Merge branch 'master' of git://git.denx.de/u-boot-spi

7 files changed, 333 insertions, 14 deletions

diff --git a/doc/SPI/README.sh_qspi_test b/doc/SPI/README.sh_qspi_test
new file mode 100644
index 0000000..8a33fec
--- /dev/null
+++ b/doc/SPI/README.sh_qspi_test
@@ -0,0 +1,38 @@
+-------------------------------------------------
+   Simple steps used to test the SH-QSPI at U-Boot
+-------------------------------------------------
+
+#0, Currently, SH-QSPI is used by lager board (Renesas ARM SoC R8A7790)
+    and koelsch board (Renesas ARM SoC R8A7791). These boot from SPI ROM
+    basically. Thus, U-Boot start, SH-QSPI will is operating normally.
+
+#1, build U-Boot and load u-boot.bin
+
+  => tftpboot 40000000 u-boot.bin
+  sh_eth Waiting for PHY auto negotiation to complete.. done
+  sh_eth: 100Base/Half
+  Using sh_eth device
+  TFTP from server 192.168.169.1; our IP address is 192.168.169.79
+  Filename 'u-boot.bin'.
+  Load address: 0x40000000
+  Loading: ############
+    2.5 MiB/s
+  done
+  Bytes transferred = 175364 (2ad04 hex)
+
+#2, Commands to erase/write u-boot to flash device
+
+  Note: This method is description of the lager board. If you want to use the
+  other boards, please change the value according to each environment.
+
+  =>  sf probe 0
+  SF: Detected S25FL512S_256K with page size 512 Bytes, erase size 64 KiB, total 64 MiB
+  => sf erase 80000 40000
+  SF: 262144 bytes @ 0x80000 Erased: OK
+  => sf write 40000000 80000 175364
+  SF: 1528676 bytes @ 0x80000 Written: OK
+  =>
+
+#3, Push reset button.
+
+  If you're written correctly and driver works properly, U-Boot starts.
diff --git a/drivers/mtd/spi/sf_ops.c b/drivers/mtd/spi/sf_ops.c
index 108665f..e316a69 100644
--- a/drivers/mtd/spi/sf_ops.c
+++ b/drivers/mtd/spi/sf_ops.c
@@ -273,9 +273,15 @@ int spi_flash_cmd_read_ops(struct spi_flash *flash, u32 offset,
 
 	/* Handle memory-mapped SPI */
 	if (flash->memory_map) {
+		ret = spi_claim_bus(flash->spi);
+		if (ret) {
+			debug("SF: unable to claim SPI bus\n");
+			return ret;
+		}
 		spi_xfer(flash->spi, 0, NULL, NULL, SPI_XFER_MMAP);
 		memcpy(data, flash->memory_map + offset, len);
 		spi_xfer(flash->spi, 0, NULL, NULL, SPI_XFER_MMAP_END);
+		spi_release_bus(flash->spi);
 		return 0;
 	}
 
diff --git a/drivers/mtd/spi/sf_probe.c b/drivers/mtd/spi/sf_probe.c
index c1eb754..b863a98 100644
--- a/drivers/mtd/spi/sf_probe.c
+++ b/drivers/mtd/spi/sf_probe.c
@@ -60,6 +60,7 @@ static const struct spi_flash_params spi_flash_params_table[] = {
 	{"GD25LQ32",	   0xc86016, 0x0,	64 * 1024,    64,	       SECT_4K},
 #endif
 #ifdef CONFIG_SPI_FLASH_MACRONIX	/* MACRONIX */
+	{"MX25L2006E",	   0xc22012, 0x0,	64 * 1024,     4,	             0},
 	{"MX25L4005",	   0xc22013, 0x0,	64 * 1024,     8,	             0},
 	{"MX25L8005",	   0xc22014, 0x0,	64 * 1024,    16,	             0},
 	{"MX25L1605D",	   0xc22015, 0x0,	64 * 1024,    32,	             0},
@@ -67,7 +68,7 @@ static const struct spi_flash_params spi_flash_params_table[] = {
 	{"MX25L6405D",	   0xc22017, 0x0,	64 * 1024,   128,	             0},
 	{"MX25L12805",	   0xc22018, 0x0,	64 * 1024,   256,	             0},
 	{"MX25L25635F",	   0xc22019, 0x0,	64 * 1024,   512,	             0},
-	{"MX25L51235F",	   0xc2201A, 0x0,	64 * 1024,  1024,	             0},
+	{"MX25L51235F",	   0xc2201a, 0x0,	64 * 1024,  1024,	             0},
 	{"MX25L12855E",	   0xc22618, 0x0,	64 * 1024,   256,	             0},
 #endif
 #ifdef CONFIG_SPI_FLASH_SPANSION	/* SPANSION */
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index ed4ecd7..d5a7143 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -30,6 +30,7 @@ obj-$(CONFIG_OMAP3_SPI) += omap3_spi.o
 obj-$(CONFIG_SANDBOX_SPI) += sandbox_spi.o
 obj-$(CONFIG_SOFT_SPI) += soft_spi.o
 obj-$(CONFIG_SH_SPI) += sh_spi.o
+obj-$(CONFIG_SH_QSPI) += sh_qspi.o
 obj-$(CONFIG_FSL_ESPI) += fsl_espi.o
 obj-$(CONFIG_FDT_SPI) += fdt_spi.o
 obj-$(CONFIG_TEGRA20_SFLASH) += tegra20_sflash.o
diff --git a/drivers/spi/sh_qspi.c b/drivers/spi/sh_qspi.c
new file mode 100644
index 0000000..edeb42d
--- /dev/null
+++ b/drivers/spi/sh_qspi.c
@@ -0,0 +1,277 @@
+/*
+ * SH QSPI (Quad SPI) driver
+ *
+ * Copyright (C) 2013 Renesas Electronics Corporation
+ * Copyright (C) 2013 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <spi.h>
+#include <asm/io.h>
+
+/* SH QSPI register bit masks <REG>_<BIT> */
+#define SPCR_MSTR	0x08
+#define SPCR_SPE	0x40
+#define SPSR_SPRFF	0x80
+#define SPSR_SPTEF	0x20
+#define SPPCR_IO3FV	0x04
+#define SPPCR_IO2FV	0x02
+#define SPPCR_IO1FV	0x01
+#define SPBDCR_RXBC0	(1 << 0)
+#define SPCMD_SCKDEN	(1 << 15)
+#define SPCMD_SLNDEN	(1 << 14)
+#define SPCMD_SPNDEN	(1 << 13)
+#define SPCMD_SSLKP	(1 << 7)
+#define SPCMD_BRDV0	(1 << 2)
+#define SPCMD_INIT1	SPCMD_SCKDEN | SPCMD_SLNDEN | \
+			SPCMD_SPNDEN | SPCMD_SSLKP | \
+			SPCMD_BRDV0
+#define SPCMD_INIT2	SPCMD_SPNDEN | SPCMD_SSLKP | \
+			SPCMD_BRDV0
+#define SPBFCR_TXRST	(1 << 7)
+#define SPBFCR_RXRST	(1 << 6)
+
+/* SH QSPI register set */
+struct sh_qspi_regs {
+	unsigned char spcr;
+	unsigned char sslp;
+	unsigned char sppcr;
+	unsigned char spsr;
+	unsigned long spdr;
+	unsigned char spscr;
+	unsigned char spssr;
+	unsigned char spbr;
+	unsigned char spdcr;
+	unsigned char spckd;
+	unsigned char sslnd;
+	unsigned char spnd;
+	unsigned char dummy0;
+	unsigned short spcmd0;
+	unsigned short spcmd1;
+	unsigned short spcmd2;
+	unsigned short spcmd3;
+	unsigned char spbfcr;
+	unsigned char dummy1;
+	unsigned short spbdcr;
+	unsigned long spbmul0;
+	unsigned long spbmul1;
+	unsigned long spbmul2;
+	unsigned long spbmul3;
+};
+
+struct sh_qspi_slave {
+	struct spi_slave	slave;
+	struct sh_qspi_regs	*regs;
+};
+
+static inline struct sh_qspi_slave *to_sh_qspi(struct spi_slave *slave)
+{
+	return container_of(slave, struct sh_qspi_slave, slave);
+}
+
+static void sh_qspi_init(struct sh_qspi_slave *ss)
+{
+	/* QSPI initialize */
+	/* Set master mode only */
+	writeb(SPCR_MSTR, &ss->regs->spcr);
+
+	/* Set SSL signal level */
+	writeb(0x00, &ss->regs->sslp);
+
+	/* Set MOSI signal value when transfer is in idle state */
+	writeb(SPPCR_IO3FV|SPPCR_IO2FV, &ss->regs->sppcr);
+
+	/* Set bit rate. See 58.3.8 Quad Serial Peripheral Interface */
+	writeb(0x01, &ss->regs->spbr);
+
+	/* Disable Dummy Data Transmission */
+	writeb(0x00, &ss->regs->spdcr);
+
+	/* Set clock delay value */
+	writeb(0x00, &ss->regs->spckd);
+
+	/* Set SSL negation delay value */
+	writeb(0x00, &ss->regs->sslnd);
+
+	/* Set next-access delay value */
+	writeb(0x00, &ss->regs->spnd);
+
+	/* Set equence command */
+	writew(SPCMD_INIT2, &ss->regs->spcmd0);
+
+	/* Reset transfer and receive Buffer */
+	setbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
+
+	/* Clear transfer and receive Buffer control bit */
+	clrbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
+
+	/* Set equence control method. Use equence0 only */
+	writeb(0x00, &ss->regs->spscr);
+
+	/* Enable SPI function */
+	setbits_8(&ss->regs->spcr, SPCR_SPE);
+}
+
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+	return 1;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+	struct sh_qspi_slave *ss = to_sh_qspi(slave);
+
+	/* Set master mode only */
+	writeb(SPCR_MSTR, &ss->regs->spcr);
+
+	/* Set command */
+	writew(SPCMD_INIT1, &ss->regs->spcmd0);
+
+	/* Reset transfer and receive Buffer */
+	setbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
+
+	/* Clear transfer and receive Buffer control bit */
+	clrbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
+
+	/* Set equence control method. Use equence0 only */
+	writeb(0x00, &ss->regs->spscr);
+
+	/* Enable SPI function */
+	setbits_8(&ss->regs->spcr, SPCR_SPE);
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+	struct sh_qspi_slave *ss = to_sh_qspi(slave);
+
+	/* Disable SPI Function */
+	clrbits_8(&ss->regs->spcr, SPCR_SPE);
+}
+
+void spi_init(void)
+{
+	/* nothing to do */
+}
+
+struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
+		unsigned int max_hz, unsigned int mode)
+{
+	struct sh_qspi_slave *ss;
+
+	if (!spi_cs_is_valid(bus, cs))
+		return NULL;
+
+	ss = spi_alloc_slave(struct sh_qspi_slave, bus, cs);
+	if (!ss) {
+		printf("SPI_error: Fail to allocate sh_qspi_slave\n");
+		return NULL;
+	}
+
+	ss->regs = (struct sh_qspi_regs *)CONFIG_SH_QSPI_BASE;
+
+	/* Init SH QSPI */
+	sh_qspi_init(ss);
+
+	return &ss->slave;
+}
+
+void spi_free_slave(struct spi_slave *slave)
+{
+	struct sh_qspi_slave *spi = to_sh_qspi(slave);
+
+	free(spi);
+}
+
+int spi_claim_bus(struct spi_slave *slave)
+{
+	return 0;
+}
+
+void spi_release_bus(struct spi_slave *slave)
+{
+}
+
+int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
+	     void *din, unsigned long flags)
+{
+	struct sh_qspi_slave *ss = to_sh_qspi(slave);
+	unsigned long nbyte;
+	int ret = 0;
+	unsigned char dtdata = 0, drdata;
+	unsigned char *tdata = &dtdata, *rdata = &drdata;
+	unsigned long *spbmul0 = &ss->regs->spbmul0;
+
+	if (dout == NULL && din == NULL) {
+		if (flags & SPI_XFER_END)
+			spi_cs_deactivate(slave);
+		return 0;
+	}
+
+	if (bitlen % 8) {
+		printf("%s: bitlen is not 8bit alined %d", __func__, bitlen);
+		return 1;
+	}
+
+	nbyte = bitlen / 8;
+
+	if (flags & SPI_XFER_BEGIN) {
+		spi_cs_activate(slave);
+
+		/* Set 1048576 byte */
+		writel(0x100000, spbmul0);
+	}
+
+	if (flags & SPI_XFER_END)
+		writel(nbyte, spbmul0);
+
+	if (dout != NULL)
+		tdata = (unsigned char *)dout;
+
+	if (din != NULL)
+		rdata = din;
+
+	while (nbyte > 0) {
+		while (!(readb(&ss->regs->spsr) & SPSR_SPTEF)) {
+			if (ctrlc()) {
+				puts("abort\n");
+				return 1;
+			}
+			udelay(10);
+		}
+
+		writeb(*tdata, (unsigned char *)(&ss->regs->spdr));
+
+		while ((readw(&ss->regs->spbdcr) != SPBDCR_RXBC0)) {
+			if (ctrlc()) {
+				puts("abort\n");
+				return 1;
+			}
+			udelay(1);
+		}
+
+		while (!(readb(&ss->regs->spsr) & SPSR_SPRFF)) {
+			if (ctrlc()) {
+				puts("abort\n");
+				return 1;
+			}
+			udelay(10);
+		}
+
+		*rdata = readb((unsigned char *)(&ss->regs->spdr));
+
+		if (dout != NULL)
+			tdata++;
+		if (din != NULL)
+			rdata++;
+
+		nbyte--;
+	}
+
+	if (flags & SPI_XFER_END)
+		spi_cs_deactivate(slave);
+
+	return ret;
+}
diff --git a/drivers/spi/tegra114_spi.c b/drivers/spi/tegra114_spi.c
index 4d2af48..810fa47 100644
--- a/drivers/spi/tegra114_spi.c
+++ b/drivers/spi/tegra114_spi.c
@@ -289,9 +289,6 @@ int tegra114_spi_xfer(struct spi_slave *slave, unsigned int bitlen,
 	reg = readl(&regs->fifo_status);
 	writel(reg, &regs->fifo_status);
 
-	/* clear ready bit */
-	setbits_le32(&regs->xfer_status, SPI_XFER_STS_RDY);
-
 	clrsetbits_le32(&regs->command1, SPI_CMD1_CS_SW_VAL,
 			SPI_CMD1_RX_EN | SPI_CMD1_TX_EN | SPI_CMD1_LSBY_FE |
 			(slave->cs << SPI_CMD1_CS_SEL_SHIFT));
@@ -305,7 +302,6 @@ int tegra114_spi_xfer(struct spi_slave *slave, unsigned int bitlen,
 	/* handle data in 32-bit chunks */
 	while (num_bytes > 0) {
 		int bytes;
-		int is_read = 0;
 		int tm, i;
 
 		tmpdout = 0;
@@ -319,6 +315,9 @@ int tegra114_spi_xfer(struct spi_slave *slave, unsigned int bitlen,
 
 		num_bytes -= bytes;
 
+		/* clear ready bit */
+		setbits_le32(&regs->xfer_status, SPI_XFER_STS_RDY);
+
 		clrsetbits_le32(&regs->command1,
 				SPI_CMD1_BIT_LEN_MASK << SPI_CMD1_BIT_LEN_SHIFT,
 				(bytes * 8 - 1) << SPI_CMD1_BIT_LEN_SHIFT);
@@ -329,20 +328,14 @@ int tegra114_spi_xfer(struct spi_slave *slave, unsigned int bitlen,
 		 * Wait for SPI transmit FIFO to empty, or to time out.
 		 * The RX FIFO status will be read and cleared last
 		 */
-		for (tm = 0, is_read = 0; tm < SPI_TIMEOUT; ++tm) {
+		for (tm = 0; tm < SPI_TIMEOUT; ++tm) {
 			u32 fifo_status, xfer_status;
 
-			fifo_status = readl(&regs->fifo_status);
-
-			/* We can exit when we've had both RX and TX activity */
-			if (is_read &&
-			    (fifo_status & SPI_FIFO_STS_TX_FIFO_EMPTY))
-				break;
-
 			xfer_status = readl(&regs->xfer_status);
 			if (!(xfer_status & SPI_XFER_STS_RDY))
 				continue;
 
+			fifo_status = readl(&regs->fifo_status);
 			if (fifo_status & SPI_FIFO_STS_ERR) {
 				debug("%s: got a fifo error: ", __func__);
 				if (fifo_status & SPI_FIFO_STS_TX_FIFO_OVF)
@@ -367,7 +360,6 @@ int tegra114_spi_xfer(struct spi_slave *slave, unsigned int bitlen,
 
 			if (!(fifo_status & SPI_FIFO_STS_RX_FIFO_EMPTY)) {
 				tmpdin = readl(&regs->rx_fifo);
-				is_read = 1;
 
 				/* swap bytes read in */
 				if (din != NULL) {
@@ -377,6 +369,9 @@ int tegra114_spi_xfer(struct spi_slave *slave, unsigned int bitlen,
 					}
 					din += bytes;
 				}
+
+				/* We can exit when we've had both RX and TX */
+				break;
 			}
 		}
 
diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h
index 48b47cb..f210ed8 100644
--- a/include/configs/dra7xx_evm.h
+++ b/include/configs/dra7xx_evm.h
@@ -60,6 +60,7 @@
 #define CONFIG_SPI_FLASH_SPANSION
 #define CONFIG_CMD_SF
 #define CONFIG_CMD_SPI
+#define CONFIG_SPI_FLASH_BAR
 #define CONFIG_TI_SPI_MMAP
 #define CONFIG_SF_DEFAULT_SPEED                48000000
 #define CONFIG_DEFAULT_SPI_MODE                SPI_MODE_3