAND_BASE	0x30000000
-#define NOMADIK_GPIO0_BASE	0x101E4000
-#define NOMADIK_GPIO1_BASE	0x101E5000
-#define NOMADIK_GPIO2_BASE	0x101E6000
-#define NOMADIK_GPIO3_BASE	0x101E7000
-#define NOMADIK_CPLD_BASE	0x36000000
-#define NOMADIK_UART0_BASE	0x101FD000
-#define NOMADIK_UART1_BASE	0x101FB000
-#define NOMADIK_UART2_BASE	0x101F2000
-
-#define NOMADIK_I2C1_BASE	0x101F7000	/* I2C1 interface */
-#define NOMADIK_I2C0_BASE	0x101F8000	/* I2C0 interface */
-
-#define NOMADIK_RTC_BASE	0x101E8000
-#define NOMADIK_ETH0_BASE	0x36800300
-#define NOMADIK_CPLD_UART_BASE	0x36480000
-
 #endif /* __CONFIG_H */
diff --git a/include/devices.h b/include/devices.h
index 84c4514..3a9881b 100644
--- a/include/devices.h
+++ b/include/devices.h
@@ -98,6 +98,9 @@ struct list_head* device_get_list(void);
 device_t* device_get_by_name(char* name);
 device_t* device_clone(device_t *dev);
 
+#ifdef CONFIG_ARM_DCC_MULTI
+int drv_arm_dcc_init(void);
+#endif
 #ifdef CONFIG_LCD
 int	drv_lcd_init (void);
 #endif
diff --git a/include/nomadik.h b/include/nomadik.h
new file mode 100644
index 0000000..d9405fd
--- /dev/null
+++ b/include/nomadik.h
@@ -0,0 +1,39 @@
+/* Collection of constants used to access Nomadik registers */
+
+#ifndef __NOMADIK_H__
+#define __NOMADIK_H__
+
+/* Base addresses of our peripherals */
+#define NOMADIK_SRC_BASE	0x101E0000	/* System and Reset Cnt */
+#define NOMADIK_PMU_BASE	0x101E9000	/* Power Management Unit */
+#define NOMADIK_MPMC_BASE	0x10110000	/* SDRAM Controller */
+#define NOMADIK_FSMC_BASE	0x10100000	/* FSMC Controller */
+#define NOMADIK_1NAND_BASE	0x30000000
+#define NOMADIK_GPIO0_BASE	0x101E4000
+#define NOMADIK_GPIO1_BASE	0x101E5000
+#define NOMADIK_GPIO2_BASE	0x101E6000
+#define NOMADIK_GPIO3_BASE	0x101E7000
+#define NOMADIK_CPLD_BASE	0x36000000
+#define NOMADIK_UART0_BASE	0x101FD000
+#define NOMADIK_UART1_BASE	0x101FB000
+#define NOMADIK_UART2_BASE	0x101F2000
+
+#define NOMADIK_I2C1_BASE	0x101F7000	/* I2C1 interface */
+#define NOMADIK_I2C0_BASE	0x101F8000	/* I2C0 interface */
+
+#define NOMADIK_RTC_BASE	0x101E8000
+#define NOMADIK_ETH0_BASE	0x36800300
+#define NOMADIK_CPLD_UART_BASE	0x36480000
+
+/* Chip select registers ("Flexible Static Memory Controller") */
+
+#define REG_FSMC_BCR0	(NOMADIK_FSMC_BASE + 0x00)
+#define REG_FSMC_BTR0	(NOMADIK_FSMC_BASE + 0x04)
+#define REG_FSMC_BCR1	(NOMADIK_FSMC_BASE + 0x08)
+#define REG_FSMC_BTR1	(NOMADIK_FSMC_BASE + 0x0c)
+#define REG_FSMC_PCR0	(NOMADIK_FSMC_BASE + 0x40)
+#define REG_FSMC_PMEM0	(NOMADIK_FSMC_BASE + 0x48)
+#define REG_FSMC_PATT0	(NOMADIK_FSMC_BASE + 0x4c)
+#define REG_FSMC_ECCR0	(NOMADIK_FSMC_BASE + 0x54)
+
+#endif /* __NOMADIK_H__ */
diff --git a/lib_arm/board.c b/lib_arm/board.c
index f125d38..09eaaf2 100644
--- a/lib_arm/board.c
+++ b/lib_arm/board.c
@@ -145,6 +145,9 @@ void inline yellow_LED_off(void)__attribute__((weak, alias("__yellow_LED_off")))
  * but let's get it working (again) first...
  */
 
+#if defined(CONFIG_ARM_DCC) && !defined(CONFIG_BAUDRATE)
+#define CONFIG_BAUDRATE 115200
+#endif
 static int init_baudrate (void)
 {
 	char tmp[64];	/* long enough for environment variables */