[PATCH] Add support for the AMCC Katmai (440SPe) eval board

Signed-off-by: Stefan Roese <sr@denx.de>

16 files changed, 1700 insertions, 19 deletions

diff --git a/MAINTAINERS b/MAINTAINERS
index f90c5a6..1d0a8df 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -288,6 +288,7 @@ Stefan Roese <sr@denx.de>
 	bamboo			PPC440EP
 	bunbinga		PPC405EP
 	ebony			PPC440GP
+	katmai			PPC440SPe
 	ocotea			PPC440GX
 	p3p440			PPC440GP
 	pcs440ep		PPC440EP
diff --git a/MAKEALL b/MAKEALL
index d943cee..c9f5958 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -81,15 +81,15 @@ LIST_4xx="	\
 	CRAYL1		csb272		csb472		DASA_SIM	\
 	DP405		DU405		ebony		ERIC		\
 	EXBITGEN	G2000		HH405		HUB405		\
-	JSE		KAREF		luan		METROBOX	\
-	MIP405		MIP405T		ML2		ml300		\
-	ocotea		OCRTC		ORSG		p3p440		\
-	PCI405		pcs440ep	PIP405		PLU405		\
-	PMC405		PPChameleonEVB	sbc405		sc3		\
-	sequoia		sequoia_nand	taishan		VOH405		\
-	VOM405		W7OLMC		W7OLMG		walnut		\
-	WUH405		XPEDITE1K	yellowstone	yosemite	\
-	yucca								\
+	JSE		KAREF		katmai		luan		\
+	METROBOX	MIP405		MIP405T		ML2		\
+	ml300		ocotea		OCRTC		ORSG		\
+	p3p440		PCI405		pcs440ep	PIP405		\
+	PLU405		PMC405		PPChameleonEVB	sbc405		\
+	sc3		sequoia		sequoia_nand	taishan		\
+	VOH405		VOM405		W7OLMC		W7OLMG		\
+	walnut		WUH405		XPEDITE1K	yellowstone	\
+	yosemite	yucca						\
 "
 
 #########################################################################
diff --git a/Makefile b/Makefile
index f39ff65..546a808 100644
--- a/Makefile
+++ b/Makefile
@@ -1092,6 +1092,9 @@ JSE_config:	unconfig
 KAREF_config: unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx karef sandburst
 
+katmai_config:	unconfig
+	@$(MKCONFIG) $(@:_config=) ppc ppc4xx katmai amcc
+
 luan_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx luan amcc
 
diff --git a/board/amcc/katmai/Makefile b/board/amcc/katmai/Makefile
new file mode 100644
index 0000000..d06a402
--- /dev/null
+++ b/board/amcc/katmai/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2007
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	= $(BOARD).o cmd_katmai.o
+SOBJS	= init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend *~
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/amcc/katmai/cmd_katmai.c b/board/amcc/katmai/cmd_katmai.c
new file mode 100644
index 0000000..684f6a5
--- /dev/null
+++ b/board/amcc/katmai/cmd_katmai.c
@@ -0,0 +1,267 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <asm/byteorder.h>
+
+static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	uchar	chip;
+	ulong	data;
+	int	nbytes;
+	extern char console_buffer[];
+
+	char sysClock[4];
+	char cpuClock[4];
+	char plbClock[4];
+	char pcixClock[4];
+
+	if (argc < 3) {
+		printf ("Usage:\n%s\n", cmdtp->usage);
+		return 1;
+	}
+
+	if (strcmp(argv[2], "prom0") == 0)
+		chip = IIC0_BOOTPROM_ADDR;
+	else
+		chip = IIC0_ALT_BOOTPROM_ADDR;
+
+	do {
+		printf("enter sys clock frequency 33 or 66 Mhz or quit to abort\n");
+		nbytes = readline (" ? ");
+
+		if (strcmp(console_buffer, "quit") == 0)
+			return 0;
+
+		if ((strcmp(console_buffer, "33") != 0) &
+		    (strcmp(console_buffer, "66") != 0))
+			nbytes=0;
+
+		strcpy(sysClock, console_buffer);
+
+	} while (nbytes == 0);
+
+	do {
+		if (strcmp(sysClock, "66") == 0) {
+			printf("enter cpu clock frequency 400, 533 Mhz or quit to abort\n");
+		} else {
+#ifdef	CONFIG_STRESS
+			printf("enter cpu clock frequency 400, 500, 533, 667 Mhz or quit to abort\n");
+#else
+			printf("enter cpu clock frequency 400, 500, 533 Mhz or quit to abort\n");
+#endif
+		}
+		nbytes = readline (" ? ");
+
+		if (strcmp(console_buffer, "quit") == 0)
+			return 0;
+
+		if (strcmp(sysClock, "66") == 0) {
+			if ((strcmp(console_buffer, "400") != 0) &
+			    (strcmp(console_buffer, "533") != 0)
+#ifdef	CONFIG_STRESS
+			    & (strcmp(console_buffer, "667") != 0)
+#endif
+				) {
+				nbytes = 0;
+			}
+		} else {
+			if ((strcmp(console_buffer, "400") != 0) &
+			    (strcmp(console_buffer, "500") != 0) &
+			    (strcmp(console_buffer, "533") != 0)
+#ifdef	CONFIG_STRESS
+			    & (strcmp(console_buffer, "667") != 0)
+#endif
+				) {
+				nbytes = 0;
+			}
+		}
+
+		strcpy(cpuClock, console_buffer);
+
+	} while (nbytes == 0);
+
+	if (strcmp(cpuClock, "500") == 0)
+		strcpy(plbClock, "166");
+	else if (strcmp(cpuClock, "533") == 0)
+		strcpy(plbClock, "133");
+	else {
+		do {
+			if (strcmp(cpuClock, "400") == 0)
+				printf("enter plb clock frequency 100, 133 Mhz or quit to abort\n");
+
+#ifdef	CONFIG_STRESS
+			if (strcmp(cpuClock, "667") == 0)
+				printf("enter plb clock frequency 133, 166 Mhz or quit to abort\n");
+
+#endif
+			nbytes = readline (" ? ");
+
+			if (strcmp(console_buffer, "quit") == 0)
+				return 0;
+
+			if (strcmp(cpuClock, "400") == 0) {
+				if ((strcmp(console_buffer, "100") != 0) &
+				    (strcmp(console_buffer, "133") != 0))
+					nbytes = 0;
+			}
+#ifdef	CONFIG_STRESS
+			if (strcmp(cpuClock, "667") == 0) {
+				if ((strcmp(console_buffer, "133") != 0) &
+				    (strcmp(console_buffer, "166") != 0))
+					nbytes = 0;
+			}
+#endif
+			strcpy(plbClock, console_buffer);
+
+		} while (nbytes == 0);
+	}
+
+	do {
+		printf("enter Pci-X clock frequency 33, 66, 100 or 133 Mhz or quit to abort\n");
+		nbytes = readline (" ? ");
+
+		if (strcmp(console_buffer, "quit") == 0)
+			return 0;
+
+		if ((strcmp(console_buffer, "33") != 0) &
+		    (strcmp(console_buffer, "66") != 0) &
+		    (strcmp(console_buffer, "100") != 0) &
+		    (strcmp(console_buffer, "133") != 0)) {
+			nbytes = 0;
+		}
+		strcpy(pcixClock, console_buffer);
+
+	} while (nbytes == 0);
+
+	printf("\nsys clk   = %sMhz\n", sysClock);
+	printf("cpu clk   = %sMhz\n", cpuClock);
+	printf("plb clk   = %sMhz\n", plbClock);
+	printf("Pci-X clk = %sMhz\n", pcixClock);
+
+	do {
+		printf("\npress [y] to write I2C bootstrap \n");
+		printf("or [n] to abort.  \n");
+		printf("Don't forget to set board switches \n");
+		printf("according to your choice before re-starting \n");
+		printf("(refer to 440spe_uboot_kit_um_1_01.pdf) \n");
+
+		nbytes = readline (" ? ");
+		if (strcmp(console_buffer, "n") == 0)
+			return 0;
+
+	} while (nbytes == 0);
+
+	if (strcmp(sysClock, "33") == 0) {
+		if ((strcmp(cpuClock, "400") == 0) &
+		    (strcmp(plbClock, "100") == 0))
+			data = 0x8678c206;
+
+		if ((strcmp(cpuClock, "400") == 0) &
+		    (strcmp(plbClock, "133") == 0))
+			data = 0x8678c2c6;
+
+		if ((strcmp(cpuClock, "500") == 0))
+			data = 0x8778f2c6;
+
+		if ((strcmp(cpuClock, "533") == 0))
+			data = 0x87790252;
+
+#ifdef	CONFIG_STRESS
+		if ((strcmp(cpuClock, "667") == 0) &
+		    (strcmp(plbClock, "133") == 0))
+			data = 0x87794256;
+
+		if ((strcmp(cpuClock, "667") == 0) &
+		    (strcmp(plbClock, "166") == 0))
+			data = 0x87794206;
+
+#endif
+	}
+	if (strcmp(sysClock, "66") == 0) {
+		if ((strcmp(cpuClock, "400") == 0) &
+		    (strcmp(plbClock, "100") == 0))
+			data = 0x84706206;
+
+		if ((strcmp(cpuClock, "400") == 0) &
+		    (strcmp(plbClock, "133") == 0))
+			data = 0x847062c6;
+
+		if ((strcmp(cpuClock, "533") == 0))
+			data = 0x85708206;
+
+#ifdef	CONFIG_STRESS
+		if ((strcmp(cpuClock, "667") == 0) &
+		    (strcmp(plbClock, "133") == 0))
+			data = 0x8570a256;
+
+		if ((strcmp(cpuClock, "667") == 0) &
+		    (strcmp(plbClock, "166") == 0))
+			data = 0x8570a206;
+
+#endif
+	}
+
+#ifdef	DEBUG
+	printf(" pin strap0 to write in i2c  = %x\n", data);
+#endif	/* DEBUG */
+
+	if (i2c_write(chip, 0, 1, (uchar *)&data, 4) != 0)
+		printf("Error writing strap0 in %s\n", argv[2]);
+
+	if (strcmp(pcixClock, "33") == 0)
+		data = 0x00000701;
+
+	if (strcmp(pcixClock, "66") == 0)
+		data = 0x00000601;
+
+	if (strcmp(pcixClock, "100") == 0)
+		data = 0x00000501;
+
+	if (strcmp(pcixClock, "133") == 0)
+		data = 0x00000401;
+
+	if (strcmp(plbClock, "166") == 0)
+		data |= 0x05950000;
+	else
+		data |= 0x05A50000;
+
+#ifdef	DEBUG
+	printf(" pin strap1 to write in i2c  = %x\n", data);
+#endif	/* DEBUG */
+
+	udelay(1000);
+	if (i2c_write(chip, 4, 1, (uchar *)&data, 4) != 0)
+		printf("Error writing strap1 in %s\n", argv[2]);
+
+	return 0;
+}
+
+U_BOOT_CMD(
+	bootstrap,	3,	1,	do_bootstrap,
+	"bootstrap - program the serial device strap\n",
+	"wrclk [prom0|prom1] - program the serial device strap\n"
+	);
diff --git a/board/amcc/katmai/config.mk b/board/amcc/katmai/config.mk
new file mode 100644
index 0000000..115c1ae
--- /dev/null
+++ b/board/amcc/katmai/config.mk
@@ -0,0 +1,38 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# AMCC 440SPe Evaluation (Katmai) board
+#
+
+TEXT_BASE = 0xfffc0000
+
+PLATFORM_CPPFLAGS += -DCONFIG_440=1
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
+
+ifeq ($(dbcr),1)
+PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
+endif
diff --git a/board/amcc/katmai/init.S b/board/amcc/katmai/init.S
new file mode 100644
index 0000000..f5900bc
--- /dev/null
+++ b/board/amcc/katmai/init.S
@@ -0,0 +1,108 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ *  Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <config.h>
+#include <asm-ppc/mmu.h>
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ *  Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+
+	.section .bootpg,"ax"
+
+/**************************************************************************
+ * TLB table for revA
+ *************************************************************************/
+	.globl tlbtabA
+tlbtabA:
+	tlbtab_start
+	tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_R|AC_W|AC_X|SA_G)
+
+	/*
+	 * TLB entries for SDRAM are not needed on this platform.
+	 * They are dynamically generated in the SPD DDR(2) detection
+	 * routine.
+	 */
+
+	tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I)
+	tlbentry(CFG_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_R|AC_W|SA_G|SA_I)
+
+	tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE_BASE, SZ_16K, 0x20000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+
+	tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x40000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x80000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0xC0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x50000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x90000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0xD0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbtab_end
+
+/**************************************************************************
+ * TLB table for revB
+ *
+ * Notice: revB of the 440SPe chip is very strict about PLB real addresses
+ * and ranges to be mapped for config space: it seems to only work with
+ * d_nnnn_nnnn range (hangs the core upon config transaction attempts when
+ * set otherwise) while revA uses c_nnnn_nnnn.
+ *************************************************************************/
+	.globl tlbtabB
+tlbtabB:
+	tlbtab_start
+	tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_R|AC_W|AC_X|SA_G)
+
+	/*
+	 * TLB entries for SDRAM are not needed on this platform.
+	 * They are dynamically generated in the SPD DDR(2) detection
+	 * routine.
+	 */
+
+	tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I)
+
+	tlbentry(CFG_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_R|AC_W|SA_G|SA_I)
+
+	tlbentry(CFG_ACE_BASE, SZ_1K, 0xE0000000, 4,AC_R|AC_W|SA_G|SA_I)
+
+	tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+
+	tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x00100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x20100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0x40100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x10000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x30000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0x50000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbtab_end
diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c
new file mode 100644
index 0000000..8704925
--- /dev/null
+++ b/board/amcc/katmai/katmai.c
@@ -0,0 +1,514 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+#include <i2c.h>
+#include <asm-ppc/io.h>
+
+#include "katmai.h"
+#include "../cpu/ppc4xx/440spe_pcie.h"
+
+#undef PCIE_ENDPOINT
+/* #define PCIE_ENDPOINT 1 */
+
+int ppc440spe_init_pcie_rootport(int port);
+void ppc440spe_setup_pcie(struct pci_controller *hose, int port);
+
+int board_early_init_f (void)
+{
+	unsigned long mfr;
+	unsigned long pfc;
+
+	/*----------------------------------------------------------------------+
+	 * Interrupt controller setup for the Katmai 440SPe Evaluation board.
+	 *-----------------------------------------------------------------------+
+	 *-----------------------------------------------------------------------+
+	 * Interrupt | Source                            | Pol.  | Sensi.| Crit. |
+	 *-----------+-----------------------------------+-------+-------+-------+
+	 * IRQ 00    | UART0                             | High  | Level | Non   |
+	 * IRQ 01    | UART1                             | High  | Level | Non   |
+	 * IRQ 02    | IIC0                              | High  | Level | Non   |
+	 * IRQ 03    | IIC1                              | High  | Level | Non   |
+	 * IRQ 04    | PCI0X0 MSG IN                     | High  | Level | Non   |
+	 * IRQ 05    | PCI0X0 CMD Write                  | High  | Level | Non   |
+	 * IRQ 06    | PCI0X0 Power Mgt                  | High  | Level | Non   |
+	 * IRQ 07    | PCI0X0 VPD Access                 | Rising| Edge  | Non   |
+	 * IRQ 08    | PCI0X0 MSI level 0                | High  | Lvl/ed| Non   |
+	 * IRQ 09    | External IRQ 15 - (PCI-Express)   | pgm H | Pgm   | Non   |
+	 * IRQ 10    | UIC2 Non-critical Int.            | NA    | NA    | Non   |
+	 * IRQ 11    | UIC2 Critical Interrupt           | NA    | NA    | Crit  |
+	 * IRQ 12    | PCI Express MSI Level 0           | Rising| Edge  | Non   |
+	 * IRQ 13    | PCI Express MSI Level 1           | Rising| Edge  | Non   |
+	 * IRQ 14    | PCI Express MSI Level 2           | Rising| Edge  | Non   |
+	 * IRQ 15    | PCI Express MSI Level 3           | Rising| Edge  | Non   |
+	 * IRQ 16    | UIC3 Non-critical Int.            | NA    | NA    | Non   |
+	 * IRQ 17    | UIC3 Critical Interrupt           | NA    | NA    | Crit  |
+	 * IRQ 18    | External IRQ 14 - (PCI-Express)   | Pgm   | Pgm   | Non   |
+	 * IRQ 19    | DMA Channel 0 FIFO Full           | High  | Level | Non   |
+	 * IRQ 20    | DMA Channel 0 Stat FIFO           | High  | Level | Non   |
+	 * IRQ 21    | DMA Channel 1 FIFO Full           | High  | Level | Non   |
+	 * IRQ 22    | DMA Channel 1 Stat FIFO           | High  | Level | Non   |
+	 * IRQ 23    | I2O Inbound Doorbell              | High  | Level | Non   |
+	 * IRQ 24    | Inbound Post List FIFO Not Empt   | High  | Level | Non   |
+	 * IRQ 25    | I2O Region 0 LL PLB Write         | High  | Level | Non   |
+	 * IRQ 26    | I2O Region 1 LL PLB Write         | High  | Level | Non   |
+	 * IRQ 27    | I2O Region 0 HB PLB Write         | High  | Level | Non   |
+	 * IRQ 28    | I2O Region 1 HB PLB Write         | High  | Level | Non   |
+	 * IRQ 29    | GPT Down Count Timer              | Rising| Edge  | Non   |
+	 * IRQ 30    | UIC1 Non-critical Int.            | NA    | NA    | Non   |
+	 * IRQ 31    | UIC1 Critical Interrupt           | NA    | NA    | Crit. |
+	 *------------------------------------------------------------------------
+	 * IRQ 32    | Ext. IRQ 13 - (PCI-Express)       |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 33    | MAL Serr                          | High  | Level | Non   |
+	 * IRQ 34    | MAL Txde                          | High  | Level | Non   |
+	 * IRQ 35    | MAL Rxde                          | High  | Level | Non   |
+	 * IRQ 36    | DMC CE or DMC UE                  | High  | Level | Non   |
+	 * IRQ 37    | EBC or UART2                      | High  |Lvl Edg| Non   |
+	 * IRQ 38    | MAL TX EOB                        | High  | Level | Non   |
+	 * IRQ 39    | MAL RX EOB                        | High  | Level | Non   |
+	 * IRQ 40    | PCIX0 MSI Level 1                 | High  |Lvl Edg| Non   |
+	 * IRQ 41    | PCIX0 MSI level 2                 | High  |Lvl Edg| Non   |
+	 * IRQ 42    | PCIX0 MSI level 3                 | High  |Lvl Edg| Non   |
+	 * IRQ 43    | L2 Cache                          | Risin | Edge  | Non   |
+	 * IRQ 44    | GPT Compare Timer 0               | Risin | Edge  | Non   |
+	 * IRQ 45    | GPT Compare Timer 1               | Risin | Edge  | Non   |
+	 * IRQ 46    | GPT Compare Timer 2               | Risin | Edge  | Non   |
+	 * IRQ 47    | GPT Compare Timer 3               | Risin | Edge  | Non   |
+	 * IRQ 48    | GPT Compare Timer 4               | Risin | Edge  | Non   |
+	 * IRQ 49    | Ext. IRQ 12 - PCI-X               |pgm/Fal|pgm/Lvl| Non   |
+	 * IRQ 50    | Ext. IRQ 11 -                     |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 51    | Ext. IRQ 10 -                     |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 52    | Ext. IRQ 9                        |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 53    | Ext. IRQ 8                        |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 54    | DMA Error                         | High  | Level | Non   |
+	 * IRQ 55    | DMA I2O Error                     | High  | Level | Non   |
+	 * IRQ 56    | Serial ROM                        | High  | Level | Non   |
+	 * IRQ 57    | PCIX0 Error                       | High  | Edge  | Non   |
+	 * IRQ 58    | Ext. IRQ 7-                       |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 59    | Ext. IRQ 6-                       |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 60    | EMAC0 Interrupt                   | High  | Level | Non   |
+	 * IRQ 61    | EMAC0 Wake-up                     | High  | Level | Non   |
+	 * IRQ 62    | Reserved                          | High  | Level | Non   |
+	 * IRQ 63    | XOR                               | High  | Level | Non   |
+	 *-----------------------------------------------------------------------
+	 * IRQ 64    | PE0 AL                            | High  | Level | Non   |
+	 * IRQ 65    | PE0 VPD Access                    | Risin | Edge  | Non   |
+	 * IRQ 66    | PE0 Hot Reset Request             | Risin | Edge  | Non   |
+	 * IRQ 67    | PE0 Hot Reset Request             | Falli | Edge  | Non   |
+	 * IRQ 68    | PE0 TCR                           | High  | Level | Non   |
+	 * IRQ 69    | PE0 BusMaster VCO                 | Falli | Edge  | Non   |
+	 * IRQ 70    | PE0 DCR Error                     | High  | Level | Non   |
+	 * IRQ 71    | Reserved                          | N/A   | N/A   | Non   |
+	 * IRQ 72    | PE1 AL                            | High  | Level | Non   |
+	 * IRQ 73    | PE1 VPD Access                    | Risin | Edge  | Non   |
+	 * IRQ 74    | PE1 Hot Reset Request             | Risin | Edge  | Non   |
+	 * IRQ 75    | PE1 Hot Reset Request             | Falli | Edge  | Non   |
+	 * IRQ 76    | PE1 TCR                           | High  | Level | Non   |
+	 * IRQ 77    | PE1 BusMaster VCO                 | Falli | Edge  | Non   |
+	 * IRQ 78    | PE1 DCR Error                     | High  | Level | Non   |
+	 * IRQ 79    | Reserved                          | N/A   | N/A   | Non   |
+	 * IRQ 80    | PE2 AL                            | High  | Level | Non   |
+	 * IRQ 81    | PE2 VPD Access                    | Risin | Edge  | Non   |
+	 * IRQ 82    | PE2 Hot Reset Request             | Risin | Edge  | Non   |
+	 * IRQ 83    | PE2 Hot Reset Request             | Falli | Edge  | Non   |
+	 * IRQ 84    | PE2 TCR                           | High  | Level | Non   |
+	 * IRQ 85    | PE2 BusMaster VCO                 | Falli | Edge  | Non   |
+	 * IRQ 86    | PE2 DCR Error                     | High  | Level | Non   |
+	 * IRQ 87    | Reserved                          | N/A   | N/A   | Non   |
+	 * IRQ 88    | External IRQ(5)                   | Progr | Progr | Non   |
+	 * IRQ 89    | External IRQ 4 - Ethernet         | Progr | Progr | Non   |
+	 * IRQ 90    | External IRQ 3 - PCI-X            | Progr | Progr | Non   |
+	 * IRQ 91    | External IRQ 2 - PCI-X            | Progr | Progr | Non   |
+	 * IRQ 92    | External IRQ 1 - PCI-X            | Progr | Progr | Non   |
+	 * IRQ 93    | External IRQ 0 - PCI-X            | Progr | Progr | Non   |
+	 * IRQ 94    | Reserved                          | N/A   | N/A   | Non   |
+	 * IRQ 95    | Reserved                          | N/A   | N/A   | Non   |
+	 *-----------------------------------------------------------------------
+	 * IRQ 96    | PE0 INTA                          | High  | Level | Non   |
+	 * IRQ 97    | PE0 INTB                          | High  | Level | Non   |
+	 * IRQ 98    | PE0 INTC                          | High  | Level | Non   |
+	 * IRQ 99    | PE0 INTD                          | High  | Level | Non   |
+	 * IRQ 100   | PE1 INTA                          | High  | Level | Non   |
+	 * IRQ 101   | PE1 INTB                          | High  | Level | Non   |
+	 * IRQ 102   | PE1 INTC                          | High  | Level | Non   |
+	 * IRQ 103   | PE1 INTD                          | High  | Level | Non   |
+	 * IRQ 104   | PE2 INTA                          | High  | Level | Non   |
+	 * IRQ 105   | PE2 INTB                          | High  | Level | Non   |
+	 * IRQ 106   | PE2 INTC                          | High  | Level | Non   |
+	 * IRQ 107   | PE2 INTD                          | Risin | Edge  | Non   |
+	 * IRQ 108   | PCI Express MSI Level 4           | Risin | Edge  | Non   |
+	 * IRQ 109   | PCI Express MSI Level 5           | Risin | Edge  | Non   |
+	 * IRQ 110   | PCI Express MSI Level 6           | Risin | Edge  | Non   |
+	 * IRQ 111   | PCI Express MSI Level 7           | Risin | Edge  | Non   |
+	 * IRQ 116   | PCI Express MSI Level 12          | Risin | Edge  | Non   |
+	 * IRQ 112   | PCI Express MSI Level 8           | Risin | Edge  | Non   |
+	 * IRQ 113   | PCI Express MSI Level 9           | Risin | Edge  | Non   |
+	 * IRQ 114   | PCI Express MSI Level 10          | Risin | Edge  | Non   |
+	 * IRQ 115   | PCI Express MSI Level 11          | Risin | Edge  | Non   |
+	 * IRQ 117   | PCI Express MSI Level 13          | Risin | Edge  | Non   |
+	 * IRQ 118   | PCI Express MSI Level 14          | Risin | Edge  | Non   |
+	 * IRQ 119   | PCI Express MSI Level 15          | Risin | Edge  | Non   |
+	 * IRQ 120   | PCI Express MSI Level 16          | Risin | Edge  | Non   |
+	 * IRQ 121   | PCI Express MSI Level 17          | Risin | Edge  | Non   |
+	 * IRQ 122   | PCI Express MSI Level 18          | Risin | Edge  | Non   |
+	 * IRQ 123   | PCI Express MSI Level 19          | Risin | Edge  | Non   |
+	 * IRQ 124   | PCI Express MSI Level 20          | Risin | Edge  | Non   |
+	 * IRQ 125   | PCI Express MSI Level 21          | Risin | Edge  | Non   |
+	 * IRQ 126   | PCI Express MSI Level 22          | Risin | Edge  | Non   |
+	 * IRQ 127   | PCI Express MSI Level 23          | Risin | Edge  | Non   |
+	 *-----------+-----------------------------------+-------+-------+-------+ */
+	/*-------------------------------------------------------------------------+
+	 * Put UICs in PowerPC440SPemode.
+	 * Initialise UIC registers.  Clear all interrupts.  Disable all interrupts.
+	 * Set critical interrupt values.  Set interrupt polarities.  Set interrupt
+	 * trigger levels.  Make bit 0 High  priority.  Clear all interrupts again.
+	 *------------------------------------------------------------------------*/
+	mtdcr (uic3sr, 0xffffffff);	/* Clear all interrupts */
+	mtdcr (uic3er, 0x00000000);	/* disable all interrupts */
+	mtdcr (uic3cr, 0x00000000);	/* Set Critical / Non Critical interrupts: */
+	mtdcr (uic3pr, 0xffffffff);	/* Set Interrupt Polarities*/
+	mtdcr (uic3tr, 0x001fffff);	/* Set Interrupt Trigger Levels */
+	mtdcr (uic3vr, 0x00000001);	/* Set Vect base=0,INT31 Highest priority */
+	mtdcr (uic3sr, 0x00000000);	/* clear all  interrupts*/
+	mtdcr (uic3sr, 0xffffffff);	/* clear all  interrupts*/
+
+
+	mtdcr (uic2sr, 0xffffffff);	/* Clear all interrupts */
+	mtdcr (uic2er, 0x00000000);	/* disable all interrupts*/
+	mtdcr (uic2cr, 0x00000000);	/* Set Critical / Non Critical interrupts*/
+	mtdcr (uic2pr, 0xebebebff);	/* Set Interrupt Polarities*/
+	mtdcr (uic2tr, 0x74747400);	/* Set Interrupt Trigger Levels */
+	mtdcr (uic2vr, 0x00000001);	/* Set Vect base=0,INT31 Highest priority */
+	mtdcr (uic2sr, 0x00000000);	/* clear all interrupts */
+	mtdcr (uic2sr, 0xffffffff);	/* clear all interrupts */
+
+	mtdcr (uic1sr, 0xffffffff);	/* Clear all interrupts*/
+	mtdcr (uic1er, 0x00000000);	/* disable all interrupts*/
+	mtdcr (uic1cr, 0x00000000);	/* Set Critical / Non Critical interrupts*/
+	mtdcr (uic1pr, 0xffffffff);	/* Set Interrupt Polarities */
+	mtdcr (uic1tr, 0x001f8040);	/* Set Interrupt Trigger Levels*/
+	mtdcr (uic1vr, 0x00000001);	/* Set Vect base=0,INT31 Highest priority */
+	mtdcr (uic1sr, 0x00000000);	/* clear all interrupts*/
+	mtdcr (uic1sr, 0xffffffff);	/* clear all interrupts*/
+
+	mtdcr (uic0sr, 0xffffffff);	/* Clear all interrupts */
+	mtdcr (uic0er, 0x00000000);	/* disable all interrupts excepted cascade    to be checked */
+	mtdcr (uic0cr, 0x00104001);	/* Set Critical / Non Critical interrupts*/
+	mtdcr (uic0pr, 0xffffffff);	/* Set Interrupt Polarities*/
+	mtdcr (uic0tr, 0x010f0004);	/* Set Interrupt Trigger Levels */
+	mtdcr (uic0vr, 0x00000001);	/* Set Vect base=0,INT31 Highest priority */
+	mtdcr (uic0sr, 0x00000000);	/* clear all interrupts*/
+	mtdcr (uic0sr, 0xffffffff);	/* clear all interrupts*/
+
+/* SDR0_MFR should be part of Ethernet init */
+	mfsdr (sdr_mfr, mfr);
+	mfr &= ~SDR0_MFR_ECS_MASK;
+/*	mtsdr(sdr_mfr, mfr); */
+
+	/*
+	 * Setup GPIO signalling per defines in katmai.h
+	 */
+	pfc = PFC0_KATMAI;
+	mtsdr(SDR0_PFC0, pfc);
+
+	out32(GPIO0_OR_ADDR, GPIO_OR_KATMAI);
+	out32(GPIO0_ODR_ADDR, GPIO_ODR_KATMAI);
+	out32(GPIO0_TCR_ADDR, GPIO_TCR_KATMAI);
+
+	return 0;
+}
+
+int checkboard (void)
+{
+	char *s = getenv("serial#");
+
+	printf("Board: Katmai - AMCC 440SPe Evaluation Board");
+	if (s != NULL) {
+		puts(", serial# ");
+		puts(s);
+	}
+	putc('\n');
+
+	return 0;
+}
+
+#if defined(CFG_DRAM_TEST)
+int testdram (void)
+{
+	uint *pstart = (uint *) 0x00000000;
+	uint *pend = (uint *) 0x08000000;
+	uint *p;
+
+	for (p = pstart; p < pend; p++)
+		*p = 0xaaaaaaaa;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0xaaaaaaaa) {
+			printf ("SDRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	for (p = pstart; p < pend; p++)
+		*p = 0x55555555;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0x55555555) {
+			printf ("SDRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+	return 0;
+}
+#endif
+
+/*************************************************************************
+ *  pci_pre_init
+ *
+ *  This routine is called just prior to registering the hose and gives
+ *  the board the opportunity to check things. Returning a value of zero
+ *  indicates that things are bad & PCI initialization should be aborted.
+ *
+ *	Different boards may wish to customize the pci controller structure
+ *	(add regions, override default access routines, etc) or perform
+ *	certain pre-initialization actions.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+int pci_pre_init(struct pci_controller * hose )
+{
+	unsigned long strap;
+
+	/*-------------------------------------------------------------------+
+	 *	The katmai board is always configured as the host & requires the
+	 *	PCI arbiter to be enabled.
+	 *-------------------------------------------------------------------*/
+	mfsdr(sdr_sdstp1, strap);
+	if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
+		printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
+		return 0;
+	}
+
+	return 1;
+}
+#endif	/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+
+/*************************************************************************
+ *  pci_target_init
+ *
+ *	The bootstrap configuration provides default settings for the pci
+ *	inbound map (PIM). But the bootstrap config choices are limited and
+ *	may not be sufficient for a given board.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+void pci_target_init(struct pci_controller * hose )
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/*-------------------------------------------------------------------+
+	 * Disable everything
+	 *-------------------------------------------------------------------*/
+	out32r( PCIX0_PIM0SA, 0 ); /* disable */
+	out32r( PCIX0_PIM1SA, 0 ); /* disable */
+	out32r( PCIX0_PIM2SA, 0 ); /* disable */
+	out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+
+	/*-------------------------------------------------------------------+
+	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
+	 * strapping options to not support sizes such as 128/256 MB.
+	 *-------------------------------------------------------------------*/
+	out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE );
+	out32r( PCIX0_PIM0LAH, 0 );
+	out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+	out32r( PCIX0_BAR0, 0 );
+
+	/*-------------------------------------------------------------------+
+	 * Program the board's subsystem id/vendor id
+	 *-------------------------------------------------------------------*/
+	out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
+	out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID );
+
+	out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
+}
+#endif	/* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+
+#if defined(CONFIG_PCI)
+/*************************************************************************
+ *  is_pci_host
+ *
+ *	This routine is called to determine if a pci scan should be
+ *	performed. With various hardware environments (especially cPCI and
+ *	PPMC) it's insufficient to depend on the state of the arbiter enable
+ *	bit in the strap register, or generic host/adapter assumptions.
+ *
+ *	Rather than hard-code a bad assumption in the general 440 code, the
+ *	440 pci code requires the board to decide at runtime.
+ *
+ *	Return 0 for adapter mode, non-zero for host (monarch) mode.
+ *
+ *
+ ************************************************************************/
+int is_pci_host(struct pci_controller *hose)
+{
+	/* The katmai board is always configured as host. */
+	return 1;
+}
+
+static struct pci_controller pcie_hose[3] = {{0},{0},{0}};
+
+void pcie_setup_hoses(void)
+{
+	struct pci_controller *hose;
+	int i, bus;
+
+	/*
+	 * assume we're called after the PCIX hose is initialized, which takes
+	 * bus ID 0 and therefore start numbering PCIe's from 1.
+	 */
+	bus = 1;
+	for (i = 0; i <= 2; i++) {
+#ifdef PCIE_ENDPOINT
+ 		if (ppc440spe_init_pcie_endport(i)) {
+#else
+		if (ppc440spe_init_pcie_rootport(i)) {
+#endif
+			printf("PCIE%d: initialization failed\n", i);
+			continue;
+		}
+
+		hose = &pcie_hose[i];
+		hose->first_busno = bus;
+		hose->last_busno  = bus;
+		bus++;
+
+		/* setup mem resource */
+		pci_set_region(hose->regions + 0,
+			       CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
+			       CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
+			       CFG_PCIE_MEMSIZE,
+			       PCI_REGION_MEM
+			);
+		hose->region_count = 1;
+		pci_register_hose(hose);
+
+#ifdef PCIE_ENDPOINT
+		ppc440spe_setup_pcie_endpoint(hose, i);
+		/*
+		 * Reson for no scanning is endpoint can not generate
+		 * upstream configuration accesses.
+		 */
+#else
+		ppc440spe_setup_pcie_rootpoint(hose, i);
+		/*
+		 * Config access can only go down stream
+		 */
+		hose->last_busno = pci_hose_scan(hose);
+#endif
+	}
+}
+#endif	/* defined(CONFIG_PCI) */
+
+int misc_init_f (void)
+{
+	uint reg;
+#if defined(CONFIG_STRESS)
+	uint i ;
+	uint disp;
+#endif
+
+	/* minimal init for PCIe */
+#if 0 /* test-only: test endpoint at some time, for now rootpoint only */
+	/* pci express 0 Endpoint Mode */
+	mfsdr(SDR0_PE0DLPSET, reg);
+	reg &= (~0x00400000);
+	mtsdr(SDR0_PE0DLPSET, reg);
+#else
+	/* pci express 0 Rootpoint  Mode */
+	mfsdr(SDR0_PE0DLPSET, reg);
+	reg |= 0x00400000;
+	mtsdr(SDR0_PE0DLPSET, reg);
+#endif
+	/* pci express 1 Rootpoint  Mode */
+	mfsdr(SDR0_PE1DLPSET, reg);
+	reg |= 0x00400000;
+	mtsdr(SDR0_PE1DLPSET, reg);
+	/* pci express 2 Rootpoint  Mode */
+	mfsdr(SDR0_PE2DLPSET, reg);
+	reg |= 0x00400000;
+	mtsdr(SDR0_PE2DLPSET, reg);
+
+#if defined(CONFIG_STRESS)
+	/*
+	 * All this setting done by linux only needed by stress an charac. test
+	 * procedure
+	 * PCIe 1 Rootpoint PCIe2 Endpoint
+	 * PCIe 0 FIR Pre-emphasis Filter Coefficients & Transmit Driver Power Level
+	 */
+	for (i=0,disp=0; i<8; i++,disp+=3) {
+		mfsdr(SDR0_PE0HSSSET1L0+disp, reg);
+		reg |= 0x33000000;
+		mtsdr(SDR0_PE0HSSSET1L0+disp, reg);
+	}
+
+	/*PCIe 1 FIR Pre-emphasis Filter Coefficients & Transmit Driver Power Level */
+	for (i=0,disp=0; i<4; i++,disp+=3) {
+		mfsdr(SDR0_PE1HSSSET1L0+disp, reg);
+		reg |= 0x33000000;
+		mtsdr(SDR0_PE1HSSSET1L0+disp, reg);
+	}
+
+	/*PCIE 2 FIR Pre-emphasis Filter Coefficients & Transmit Driver Power Level */
+	for (i=0,disp=0; i<4; i++,disp+=3) {
+		mfsdr(SDR0_PE2HSSSET1L0+disp, reg);
+		reg |= 0x33000000;
+		mtsdr(SDR0_PE2HSSSET1L0+disp, reg);
+	}
+
+	reg = 0x21242222;
+	mtsdr(SDR0_PE2UTLSET1, reg);
+	reg = 0x11000000;
+	mtsdr(SDR0_PE2UTLSET2, reg);
+	/* pci express 1 Endpoint  Mode */
+	reg = 0x00004000;
+	mtsdr(SDR0_PE2DLPSET, reg);
+
+	mtsdr(SDR0_UART1, 0x2080005a);	/* patch for TG */
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_POST
+/*
+ * Returns 1 if keys pressed to start the power-on long-running tests
+ * Called from board_init_f().
+ */
+int post_hotkeys_pressed(void)
+{
+	return (ctrlc());
+}
+#endif
diff --git a/board/amcc/katmai/katmai.h b/board/amcc/katmai/katmai.h
new file mode 100644
index 0000000..9d5b793
--- /dev/null
+++ b/board/amcc/katmai/katmai.h
@@ -0,0 +1,65 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __KATMAI_H_
+#define __KATMAI_H_
+
+/*----------------------------------------------------------------------------
+ *                    XX
+ *   XXXX    XX XXX   XXX     XXXX
+ * XX        XX  XX   XX    XX  XX
+ * XX  XXX   XX  XX   XX    XX  XX
+ * XX  XX    XXXXX    XX    XX  XX
+ *  XXXX     XX      XXXX    XXXX
+ *          XXXX
+ *
+ *  The 440SPe provices 32 bits of GPIO.  By default all GPIO pins
+ *  are disabled, and must be explicitly enabled by setting a
+ *  bit in the SDR0_PFC0 indirect DCR.  Each GPIO maps 1-to-1 with the
+ *  corresponding bit in the SDR0_PFC0 register (note that bit numbers
+ *  reflect the PowerPC convention where bit 0 is the most-significant
+ *  bit).
+ *
+ *   Katmai specific:
+ *      RS232_RX_EN# is held HIGH during reset by hardware, keeping the
+ *      RS232_CTS, DSR & DCD  signals coming from the MAX3411 (U26) in
+ *      Hi-Z condition. This prevents contention between the MAX3411 (U26)
+ *      and 74CBTLV3125PG (U2) during reset.
+ *
+ *      RS232_RX_EN# is connected as GPIO pin 30.  Once the processor
+ *      is released from reset, this pin must be configured as an output and
+ *      then driven high to enable the receive signals from the UART transciever.
+ *----------------------------------------------------------------------------*/
+#define GPIO_ENABLE(gpio)       (0x80000000 >> (gpio))
+
+#define PFC0_KATMAI             GPIO_ENABLE(30)
+#define GPIO_OR_KATMAI          GPIO_ENABLE(30)     /* Drive all outputs low except GPIO 30 */
+#define GPIO_TCR_KATMAI         GPIO_ENABLE(30)
+#define GPIO_ODR_KATMAI         0                   /* Disable open drain for all outputs */
+
+#define GPIO0_OR_ADDR           (CFG_PERIPHERAL_BASE + 0x700)
+#define GPIO0_TCR_ADDR          (CFG_PERIPHERAL_BASE + 0x704)
+#define GPIO0_ODR_ADDR          (CFG_PERIPHERAL_BASE + 0x718)
+#define GPIO0_IR_ADDR           (CFG_PERIPHERAL_BASE + 0x71C)
+
+#endif /* __KATMAI_H_ */
diff --git a/board/amcc/katmai/u-boot.lds b/board/amcc/katmai/u-boot.lds
new file mode 100644
index 0000000..9fe661e
--- /dev/null
+++ b/board/amcc/katmai/u-boot.lds
@@ -0,0 +1,157 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/ppc4xx/start.o	(.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text)	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data)	}
+  .rel.rodata    : { *(.rel.rodata)	}
+  .rela.rodata   : { *(.rela.rodata)	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o		(.text)
+    board/amcc/katmai/init.o	(.text)
+    cpu/ppc4xx/kgdb.o		(.text)
+    cpu/ppc4xx/traps.o		(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o		(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o		(.text)
+    common/dlmalloc.o		(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o		(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/cpu/ppc4xx/cpu_init.c b/cpu/ppc4xx/cpu_init.c
index ae24591..82ae443 100644
--- a/cpu/ppc4xx/cpu_init.c
+++ b/cpu/ppc4xx/cpu_init.c
@@ -314,7 +314,7 @@ cpu_init_f (void)
 #endif
 
 #if defined (CFG_EBC_CFG)
-	mtebc(epcr, CFG_EBC_CFG);
+	mtebc(EBC0_CFG, CFG_EBC_CFG);
 #endif
 
 #if defined(CONFIG_WATCHDOG)
diff --git a/cpu/ppc4xx/speed.c b/cpu/ppc4xx/speed.c
index 2d16a83..06220c3 100644
--- a/cpu/ppc4xx/speed.c
+++ b/cpu/ppc4xx/speed.c
@@ -331,7 +331,7 @@ void get_sys_info (sys_info_t * sysInfo)
 	unsigned long m;
 	unsigned long prbdv0;
 
-#if defined(CONFIG_440SPE)
+#if defined(CONFIG_YUCCA)
 	unsigned long sys_freq;
 	unsigned long sys_per=0;
 	unsigned long msr;
@@ -348,7 +348,7 @@ void get_sys_info (sys_info_t * sysInfo)
 	/*-------------------------------------------------------------------------+
 	 | Calculate the system clock speed from the period.
 	 +-------------------------------------------------------------------------*/
-	sys_freq=(ONE_BILLION/sys_per)*1000;
+	sys_freq = (ONE_BILLION / sys_per) * 1000;
 #endif
 
 	/* Extract configured divisors */
@@ -385,17 +385,17 @@ void get_sys_info (sys_info_t * sysInfo)
 		m = sysInfo->pllExtBusDiv * sysInfo->pllOpbDiv * sysInfo->pllFwdDivB;
 
 	/* Now calculate the individual clocks */
-#if defined(CONFIG_440SPE)
+#if defined(CONFIG_YUCCA)
 	sysInfo->freqVCOMhz = (m * sys_freq) ;
 #else
-	sysInfo->freqVCOMhz = (m * CONFIG_SYS_CLK_FREQ) + (m>>1);
+	sysInfo->freqVCOMhz = (m * CONFIG_SYS_CLK_FREQ) + (m >> 1);
 #endif
 	sysInfo->freqProcessor = sysInfo->freqVCOMhz/sysInfo->pllFwdDivA;
 	sysInfo->freqPLB = sysInfo->freqVCOMhz/sysInfo->pllFwdDivB/prbdv0;
 	sysInfo->freqOPB = sysInfo->freqPLB/sysInfo->pllOpbDiv;
 	sysInfo->freqEPB = sysInfo->freqOPB/sysInfo->pllExtBusDiv;
 
-#if defined(CONFIG_440SPE)
+#if defined(CONFIG_YUCCA)
 	/* Determine PCI Clock Period */
 	pci_clock_per = determine_pci_clock_per();
 	sysInfo->freqPCI = (ONE_BILLION/pci_clock_per) * 1000;
@@ -408,7 +408,7 @@ void get_sys_info (sys_info_t * sysInfo)
 
 #endif
 
-#if defined(CONFIG_440SPE)
+#if defined(CONFIG_YUCCA)
 unsigned long determine_sysper(void)
 {
 	unsigned int fpga_clocking_reg;
@@ -583,7 +583,6 @@ unsigned long determine_sysper(void)
 	}
 
 	return(sys_per);
-
 }
 
 /*-------------------------------------------------------------------------+
diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S
index 8e000d3..a3db93f 100644
--- a/cpu/ppc4xx/start.S
+++ b/cpu/ppc4xx/start.S
@@ -1856,3 +1856,60 @@ pll_wait:
 				     /* execution will continue from the poweron */
 				     /* vector of 0xfffffffc */
 #endif /* CONFIG_405EP */
+
+#if defined(CONFIG_440)
+#define function_prolog(func_name)      .text; \
+                                        .align 2; \
+                                        .globl func_name; \
+                                        func_name:
+#define function_epilog(func_name)      .type func_name,@function; \
+                                        .size func_name,.-func_name
+
+/*----------------------------------------------------------------------------+
+| mttlb3.
++----------------------------------------------------------------------------*/
+	function_prolog(mttlb3)
+	TLBWE(4,3,2)
+	blr
+	function_epilog(mttlb3)
+
+/*----------------------------------------------------------------------------+
+| mftlb3.
++----------------------------------------------------------------------------*/
+	function_prolog(mftlb3)
+        TLBRE(3,3,2)
+	blr
+	function_epilog(mftlb3)
+
+/*----------------------------------------------------------------------------+
+| mttlb2.
++----------------------------------------------------------------------------*/
+	function_prolog(mttlb2)
+	TLBWE(4,3,1)
+	blr
+	function_epilog(mttlb2)
+
+/*----------------------------------------------------------------------------+
+| mftlb2.
++----------------------------------------------------------------------------*/
+	function_prolog(mftlb2)
+        TLBRE(3,3,1)
+	blr
+	function_epilog(mftlb2)
+
+/*----------------------------------------------------------------------------+
+| mttlb1.
++----------------------------------------------------------------------------*/
+	function_prolog(mttlb1)
+	TLBWE(4,3,0)
+	blr
+	function_epilog(mttlb1)
+
+/*----------------------------------------------------------------------------+
+| mftlb1.
++----------------------------------------------------------------------------*/
+	function_prolog(mftlb1)
+        TLBRE(3,3,0)
+	blr
+	function_epilog(mftlb1)
+#endif /* CONFIG_440 */
diff --git a/include/configs/katmai.h b/include/configs/katmai.h
new file mode 100644
index 0000000..c750e14
--- /dev/null
+++ b/include/configs/katmai.h
@@ -0,0 +1,415 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * katmai.h - configuration for AMCC Katmai (440SPe)
+ ***********************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_KATMAI			1	/* Board is Katmai	*/
+#define CONFIG_4xx			1	/* ... PPC4xx family	*/
+#define CONFIG_440			1	/* ... PPC440 family	*/
+#define CONFIG_440SPE			1	/* Specifc SPe support	*/
+#undef	CFG_DRAM_TEST				/* Disable-takes long time */
+#define CONFIG_SYS_CLK_FREQ	33333333	/* external freq to pll	*/
+
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_pre_init		*/
+#define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
+#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
+#undef  CONFIG_SHOW_BOOT_PROGRESS
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(512 * 1024)	/* Reserve 512 kB for malloc */
+
+#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
+#define CFG_FLASH_BASE		0xff000000	/* start of FLASH	*/
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_PERIPHERAL_BASE	0xa0000000	/* internal peripherals	*/
+#define CFG_ISRAM_BASE		0x90000000	/* internal SRAM	*/
+
+#define CFG_PCI_MEMBASE		0x80000000	/* mapped PCI memory	*/
+#define CFG_PCI_BASE		0xd0000000	/* internal PCI regs	*/
+#define CFG_PCI_TARGBASE	CFG_PCI_MEMBASE
+
+#define CFG_PCIE_MEMBASE	0xb0000000	/* mapped PCIe memory	*/
+#define CFG_PCIE_MEMSIZE	0x01000000
+#define CFG_PCIE_BASE		0xe0000000	/* PCIe UTL regs */
+
+#define CFG_PCIE0_CFGBASE	0xc0000000
+#define CFG_PCIE0_XCFGBASE	0xc0000400
+#define CFG_PCIE1_CFGBASE	0xc0001000
+#define CFG_PCIE1_XCFGBASE	0xc0001400
+#define CFG_PCIE2_CFGBASE	0xc0002000
+#define CFG_PCIE2_XCFGBASE	0xc0002400
+
+/* System RAM mapped to PCI space */
+#define CONFIG_PCI_SYS_MEM_BUS	CFG_SDRAM_BASE
+#define CONFIG_PCI_SYS_MEM_PHYS	CFG_SDRAM_BASE
+#define CONFIG_PCI_SYS_MEM_SIZE	(1024 * 1024 * 1024)
+
+#define CFG_ACE_BASE		0xe0000000	/* Xilinx ACE controller - Compact Flash */
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in internal SRAM)
+ *----------------------------------------------------------------------*/
+#define CFG_TEMP_STACK_OCM	1
+#define CFG_OCM_DATA_ADDR	CFG_ISRAM_BASE
+#define CFG_INIT_RAM_ADDR	CFG_ISRAM_BASE	/* Initial RAM address	*/
+#define CFG_INIT_RAM_END	0x2000		/* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data */
+
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
+#define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CONFIG_SERIAL_MULTI	1
+#undef CONFIG_UART1_CONSOLE
+#undef CFG_EXT_SERIAL_CLOCK
+#define CONFIG_BAUDRATE		115200
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for setup	*/
+#define SPD_EEPROM_ADDRESS {0x51, 0x52}	/* SPD i2c spd addresses	*/
+#define IIC0_DIMM0_ADDR		0x51
+#define IIC0_DIMM1_ADDR		0x52
+#undef  CONFIG_STRESS
+#undef  ENABLE_ECC
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		100000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CFG_SPD_BUS_NUM		0	/* The I2C bus for SPD		*/
+
+#define IIC0_BOOTPROM_ADDR	0x50
+#define IIC0_ALT_BOOTPROM_ADDR	0x54
+
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR	(0x50)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/* I2C RTC */
+#define CONFIG_RTC_M41T11	1
+#define CFG_RTC_BUS_NUM		1	/* The I2C bus for RTC		*/
+#define CFG_I2C_RTC_ADDR	0x68
+#define CFG_M41T11_BASE_YEAR	1900	/* play along with linux	*/
+
+/* I2C DTT */
+#define CONFIG_DTT_ADM1021	1	/* ADM1021 temp sensor support	*/
+#define CFG_DTT_BUS_NUM		1	/* The I2C bus for DTT		*/
+/*
+ * standard dtt sensor configuration - bottom bit will determine local or
+ * remote sensor of the ADM1021, the rest determines index into
+ * CFG_DTT_ADM1021 array below.
+ */
+#define CONFIG_DTT_SENSORS	{ 0, 1 }
+
+/*
+ * ADM1021 temp sensor configuration (see dtt/adm1021.c for details).
+ * there will be one entry in this array for each two (dummy) sensors in
+ * CONFIG_DTT_SENSORS.
+ *
+ * For Katmai board:
+ * - only one ADM1021
+ * - i2c addr 0x18
+ * - conversion rate 0x02 = 0.25 conversions/second
+ * - ALERT ouput disabled
+ * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
+ * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
+ */
+#define CFG_DTT_ADM1021		{ { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} }
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#define	CFG_ENV_IS_IN_FLASH	1	/* Environment uses flash	*/
+
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"hostname=katmai\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
+		"bootm\0"						\
+	"rootpath=/opt/eldk/ppc_4xx\0"				\
+	"bootfile=katmai/uImage\0"					\
+	"kernel_addr=fff10000\0"					\
+	"ramdisk_addr=fff20000\0"					\
+	"initrd_high=30000000\0"					\
+	"load=tftp 200000 katmai/u-boot.bin\0"				\
+	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
+		"cp.b ${fileaddr} fffc0000 ${filesize};"		\
+		"setenv filesize;saveenv\0"				\
+	"upd=run load;run update\0"					\
+	"kozio=bootm ffc60000\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
+				CFG_CMD_ASKENV	| \
+				CFG_CMD_EEPROM	| \
+				CFG_CMD_DATE	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_DIAG	| \
+				CFG_CMD_DTT	| \
+				CFG_CMD_ELF	| \
+				CFG_CMD_EXT2	| \
+				CFG_CMD_FAT	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_IRQ	| \
+				CFG_CMD_MII	| \
+				CFG_CMD_NET	| \
+				CFG_CMD_NFS	| \
+				CFG_CMD_PCI	| \
+				CFG_CMD_PING	| \
+				CFG_CMD_REGINFO	| \
+				CFG_CMD_SDRAM)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define	CONFIG_IBM_EMAC4_V4	1	/* 440SPe has this EMAC version	*/
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
+#define CONFIG_HAS_ETH0
+#define CONFIG_PHY_RESET        1	/* reset phy upon startup	*/
+#define CONFIG_PHY_RESET_DELAY	1000
+#define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
+#define CONFIG_NET_MULTI		/* needed for NetConsole	*/
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP				/* undef to save memory		*/
+#define CFG_PROMPT		"=> "		/* Monitor Command Prompt	*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS		16		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on		*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM		*/
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address		*/
+#define CFG_EXTBDINFO		1		/* To use extended board_into (bd_t) */
+
+#define CFG_HZ			1000		/* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+#define CFG_4xx_RESET_TYPE	0x2	/* use chip reset on this board	*/
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
+
+#define CFG_FLASH_BANKS_LIST    {CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS     1		    /* number of banks	    */
+#define CFG_MAX_FLASH_SECT	1024		    /* sectors per device   */
+
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_ENV_SECT_SIZE	0x20000 /* size of one complete sector	*/
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+/* General PCI */
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_PNP		1	/* do pci plug-and-play		*/
+#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
+#undef CONFIG_PCI_CONFIG_HOST_BRIDGE
+
+/* Board-specific PCI */
+#define CFG_PCI_PRE_INIT	1	/* enable board pci_pre_init()	*/
+#define CFG_PCI_TARGET_INIT		/* let board init pci target    */
+#undef	CFG_PCI_MASTER_INIT
+
+#define CFG_PCI_SUBSYS_VENDORID 0x1014	/* IBM				*/
+#define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever			*/
+/* #define CFG_PCI_SUBSYS_ID	CFG_PCI_SUBSYS_DEVICEID */
+
+/*
+ *  NETWORK Support (PCI):
+ */
+/* Support for Intel 82557/82559/82559ER chips. */
+#define CONFIG_EEPRO100
+
+/*-----------------------------------------------------------------------
+ * Xilinx System ACE support
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYSTEMACE	1	/* Enable SystemACE support	*/
+#define CFG_SYSTEMACE_WIDTH	16	/* Data bus width is 16		*/
+#define CFG_SYSTEMACE_BASE	CFG_ACE_BASE
+#define CONFIG_DOS_PARTITION	1
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+
+/* Memory Bank 0 (Flash) initialization					*/
+#define CFG_EBC_PB0AP		(EBC_BXAP_BME_DISABLED      |		\
+				 EBC_BXAP_TWT_ENCODE(7)     |		\
+				 EBC_BXAP_BCE_DISABLE       |		\
+				 EBC_BXAP_BCT_2TRANS        |		\
+				 EBC_BXAP_CSN_ENCODE(0)     |		\
+				 EBC_BXAP_OEN_ENCODE(0)     |		\
+				 EBC_BXAP_WBN_ENCODE(0)     |		\
+				 EBC_BXAP_WBF_ENCODE(0)     |		\
+				 EBC_BXAP_TH_ENCODE(0)      |		\
+				 EBC_BXAP_RE_DISABLED       |		\
+				 EBC_BXAP_SOR_DELAYED       |		\
+				 EBC_BXAP_BEM_WRITEONLY     |		\
+				 EBC_BXAP_PEN_DISABLED)
+#define CFG_EBC_PB0CR		(EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) |	\
+				 EBC_BXCR_BS_16MB                    |	\
+				 EBC_BXCR_BU_RW                      |	\
+				 EBC_BXCR_BW_16BIT)
+
+/* Memory Bank 1 (Xilinx System ACE controller) initialization		*/
+#define CFG_EBC_PB1AP		0x7F8FFE80
+#define CFG_EBC_PB1CR		(EBC_BXCR_BAS_ENCODE(CFG_ACE_BASE)  |	\
+				 EBC_BXCR_BS_1MB                    |	\
+				 EBC_BXCR_BU_RW                     |	\
+				 EBC_BXCR_BW_16BIT)
+
+/*-------------------------------------------------------------------------
+ * Initialize EBC CONFIG -
+ * Keep the Default value, but the bit PDT which has to be set to 1 ?TBC
+ * default value : 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
+ *-------------------------------------------------------------------------*/
+#define CFG_EBC_CFG		(EBC_CFG_LE_UNLOCK    |	\
+				 EBC_CFG_PTD_ENABLE   |	\
+				 EBC_CFG_RTC_16PERCLK | \
+				 EBC_CFG_ATC_PREVIOUS | \
+				 EBC_CFG_DTC_PREVIOUS | \
+				 EBC_CFG_CTC_PREVIOUS | \
+				 EBC_CFG_OEO_PREVIOUS | \
+				 EBC_CFG_EMC_DEFAULT  |	\
+				 EBC_CFG_PME_DISABLE  |	\
+				 EBC_CFG_PR_16)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/*Initial Memory map for Linux*/
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs		*/
+#define CFG_CACHELINE_SIZE	32	/* ...				*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+#endif	/* __CONFIG_H */
diff --git a/include/ppc405.h b/include/ppc405.h
index e475fa5..a49912c 100644
--- a/include/ppc405.h
+++ b/include/ppc405.h
@@ -240,6 +240,7 @@
   #define pbesr0      0x21    /* periph bus error status reg 0       */
   #define pbesr1      0x22    /* periph bus error status reg 1       */
   #define epcr        0x23    /* external periph control reg         */
+#define EBC0_CFG	0x23	/* external bus configuration reg	*/
 
 #ifdef CONFIG_405EP
 /******************************************************************************
diff --git a/include/ppc440.h b/include/ppc440.h
index 91cff41..c24f5b7 100644
--- a/include/ppc440.h
+++ b/include/ppc440.h
@@ -533,9 +533,12 @@
 #define SDRAM_MCSTAT_MIC_MASK		0x80000000	/* Memory init status mask	*/
 #define SDRAM_MCSTAT_MIC_NOTCOMP	0x00000000	/* Mem init not complete	*/
 #define SDRAM_MCSTAT_MIC_COMP		0x80000000	/* Mem init complete		*/
-#define SDRAM_MCSTAT_SRMS_MASK		0x80000000	/* Mem self refresh stat mask	*/
+#define SDRAM_MCSTAT_SRMS_MASK		0x40000000	/* Mem self refresh stat mask	*/
 #define SDRAM_MCSTAT_SRMS_NOT_SF	0x00000000	/* Mem not in self refresh	*/
-#define SDRAM_MCSTAT_SRMS_SF		0x80000000	/* Mem in self refresh		*/
+#define SDRAM_MCSTAT_SRMS_SF		0x40000000	/* Mem in self refresh		*/
+#define SDRAM_MCSTAT_IDLE_MASK		0x20000000	/* Mem self refresh stat mask	*/
+#define SDRAM_MCSTAT_IDLE_NOT		0x00000000	/* Mem contr not idle		*/
+#define SDRAM_MCSTAT_IDLE		0x20000000	/* Mem contr idle		*/
 
 /*-----------------------------------------------------------------------------+
 |  Memory Controller Options 1
@@ -730,6 +733,7 @@
 #define SDRAM_WRDTR_LLWP_1_CYC		0x00000000
 #define SDRAM_WRDTR_WTR_MASK		0x0E000000
 #define SDRAM_WRDTR_WTR_0_DEG		0x06000000
+#define SDRAM_WRDTR_WTR_90_DEG_ADV	0x04000000
 #define SDRAM_WRDTR_WTR_180_DEG_ADV	0x02000000
 #define SDRAM_WRDTR_WTR_270_DEG_ADV	0x00000000
 
@@ -847,6 +851,7 @@
 #define pbear		0x20	/* periph bus error addr reg		*/
 #define pbesr		0x21	/* periph bus error status reg		*/
 #define xbcfg		0x23	/* external bus configuration reg	*/
+#define EBC0_CFG	0x23	/* external bus configuration reg	*/
 #define xbcid		0x24	/* external bus core id reg		*/
 
 #if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \